• Journal of the Korean Wood Science and Technology
• /
• 제18권2호
• /
• pp.8-15
• /
• 1990

This study was carried out to investigate the wood qualities for the end-use development of sycamore (Platanus occidentalis L.) grown in Korea. The results obtained were as follows: 1. The average length of wood fibers was l.56mm and the average width of annual rings was 9.5mm. It had very fast growth rate. 2. The specific gravity in air-dry was 0.66. The shrinkage and water absorption were relatively large. The shear and impact strengthes were very strong, while the compressive, tensile, and bending strengthes were weak in comparison to it's specific gravity. 3. The contents of ash, holocellulose, lignin were relatively high 0.74%, 83.08%, 28.79%, but that of pentosan was low 18.53%. 4. The expected uses of sycamore wood are plywood. fancy veneer, small furniture, musical instrument, door and window frame, tool handels, boxes, etc.

• Journal of Information Processing Systems
• /
• 제4권2호
• /
• pp.41-52
• /
• 2008

In this paper, we discuss a novel reservation-based, asynchronous MAC protocol called 'Multi-rate Multi-hop MAC Protocol' (MMMP) for multi-hop ad hoc networks that provides QoS guarantees for multimedia traffic. MMMP achieves this by providing service differentiation for multirate real-time traffic (both constant and variable bit rate traffic) and guaranteeing a bounded end-to-end delay for the same while still catering to the throughput requirements of non real time traffic. In addition, it administers bandwidth preservation via a feature called 'Smart Drop' and implements efficient bandwidth usage through a mechanism called 'Release Bandwidth'. Simulation results on the QualNet simulator indicate that MMMP outperforms IEEE 802.11 on all performance metrics and can efficiently handle a large range of traffic intensity. It also outperforms other similar state-of-the-art MAC protocols.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3357-3368
• /
• 1994

Total pressure losses required to calculate the total-to-total efficiency are estimated by integrating empirical loss coefficients of four loss mechanisms along the mean-line of blades as follows; blade profile loss, secondary flow loss, end wall loss and tip clearance loss. The off-design points are obtained on the basis of Howell's off-design performance of a compressor cascade. Also, inlet-outlet air angles and camber angle are obtained from semi-empirical relations of transonic airfoils' minimum loss incidence and deviation angles. And nominal point is replaced by the design point. It is concluded that relatively simple loss models and Howell's off-design data permit us to calculate the off-design performance with satisfactory accuracy. And this method can be easily extended for off-design performance prediction of multi-stage compressors.

• 한국소음진동공학회논문집
• /
• 제27권1호
• /
• pp.36-42
• /
• 2017

Helical gear excitation is transmitted to a gearbox through the shafts and bearings and the vibration of the gearbox radiates the noise in the air. Therefore gearbox modeling is essential to evaluate the gear noise. This work deals with vibration and acoustic analysis of a cylindrical shell-type gearbox with/without holes excited by helical gears and focuses on the development of the simple gearbox model. To do so, helical gears and bearing forces are calculated. Gearbox with/without holes is modeled by the aluminum end plates and PMMA cylindrical shell body. The vibration mode and the forced harmonic response were calculated by the commercial FE software and the end plate of the gearbox is more contributed to vibration than the body. Acoustic analysis was also conducted by the commercial acoustic software and a cylindrical shell type gearbox with/without holes has the similar vibro-acoustic characteristics.

• 오토저널
• /
• 제14권5호
• /
• pp.30-40
• /
• 1992

Spark knock obstructs any improvement in the efficiency and performance of an engine. As the knock mechanism of spark ignition engine, the detonation and the autoignition theory have been offered. In this paper, the knock model was established, which was able to predict the onset of knock and knock timing of spark ignition engine by the basis of autoignition theory. This model was a function of engine speed and equivalent air-fuel ratio. When this established knock model was tested from 1000rpm to 3000rpm of engine speed data, maximum error was crank angle 2 degrees between measured and predicted knock time. And the main results were as follows by the experimental analysis of spark knock in spark ignition engine. 1) Knock frequency was increased as engine speed increased. 2) Knock amplitude was increased as mass of end gas increased. 3) Knock frequency was occured above minimum 18% mass fraction of end gas.

• 한국자기학회지
• /
• 제4권2호
• /
• pp.106-113
• /
• 1994

초전도 반발식 자기부상열차의 동특성을 해석하기 위하여 외력에 의하여 대차가 기울어진 경우에 차량에 가해지는 전자력을 계산하였다. 집중부하방식의 열차에 있어서 크게 나타나는 단부효과 를 고려하기 위하여 공극자속의 형태에 대한 가정없이 자속분포를 계산하였으며, 대차의 옆질(roll), 뒷질(pitch) 및 편주(yaw)시의 전자력특성과 복원토오크를 검토하였다. 6개의 초전도자석이 탑재된 대 차가 차량의 양쪽에 설치된 열차에 대해서 계산한 결과, 토오크의 방향은 차량을 안정하게 하는 방향 으로 나타나서 본 자기부상시스템은 기본적으로 안정한 시스템임을 보여주고 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1203-1206
• /
• 2003

After the micro turning lathe was developed in the last year by AMR Laboratory, a micro-milling machine is developed for micro machining. This machine is integrated with PZT-driven micro-sliders, micro-linear encoders, air turbine spindle which has maximum 150.000 rpm. It is applicable to milling and drilling machining. This paper shows the possibility of micro machining and characteristics of micro end milling process by using micro machine. A machining of micro barrier ribs using 0.2 mm flat type end mill was achieved by micro-milling machine. As experimental results show the machining capability and positional accuracy of this machine is good enough for machining micro parts.

• 센서학회지
• /
• 제16권3호
• /
• pp.192-196
• /
• 2007

A fiber-optic interferometric temperature sensor is fabricated using a hollow optical fiber with 8 um air hole. This interferometric sensor for measuring temperature consists of 13 mm long hollow optical fiber whose one end is attached to the single mode fiber and the other end is cleaved. After the sensor is put in a furnace, the phase change of the sensor output signal is measured as the temperature of the furnace increases from $28^{\circ}C$ to $100^{\circ}C$. The phase change of the fiber sensor is proportional to the change of temperature and the relationship between the change of phase and temperature is approximately linear. The sensitivity of this sensor is $2.7{\;}radians/^{\circ}C$.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.354-362
• /
• 2000

In Korea, researches on year-round leaf vegetables production system are in progress, most of them focused on environmental control. Therefore, automation technologies for harvesting, transporting, and grading are in great demand. A robot system for harvesting lettuces, composed of a 3-DOF (degree of freedom) manipulator, an end-effector, a lettuce feeding conveyor, an air blower, a machine vision system, six photoelectric sensors, and a fuzzy logic controller, was developed. A fuzzy logic control was applied to determine appropriate grip force on lettuce. Leaf area index and height were used as input variables and voltage as an output variable for the fuzzy logic controller. Success rate of the lettuce harvesting was 94.12%, and average harvesting time was approximately 5 seconds per lettuce.

• Journal of Chest Surgery
• /
• 제26권6호
• /
• pp.501-504
• /
• 1993

Adenoid cystic carcinoma of the tracea is rare, but is a very serious critical life-threatening disease.Nearly all the lesions of the trachea are presented as obstructive lesions. Bronchoscopic examination including chest CT, tomogram and air tracheogram are essential for the further definition of these lesions. This is a case report of adenoid cystic carcinoma in a 47 years old male patient. The tumor was located in cervical trachea with wide base and obstructing the lumen almost completely. The patient`s symptom was productive cough and hoarseness for 4 months. The tumor was resected and End-to-End anastomosed. The tumor was confirmed to be adenoid cystic carcinoma histopathologically. The need for removal of tracheal tumor whether complete or incomplete, is clear enough regardless of the histology of the tumor. This patient was treated post-operatively with radiation.