• Journal of the Korean Chemical Society
• /
• v.64 no.5
• /
• pp.259-266
• /
• 2020

The main purpose of this study is to examine the different physicochemical properties of spray-dried products. The carrier agents and powders after the spray-drying process were analyzed for encapsulation yield, moisture content, color parameters, total polyphenol content (TPC), antioxidant capacity (AC), bulk density, flowability, wettability, hygroscopicity, water solubility index (WSI), particle size and microstructure. The spray-drying process was carried out with different carrier agents including maltodextrin (MD) and the combination of maltodextrin and gum arabic (MD-GA) with MA/GA ratio of 70/30, dried at the inlet/outlet air temperature of 160 ℃/70 ℃, 4 bar, airflow rate of 70 ㎥·h^-1 and feed flow rate of 750 mL·h^-1. The results showed that the different carrier agents have significant influences on the physicochemical properties of the powder produced by the spray-drying method. In there, while the values of recovery efficiency and flowability of spray-dried products from MD are higher than those of spray-dried products from MD-GA combination, the opposite is true for the values of TPC, AC, bulk density and wettability, whereas hygroscopicity and WSI values are equally represented in both products.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.168-175
• /
• 2006

An experimental study was conducted to investigate the effect of the morphology of CNT on the thermal conductivity of suspensions. The effective thermal conductivities of the samples were measured using asteady-state cut bar apparatus method. Enhancements based on the thermal conductivity of the base fluid are presented as functions of both the volume fraction and the temperature, Although functionalized SWNT produiced a more stable and homogeneous suspension, the addition of small amounts of surfactant to suspensions of 'as produced' SWNT demonstrated a greater increase in effective thermal conductivity than functionalized SWNT alone. The effective thermal conductivity enhancement corresponding to 1.0 percent by volume approached 10%, which was observed to be lower than expected, but more than twice the values, 3.5%, obtained for similar tests conducted using aluminum oxide suspensions. However, for suspensions of MWNT, the degree of enhancement was measured to be approximately 37%. It was postulated that the effect of clustering, resulting from the multiple heat-flow passages constituted by interconnecting neighboring CNT clusters, played an important role in significant enhancement of effective thermal conductivity.

• Transactions of Materials Processing
• /
• v.28 no.5
• /
• pp.266-274
• /
• 2019

Metal sealing is used to connecting the parts between valves and fuel pipes for a FCEV which utilizes hydrogen gas of 700 bar. Instead of general carbon steel, stainless steel is the primary material used to manufacture fuel pipes due to hydrogen embrittlement. The shape of deformation between metals is an important factor on the air-tightness of the metal to metal contact. Since the stainless steel pipe is hardened using the plastic forming during the tip shaping stage, this work hardening could have an effect on the deformed shape and characteristics of contact surfaces in fastening of pipes. In this paper, the deformation history of the pipe model was considered in order to analyze the hydrogen-tightness on the metal sealing part. The contact distance and the forward displacement for fastening were compared using experimental results and the simulation results. The simulation of the effect of material change on the fitting body demonstrated that the hardness or the strength of the formed tip of the pipe was designed to a proper valued level since the characteristics of the contact surface was exhibited better when the strength of the pipe was lower than that of the fitting body.

• Journal of the Korean earth science society
• /
• v.42 no.3
• /
• pp.278-295
• /
• 2021

China's shutdown due to COVID-19 in 2020 reduced air pollutant emissions, which is located on the windward side of South Korea. The positive temperature anomaly and negative zonal wind anomaly from northern Mongolia to South Korea through eastern China presented warm and stationary air masses during January and February 2020. Decreased concentrations of PM10, NO₂, and O₃ were measured at Seokmo-ri and Pado-ri, located in the central-western region of South Korea, due to decreased emissions in China from January to March 2020. After China's shutdown from January to March 2020, in Pado-ri, the ratio of monthly average concentrations in that period with those of PM10 and O₃ in the last four years decreased by approximately 0.7-4.7% and 9.2-22.8%, respectively. In January 2020, during the Lunar New Year holidays in China, concentrations of PM10, NO₂, and O₃ at Seokmo-ri and Pado-ri decreased just as much as it did during the same period in the last four years. However, average concentrations in January 2020 decreased before and after the Lunar New Year holidays in China when compared with those in January of the last four years. In Seokmori, ratios of actual and predicted values (${\bar{O}_s$/M) for PM10, NO₂, and O₃ concentrations were calculated as 70.8 to 89.7%, 70.5 to 87.1%, and 72.5 to 97.1%, respectively, during January and March 2020. Moreover, those of Pado-ri were 79.6 to 93.5%, 67.7 to 84.9%, and 83.7 to 94.6%, respectively. In January 2020, the aerosol optical depth (AOD) data showed a higher distribution than that of the last four years due to photochemical reactions in regions from northern Mongolia to eastern China and the Korean Peninsula. However, the decrease in AOD values compared with those of the last four years was attributed to the decrease in emissions of precursors that generate secondary aerosols in China during March 2020.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.4
• /
• pp.233-252
• /
• 2021

This paper is a study to improve the efficiency of mixing technology in the shield TBM chamber. Currently, the number of construction cases using the TBM method is increasing in Korea. According to the increasing use of TBM method, research on TBM method such as Disc Cutter, Cutter bit, and Segment also shows an increasing trend. However, there is little research on the mixing efficiency in chamber and chamber. In order to improve the smooth soil treatment and the behavior of the excavated soil, a study was conducted on the change of the mixing efficiency according to the effective mixing bar arrangement in the chamber. In the scale model experiment, the ground was composed using plastic materials of different colors for ease of identification. In addition, the mixing bar arrangement was different and classified into 4 cases, and the particle size distribution was classified into single particle size and multiple particle size, and the experiment was conducted with a total of 8 cases. The rotation speed of the cutter head of all cases was the same as 5 RPM, and the experiment time was also carried out in the same condition, 1 minute and 30 seconds. In order to check the mixing efficiency, samples at the upper, middle (left or right), and lower positions of each case were collected and analyzed. As a result of the scaled-down model experiment, the mixing efficiency of Case 4 and Case 4-1 increased compared to Case 1 and Case 1-1, which are actually used. Accordingly, it is expected that the mixing efficiency can be increased by changing the arrangement of the mixing bar in the chamber, and it is considered to be effective in saving air as the mixing efficiency increases. Therefore, this study is considered to be an important indicator for the use of shield TBM in Korea.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.15 no.2
• /
• pp.49-54
• /
• 2009

The effects of filling temperatures of broth and degassing method on the residual oxygen content and gas composition in the pouch and physical strength of packaging material for Samgyetang depending on the contamination of broth on the sealing layer and sterilization process were investigated. The residual oxygen content in the broth and the oxygen proportion in the headspace of package were decreased with the increase of broth temperature at filling into the pouch from 50 to 100. When the products were packaged as air-contained (Air), manually squeezed the upper side of package out to minimize the headspace (Degas) and flushed with nitrogen gas ($N_2$-Flushing) while maintaining the broth temperatures of Samgyetang at 50 or 85. The residual oxygen content and oxygen proportion were increased in the order of $N_2$-Flushing

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.3
• /
• pp.155-163
• /
• 2017

Membrane filtration has become more popular in drinking water treatment recently, since the filtration can control not only particulate matters but also pathogenic microorganisms such as giardia and cryptosporidium very effectively. Pilot-scale ($120m^3/d$ of treatment capacity) and test-bed ($25,000m^3/d$ of treatment capacity) microfiltration experiments were conducted to find optimum operating mode and the critical flux. Optimum operating mode of pilot-test was assessed as inflow 1.0 min, filtration 36.5 min, air backwash 0.9 min, backwash 1.0 min and outflow 1.0 min with 50 LMH ($L/min{\cdot}m3^$) of critical flux. Critical Flux was calculated to be $50L/m^2-h$ (within TMP 0.5 bar) based on the increase formula of the transmembrane pressure difference according to the change of time at Flux 20, 40, 56 and 62 LMH in pilot operation. Chemical cleaning was first acid washed twice, and alkali washing was performed secondarily, and a recovery rate of 95% was obtained in the test-bed plant. The results of operating under these appropriate conditions are as follows. Turbidity of treated water were 0.028, 0.024, 0.026 and 0.028 NTU in spring, summer, autumn and winter time, respectively. Microfiltration has superior treatment capability and performance characteristics in removing suspended solids and colloidal materials, which are the main cause of turbidity and important carrier of metal elements, and it has shown great potential in being an economically substitute to traditional processes (sand filtration).

• Journal of the Korean Electrochemical Society
• /
• v.4 no.4
• /
• pp.172-175
• /
• 2001

Nanophase catalyst layer for direct methanol fuel cell has been fabricated by magnetron sputtering method. Catalyst metal targets and carbon were sputtered simultaneously on the Nafion membrane surface at abnormally higher gas (Ar/He mixture) pressure than that of normal thin film processing. They could be coated as a novel structure of catalyst layer containing porous PtRu or Pt and carbon particles both in nanometer range. Membrane electrode assembly made with this layer led to a reduction of the catalyst loading. At the catalyst loading of 1.5mg $PtRu/cm^2$ for anode and 1mg $Pt/cm^2$ for cathode, it could provide $45 mW/cm^2$ in the operation at 2 M methanol, 1 Bar Air at 80"C. It is more than $30\%$ increase of the power density performance at the same level of catalyst loading by conventional method. This was realized due to the ultra fine particle sizes and a large fraction of the atoms lie on the grain boundaries of nanophase catalyst layer and they played an important role of fast catalyst reaction kinetics and more efficient fuel path. Commercialization of direct methanol fuel cell for portable electronic devices is anticipated by the further development of such design.

• Journal of the Korean Applied Science and Technology
• /
• v.36 no.4
• /
• pp.1281-1289
• /
• 2019

This study was conducted to evaluate the optimal operating condition of ultra-fine bubble washing machine for removing calcium chloride from road concrete structure. The diameter of the ultra-fine bubble was measured to 196.6 ± 100.6 nm and the ultra-fine bubble concentration was measured to 1.36 × 108 cell/ml. As a result of the performance on the spray device of the washing machine, it was confirmed that the washing efficiency of 93% and 91% appeared at 100cm and 150cm of injection distance at 100bar injection pressure. By increasing the ultra-fine bubble generation cycles from 2 to 6, the chloride removal rate increased from 1% to 7%. As the ultra-fine bubble generation air flow was lowered from 4 ml/min to 0.5 ml/min, it was confirmed that the washing efficiency increased up to 30%. The washing efficiency of ultra-fine bubble water was 25% higher than normal water.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.465-473
• /
• 2018

A cabinet-door integrated finite element model for a built-in side-by-side refrigerator with an ice dispenser and home bar was constructed, and its deformation was analyzed by ANSYS. As loads, the food load in the shelf and baskets, and thermal load occurring during the normal operation condition were considered. From results of the analyses, the door height difference (DHD) and door flatness difference (DFD) between the two doors, and the increase in the gap of the door gasket, which affects the sealing of cool air in the cabinet, were derived. As results of an evaluation of the differences, the DHD and DFD under the assembled condition satisfied the acceptance criteria of the manufacturer. The food and thermal loads increased the DHD and DFD due to thermal deformation, and the DFD increased significantly. In addition, the increase in the gap of door gasket located between the cabinet and doors was derived from the results of displacements under the food and thermal loads. The evaluation showed that the maximum increase in gap appeared at the left edge of the freezing compartment gasket, which satisfied the acceptance criteria of the manufacturer.