• 제목/요약/키워드: Air Nozzle Diameter

검색결과 190건 처리시간 0.021초

INFLUENCE OF ALR ON DISINTEGRATION CHARACTERISTICS IN PNEUMATIC SPRAY

  • Lee, S.G.;Joo, B.C.;Kim, K.C.;Rho, B.J.
    • International Journal of Automotive Technology
    • /
    • 제1권2호
    • /
    • pp.95-100
    • /
    • 2000
  • The droplet and the turbulent characteristics of a counterflowing internal mixing pneumatic nozzle mainly focused. The measurements were made using a Phase Doppler Particle Analyzer under the different air pressures. The nozzle with tangential-drilled holes at an angle of 30 to the central axis has been designed. The spatial distributions of velocities, fluctuating velocities, droplet diameters and SMD were quantitatively and qualitatively fluctuating velocities were substantially higher than the radial and the tangential ones. This implies that the disintegration process is enhanced with the higher air pressure. The larger droplets were detected near the spray centerline at the upstream while the smaller ones were generated at the downstream. This was attributed to the lower rates of spherical particles which were not subject to instantaneous breakup. However, substantial increases in SMD from the central part tower spray periphery were predictable in downstream regions.

  • PDF

Atomization Improvement of a Liquid Jet with Wall Impingement and its Application to a Jet Engine Atomizer

  • Shiga, Seiichi
    • 한국분무공학회지
    • /
    • 제11권3호
    • /
    • pp.176-189
    • /
    • 2006
  • In the present study, capability of improving the liquid atomization of a high-speed liquid jet by using wall impingement is explored, and its application to a jet engine atomize. is demonstrated. Water is injected from a thin nozzle. The liquid jet impinges on a wall positioned close to the nozzle exit, forming a liquid film. The liquid film velocity and the SMD were measured with PDA and LDSA, respectively. It was shown that the SMD of the droplets was determined by the liquid film velocity and impingement angle, regardless of the injection pressure or impingement wall diameter. When the liquid film velocity was smaller than 300m/s, a smaller SMD was obtained, compared with a simple free jet. This wall impingement technique was applied to a conventional air-blasting nozzle for jet engines. A real-size air-blasting burner was installed in a test rig in which three thin holes were made to accommodate liquid injection toward the intermediate ring, as an impingement wall. The air velocity was varied from 41 to 92m/s, and the liquid injection pressure was varied from 0.5 to 7.5 MPa. Combining wall impinging pressure atomization with gas-blasting produces remarkable improvement in atomization, which is contributed by the droplets produced in the pressure atomization mode. Comparison with the previous formulation for conventional gas-blasting atomization is also made, and the effectiveness of utilizing pressure atomization with wall impingement is shown.

  • PDF

관내 분무액적의 유동특성에 관한 실험적 연구 (An Experimental Study on the Dynamic Behavior of Spray Droplets in the Wind Tunnel)

  • 박대식;최혁준;박상균;김명환;오철;윤석훈
    • 한국마린엔지니어링학회:학술대회논문집
    • /
    • 한국마린엔지니어링학회 2002년도 춘계학술대회논문집
    • /
    • pp.95-100
    • /
    • 2002
  • This study was experimentally performed to investigate flow characteristics of spray droplets in the wind tunnel. Behavior of the spray droplets in the pipe was observed and the deposition rate of droplets on the surface of pipe as liquid film was measured. The experiments were carried out for a variety of parameter, such as velocity of feed air, spray angle of nozzle, and diameter of droplet. From the visual observation of the spray droplets in the pipe and the measurement of deposition rate on the pipe, the general understanding of droplets behavior for desuperheater was provided.

  • PDF

An Experimental Study of the Performance Characteristics with Four Different Rotor Blade Shapes on a Small Mixed-Type Turbine

  • Cho Soo-Yong;Cho Tae-Hwan;Choi Sang-Kyu
    • Journal of Mechanical Science and Technology
    • /
    • 제19권7호
    • /
    • pp.1478-1487
    • /
    • 2005
  • A small mixed-type turbine with a diameter of 19.9 mm has been substituted for a rotational part of pencil-type air tool. Usually, a vane-type rotor is applied to the rotational part of the air tool. However, the vane-type rotor has some problems, such as friction, abrasion, and necessity of accurate assembly etc.,. These problems make the life time of the vane-type air tool short, but air tools operated by mixed-type turbines are free of friction and abrasion because the turbine rotor dose not contact with the casing. Moreover, it is assembled easily because of no axis offset. These characteristics are merits for using air tools, but loss of power is inevitable on a non-contacting type rotor due to flow loss, tip clearance loss, and profile loss etc.,. In this study, four different rotors are tested, and their characteristics are investigated by measuring the specific output power. Additionally, optimum nozzle location against the rotor is studied. Output powers are obtained through measured pressure, temperature, torque, rotational speed, and flow rate. The experimental results obtained with four different rotors show that the rotor blade shape greatly influences to the performance, and the optimum nozzle location exists near the mid span of the rotor.

감압용 배수탱크내의 분기형 증기분사기의 유동특성에 관한 연구 (A Study on Flow Characteristics of Branch Type Sparger in Drain Tank for Depressurization)

  • 김광추;박만흥;박경석
    • 설비공학논문집
    • /
    • 제13권5호
    • /
    • pp.356-367
    • /
    • 2001
  • A numerical analysis on branch type sparger in drain tank for depressurization is performed to investigate the flow characteristics due to the change of design factor. As the result of this study, sparger\\`s flow resistance coefficient(K) is 3.53 at the present design condition when engineering margin for surface roughness is considered as 20%, and flow ratio into branch pipe ($Q_s/Q_i$) is 0.41. The correlation for calculating flow resistance coefficients as design factor is presented. Flow resistance coefficient is increased as section area ratio of branch pipe for main pipe and outlet nozzle diameter of main pipe decreasing, but the effects of branch angle and inlet flow rate of main pipe are small. As the change rate of ($Q_s/Q_i$)becomes larger, the change rate of flow resistance coefficient increases. The rate of pressure loss has the largest change as section area ratio changing. The condition of maximum flow resistance in sparger is when the outlet nozzle diameter ratio of main pipe ($D_e/D_i$) is 0.167, the section area ratio ($A_s/A_i$) is 0.1 and the branch angle ($\alpha$) is 55^{\circ}$.

  • PDF

다수 부분 예혼합 화염의 화염날림 유속 확대 (Nozzle configurations for partially premixed interacting jet flame to enhance blowout limits)

  • 이병준;김진현
    • 한국연소학회:학술대회논문집
    • /
    • 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
    • /
    • pp.79-84
    • /
    • 2004
  • For the non-premixed interacting jet flames, it has been reported that if eight small nozzles are arranged along the circle of 40 $^{\sim}$ 72 times the diameter of single jet, the flames are not extinguished over 2oom/s. In this research, experiments were extended to the partially premixed cases to reduce both flame temperature and NOx emission. Nine nozzles were used- eight was evenly located along the perimeter of the imaginary circle and one at the geometric centre. The space between nozzles, S, the equivalence ratio, ${\Phi}$, the exit velocity and the role of the jet from the centre nozzle were considered. Normally, flame was lifted and flame base was located inside the imaginary circle made by the nozzle. As nozzles went away from each other, blowout velocity increased and then decreased. The maximum blowout velocity diminished with the addition of air to the fuel stream. When the fuel and/or oxidizer were not fed through the centre nozzle, the maximum blowout velocity obtained by varying Sand ${\Phi}$ was around 160m/s. Optimum nozzle separation distance at which peak blowout velocity obtained also decreased with ${\Phi}$ decrease. Flame base became leaner as approaching to the blowout. It seemed that lots of air was supplied to the flame stabilizing region by the entrainment and partially premixing. To approve this idea and to enhance the blowout velocity, fuel was supplied to the centre region. With the small amount of fuel through the centre nozzle, partially premixed flame could be sustained till sonic velocities. It seemed that the stabilizing mechanism in partially premixed interacting flame was different from that of non-premixed case because one was stabilized by the fuel supply through the centre nozzle but the other destabilized.

  • PDF

화염의 상호작용에 의한 부분 예혼합화염의 화염날림 유속 확대 (Nozzle Configurations for Partially Premixed Interacting Jet Flame to Enhance Blowout Limits)

  • 김진현;이병준
    • 대한기계학회논문집B
    • /
    • 제29권1호
    • /
    • pp.71-79
    • /
    • 2005
  • For the non-premixed interacting jet flames, it has been reported that if eight small nozzles are arranged along the circle of $40{\sim}72$ times the diameter of single jet, the flames are not extinguished even in 200m/s. In this research, experiments were extended to the partially premixed cases to reduce both flame temperature and NOx emission. Nine nozzles were used- eight was evenly located along the perimeter of the imaginary circle and one at the geometric centre. The space between nozzles, S, the equivalence ratio, ${\phi}$, the exit velocity and the role of the jet from the centre nozzle were considered. Normally, flame was lifted and flame base was located inside the imaginary circle made by the nozzle. As nozzles went away from each other, blowout velocity increased and then decreased. The maximum blowout velocity diminished with the addition of air to the fuel stream. When the fuel and/or oxidizer were not fed through the centre nozzle, the maximum blowout velocity obtained by varying S and ${\phi}$ was around 160m/s. Optimum nozzle separation distance at which peak blowout velocity obtained also decreased with ${\phi}$ decrease. Flame base became leaner as approaching to the blowout. It seemed that lots of air was supplied to the flame stabilizing region by the entrainment and partially premixing. To approve this idea and to enhance the blowout velocity, fuel was supplied to the centre region. With the small amount of fuel through the centre nozzle, partially premixed flame could be sustained till sonic velocities. It seemed that the stabilizing mechanism in partially premixed interacting flame was different from that of non-premixed case because one was stabilized by the fuel supply through the centre nozzle but the other destabilized.

2유체노즐의 액체풀 화재 소화 성능에 대한 검토 (Examination on Liquid Pool Fire Extinguishment Performance of Twin-fluid Nozzle)

  • 정찬석;이치영
    • 한국화재소방학회논문지
    • /
    • 제31권4호
    • /
    • pp.59-64
    • /
    • 2017
  • 본 연구에서는 2유체노즐의 액체풀 (Liquid pool) 화재 소화 성능에 대하여 선행적인 검토를 수행하였다. 액체풀 화재의 경우, 에탄올 (Ethanol) 1200 ml를 이용하였으며, 물 공급 유량은 632 ml/min, 공기의 공급 유량은 40 l/min과 70 l/min으로 설정하였다. 본 실험조건에서 2유체노즐을 이용하여 화재 소화 실험을 수행하였고, 2유체노즐의 분사 특성 (액적 크기 및 유량 분포)을 측정하였다. 실험 결과, 공기의 유량이 많은 조건에서 빠른 시간 안에 성공적으로 화재를 소화할 수 있었고, 이러한 결과에 대하여 가시화 및 2유체노즐 분사 특성 데이터를 토대로 분석하였다. 또한, 기존 연구의 일부 결과와 비교를 통하여, 2유체노즐이 단일유체노즐에 비해 더욱 작은 물의 유량 조건에서도 화재 소화를 할 수 있을 가능성이 있음을 확인하였다.

압력식 노즐에서 송풍공기가 미립화에 미치는 영향에 관한 연구 (A Study on the Effect of Atomization of Pressure Nozzle with Blower - Air)

  • 고경한;임상호
    • 디지털융복합연구
    • /
    • 제10권5호
    • /
    • pp.283-288
    • /
    • 2012
  • 본 연구는 이유체 분무장치 미립화 장치 분무특성을 연구하기 위해 수행되었다. 실험 조건은 상온에서 분사압력을 5 bar에서 10 bar 까지 1 bar 간격과 송풍기로부터 공기유량은 0.5, 1.0, 2.0 mmH2O(X10-2)로 증가하였으며, 사용된 액체는 경유이다. 분무특성을 연구하기위해 SMD를 측정하였다. 이 실험으로 부터 다음과 같은 결과를 얻었다. 1. 분무 압력이 증가할수록 SMD는 점점 감소한다. 2. 압력노즐로부터 측정 거리가 증가할수록 SMD도 증가한다. 3. 송풍공기가 더해지면서 분무되는 경우의 SMD는 상대적으로 감소한 것으로 볼 수 있다. 이 연구의 결과로 알 수 있듯이, 송풍공기가 더해지는 분사 장치는 유용한 SMD의 변화를 볼 수 있다. 이는 이유체 분무장치 미립화 장치 분무특성 설계와 성능평가를 위한 중요한 지표로 사용될 수 있을 것으로 판단된다.

로터리 킬른용 Low-NOx 다공노즐버너 개발을 위한 수치해석적 연구 (Numerical Study to Develop Low-NOx Multi-nozzle Burner in Rotary Kiln)

  • 안석기;김진호;황민영;김규보;전충환
    • 에너지공학
    • /
    • 제23권4호
    • /
    • pp.130-140
    • /
    • 2014
  • 공정효율 및 배기배출물 개선을 위해 로터리 킬른 버너 개발에 대한 연구는 지속적으로 이루어져 왔다. 본 연구에서는 COG(Coke Oven Gas)를 연료로 사용하는 철광석 소결용 로터리 킬른의 다공노즐버너 개발을 위해 일차공기 노즐 직경, 버너 당량비, 버너 중앙노즐과 주위노즐의 당량비 변화에 따른 화염 및 배기배출 특성에 대한 수치해석 연구를 수행하였다. 일차공기 노즐 직경이 증가함에 따라 각 동일 당량비에서 화염길이는 길어지고 $NO_x$ 배출도 증가하였으며, 버너 당량비가 증가함에 따라 화염길이와 $NO_x$ 배출이 증가하는 결과를 보였다. 버너 중앙노즐의 당량비 변화에 따라 $NO_x$ 배출에는 차이를 보였으며, 화염길이 및 킬른 내부 온도에는 큰 차이가 없었다. 본 연구를 통해 $D_2/D_1$가 1.33, 버너 당량비가 1.25이고 버너 중앙 노즐이 Rich인 조건이 킬른 내부 온도분포 및 $NO_x$ 배출량 기준을 만족하는 적절한 설계조건임을 제시하였다.