• 전기학회논문지
• /
• 제62권7호
• /
• pp.1045-1052
• /
• 2013

In this study we deal with design procedures for the flywheel energy storage system that has the capacity to store the regenerative energy produced from the railway vehicles. The flywheel energy storage system (FESS) stores the regenerative electrical energy into the high speed rotational flywheel, by conversion the electrical energy into the mechanical rotational energy. Thus the FESS is composed of the energy conversion components, such as the motor and generator, mechanical support components, such as the rotational rotor, the magnetic bearings to support the rotor, and the digital controller to control the air gap between the rotor and the magnetic bearings. In this paper the design procedures for the rotor operating at the rigid mode and the magnetic bearings to support the rotational rotor without contact are presented.

• 제어로봇시스템학회논문지
• /
• 제22권11호
• /
• pp.925-931
• /
• 2016

The BLDC motor is used widely in industry due to its controllability and freedom from maintenance because there is no mechanical brush in the BLDC motor. Furthermore, it is suitable for high-speed applications, such as compressors and air blowers. For instance, for a compressor with a small impeller due to miniaturizing, the BLDC motor has to rotate at a very high speed to maintain the compression ratio of the compressor. Typically, to reach an ultra-high speed, airfoil bearings must be used in place of ball bearings because of their friction. Unfortunately, the characteristics of airfoil bearings change drastically depending on the revolution speed. In this paper, a BLDC motor with airfoil bearings is controlled with a PID controller. To analyze and determine the PID coefficients, the relay-feedback method is used. Additionally, for adaptive control, a fuzzy logic controller is used. Furthermore, the auto-tuning and self-tuning techniques are combined to control the BLDC motor. The proposed method is able to control the airfoil-bearing BLDC motor efficiently.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권3호
• /
• pp.241-247
• /
• 2014

The voltage source PWM inverter generally used to drive the air conditioning (A/C) fans has been posing a large issue that the bearings in air conditioning fan motors are highly possible to be corroded electrically. Potential difference called shaft voltage is generated between inner and outer rings of the bearings due to inverter switching. The shaft voltage causes bearing lubricant breakdown dielectrically. As a result, bearing current is caused. This current causes the bearing corrosion. In previous work, we demonstrated that the shaft voltage can be reduced by using an insulator inserted between the outer and inner cores of the rotor in an air conditioning fan motor without grounding. This paper proposes the other countermeasure for reducing the shaft voltage in fan motors. The countermeasure which adds a capacitor between the brackets and the stator core is effective even for fan motors with non-insulated rotor. The effectiveness is confirmed by both simulated and experimental results.

• 한국자동차공학회논문집
• /
• 제16권4호
• /
• pp.47-55
• /
• 2008

Turbocharger has a main purpose on recycling of the exhaust gas from the engine cylinder. On the basis of the facility characteristics, the turbocharger supported on floating ring bearings has some problems such as the large volume, oil supplement for lubrication and high power loss due to high operating torque. The air foil bearing has been studied as the bearing element to be able to alternate the floating ring bearing without the problems of the floating ring bearing. In this study, the air foil bearing has 2 parts; journal and thrust bearings, and the test facility consists of the engine, exhaust and intake parts. In addiction, the specification of the turbocharger follows a small turbocharger for SUV engine. The engine speed is varied from 750 (idle rpm) to 2,500 rpm and then, the rotating speed of the turbocharger rotor is accelerated from 0 to 100,000 rpm. From those experiments, the comparison between the performances of the air foil bearing and floating ring bearing is conducted and the results show that the air foil bearing has less power loss, maximum 770 watt, than the floating ring bearing, maximum 5,110 watt. This result verifies that the air foil bearing is more efficient and able to output more power under the same condition of the input power.

• 한국산학기술학회논문지
• /
• 제12권12호
• /
• pp.5412-5419
• /
• 2011

산업의 발달에 따른 각종기기 장치들의 고속화, 소형화, 정밀화로 인해 고속 스핀들의 필요성은 점점 커지고 있다. 또한 공기동압베어링은 스테이지 모션에 대해서 무마찰 실현을 위해서 웨이퍼 생산용 광학 리소그래피 분야에도 적용된다. 공기동압베어링은 마찰에 의한 동력손실과 열 발생이 적어 고속회전에 유리하고 고정밀 회전이 가능하기 때문에 고속 고정밀 스핀들 시스템 및 하드 디스크 드라이브에 사용될 수 있다. 본 연구에서는 축 하중 지지를 위해 헤링본 홈 형상을 가지는 공기동압베어링의 성능에 대한 수치해석을 수행하였다. 또한 본 연구에서는 공기동압베어링을 제작하기 위해서 기존의 기계 가공방법과는 다른 비접촉식 초정밀 가공 방법인 마이크로 전기화학가공에 의한 방법으로 마이크로 그루브 가공을 수행하였고, 수치해석 프로그램을 이용하여 전극의 간극, 전해용액 농도, 가공시간 등 이론적인 수치를 시뮬레이션 하였다.

• Tribology and Lubricants
• /
• 제40권1호
• /
• pp.17-23
• /
• 2024

This study analyzes the thermal effects on the performance of an air foil thrust bearing (AFTB) using COMSOL Multiphysics to approximate actual bearing behavior under real conditions. An AFTB is a sliding-thrust bearing that uses air as a lubricant to support the axial load. The AFTB consists of top and bump foils and supports the rotating disk through the hydrodynamic pressure generated by the wedge effect from the inclined surface of the top foil and the elastic deformation of the bump foils, similar to a spring. The use of air as a lubricant has some advantages such as low friction loss and less heat generation, enabling air bearings to be widely used in high-speed rotating systems. However, even in AFTB, the effects of energy loss due to viscosity at high speeds, interface frictional heat, and thermal deformation of the foil caused by temperature increase cannot be ignored. Foil deformation derived from the thermal effect influences the minimum decay in film thickness and enhances the film pressure. For these reasons, performance analyses of isothermal AFTBs have shown few discrepancies with real bearing behavior. To account for this phenomenon, a thermal-fluid-structure analysis is conducted to describe the combined mechanics. Results show that the load capacity under the thermal effect is slightly higher than that obtained from isothermal analysis. In addition, the push and pull effects on the top foil and bump foil-free edges can be simulated. The differences between the isothermal and thermal behaviors are discussed.

• 대한기계학회논문집A
• /
• 제39권10호
• /
• pp.1029-1037
• /
• 2015

최근 회전 시스템의 고속화 경향에 따라 회전체 동역학적 안정성의 중요성이 부각되었다. 고속회전 시스템에 적용되는 가스베어링의 동특성을 규명하는 것은 회전체의 거동을 예측하는데 상당히 중요하다. 본 연구에서는 대표적인 가스베어링인 가스포일베어링의 범프 구조에 대하여 가진실험을 수행하고 가진 주파수에 따른 동특성을 측정하였다. 실험 결과, 범프 구조의 강성은 주파수에 따라 증가하였고 감쇠는 감소하였다. 또한, 가압 조건에서의 동특성은 범프 구조의 동특성 보다 낮은 값을 가졌다. 본 실험을 통해 범프 구조의 주파수 의존 동특성의 경향을 파악하였으며 가스포일베어링의 동특성에 윤활막이 미치는 영향에 대해 확인하였다. 또한 두 가지 동특성 계산 방법을 제시하여 실험결과를 통해 효과 적인 동특성 계산 방법에 대해 비교 고찰하고 범프 구조와 윤활막의 동특성을 비교 하였다.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.44-51
• /
• 2019

The paper presents the rotordynamic performance measurements and model predictions of a fuel cell electric vehicle (FCEV) air compressor supported on gas foil bearings (GFBs). The rotor has an impeller on one end and a thrust runner on the other end. The front (impeller side) and rear (thrust side) gas foil journal bearings (GFJBs) are located between the impeller and thrust runner to support the radial loads, and a pair of gas foil thrust bearings are located on both sides of the thrust runner to support the axial loads. The test GFJBs have a partial arc shim foil installed between the top foil and bump strip layers to enhance hydrodynamic pressure generation. During the rotordynamic performance tests, two sets of orthogonally installed eddy-current displacement sensors measure the rotor radial motions at the rotor impeller and thrust ends. A series of speed-up and coast-down tests to 100k rpm demonstrates the dominant synchronous (1X) rotor responses to imbalance masses without noticeable subsynchronous motions, which indicates a rotordynamically stable rotor-GFB system. Finite element analysis of the rotor determines the rotor free-free (bending) natural modes and frequencies well beyond the maximum rotating frequency. The predicted damped natural frequencies and damping ratios of the rotor-GFB system reveal rotordynamic stability over the speeds of interest. The imbalance response predictions show that the predicted critical speeds and rotor amplitudes strongly agree with the test measurements, thus validating the developed rotordynamic model.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.232-232
• /
• 2004

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.239-243
• /
• 1997

The heat generation is the most important problem in the motor integrated spindle. Double cooling jacket in necessary to reduce the thermal displacement and to get the stable temperature disribution for the housing. In this study, the effects of temperature distribution and thermal displacement for the spindle system according to the variation of cooling oil flow rate are investigated experimentally on the motor-integrated spindle with double cooling jacket system. The experimental spindel system is composed with the angular contact steel ball bearings, oil-air lubrication, air or oil jacket cooling system.