• 한국군사과학기술학회지
• /
• 제21권1호
• /
• pp.47-60
• /
• 2018

In this paper, we proposed a method for eliminating aiming error of unguided anti-tank rocket using improved target tracking. Since predicted fire is necessary to hit moving targets with unguided rockets, a method was proposed to estimate the position and velocity of target using fire control system. However, such a method has a problem that the hit rate may be lowered due to the aiming error of the shooter. In order to solve this problem, we used an image-based target tracking method to correct error caused by the shooter. We also proposed a robust tracking method based on TLD(Tracking Learning Detection) considering characteristics of the FCS(Fire Control System) devices. To verify the performance of our proposed algorithm, we measured the target velocity using GPS and compared it with our estimation. It is proved that our method is robust to shooter's aiming error.

• 한국소음진동공학회논문집
• /
• 제15권11호
• /
• pp.1303-1310
• /
• 2005

Stabilization error of target aiming systems mounted on moving vehicles is an important performance because the error directly affects hit Probability. In a heavy load targetaiming system, the disturbance torque comes from mass unbalance and linear acceleration is a main source of stabilization error. This study suggests an experimental design method of disturbance feedforward compensation control to improve the stabilization performance of heavy load target aiming systems. The filtered_x least square(FxLMS) algorithm is used to estimate the compensator coefficients adaptively. The proposed control is applied to a simple experimental set-up which simulates dynamic characteristics of a real target aiming system. The feasibility of the proposedtechnique is illustrated, along with results of experiments.

• 대한기계학회논문집
• /
• 제2권2호
• /
• pp.47-51
• /
• 1978

In order to improve the hitting rate in the shot of rifles, it is required that the analysis of exterior ballistics and the line of sight. One of the important factors influenced a marksman using a rifle obtained the zero-setting of a rifle at the horizontal range, is the deviation of the impact point from the aiming point when the shooting is performed in an inclined ranges. The deviation usually cccurs from the reaction force along the bore line, the characteristics of exterior ballistics, and the error of a shooting range judgement by the inclined range. This study is concerned with the problem of the vertical difference between the impact and aiming point in the inclined shooting ranges. The computing method to find the vertical difference is represented. This method is applied for and experimental rifle in three cases, (1) hofizontal shooting ranges, (2) upper inclined shooting ranges, and (3) lower inclined shooting ranges.

• 한국군사과학기술학회지
• /
• 제7권3호
• /
• pp.30-37
• /
• 2004

For a proper operation of portable air defense IR terminal homing missile to the rapid intruding target, the boresight of an IR seeker of the missile should be accurately aligned with the gunner's aiming sight. Before a gunner fires the missile, he tries to keep the target within the circle of ASU ensuring the seeker to lock on the target correctly. In this paper, using an electrical seeker caging loop and IR detector signal characteristics, a precise aligning method between the seeker boresight and the LOS(Line of Sight) of ASU(Aiming Sight Unit) was studied. Although every seeker has slightly different SLA (Signal of Look Angle) output, we can get negligible alignment error through a fine tuning method of electrical caging signal. This alignment procedure was also adopted in K-PSAM system.

• 한국CDE학회논문집
• /
• 제19권4호
• /
• pp.340-346
• /
• 2014

There are many factors that contribute to hit probability of the gun shot of ground combat vehicles. Aiming accuracy is mainly affected by the dynamic state of the vehicle. The stabilization error of the turret under system vibration is one of the major factors that affect the aiming accuracy. The vibration of the vehicle is affected by both the state of the road and the speed of the vehicle. This paper analyzes the aiming accuracy of the gun equipped on the GCV when the vehicle drives on the different roads and at different speed. The vertical displacement and the pitch angle of the gun are calculated and the impact points of the target are calculated. Distribution of the impact points on the target is greatly influenced by the pitch rotation rather than vertical displacement. And this aiming errors result in the errors of point of impacts on the target after the bullet flies through the air under trajectory equations. The GCV is modeled using a half-car model with 6 D.O.F. and the specifications of the M2 machine gun are used in trajectory calculation simulation and the target is located in 1000 m away from the gun.

• ETRI Journal
• /
• 제29권5호
• /
• pp.596-606
• /
• 2007

It is well known that an OFDM receiver is vulnerable to synchronization errors. Despite fine estimations used in the initial acquisition, there are still residual synchronization errors. Though these errors are very small, they severely degrade the bit error rate (BER) performance. In this paper, we propose a residual error elimination scheme for the digital OFDM baseband receiver aiming to improve the overall BER performance. Three improvements on existing schemes are made: a pilot-aided recursive algorithm for joint estimation of the residual carrier frequency and sampling time offsets; a delay-based timing error correction technique, which smoothly adjusts the incoming data stream without resampling disturbance; and a decision-directed channel gain update algorithm based on recursive least-squares criterion, which offers faster convergence and smaller error than the least-mean-squares algorithms. Simulation results show that the proposed scheme works well in the multipath channel, and its performance is close to that of an OFDM system with perfect synchronization parameters.

• ETRI Journal
• /
• 제27권1호
• /
• pp.53-63
• /
• 2005

A compressed video bitstream is sensitive to errors that may severely degrade the reconstructed images even when the bit error rate is small. One approach to combat the impact of such errors is the use of error concealment at the decoder without increasing the bit rate or changing the encoder. For spatial-error concealment, we propose a method featuring edge continuity and texture preservation as well as low computation to reconstruct more visually acceptable images. Aiming at temporal error concealment, we propose a two-step algorithm based on block matching principles in which the assumption of smooth and uniform motion for some adjacent blocks is adopted. As simulation results show, the proposed spatial and temporal methods provide better reconstruction quality for damaged images than other methods.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.175-178
• /
• 2000

An aerostatic stage has frictionless behavior, so it has a advantage of investigation into positioning characteristics. A one-dimensional aemstatic ceramic stage with ballscrew driven and laser scale feedback system is manufactured. aiming at investigating positioning characteristic of aerostatic stage, especially position error and repeatability, we analyze positioning behavior with other factors such as angular error, temperature. Experimemal results show that the aerostatic stage has a l0nm micro step response. Comparing experimental results and calculated abbe's error, we confirm that mean of position error is owing to angular error. And, also we confirm the temperature is dominant factor of repeatability in ten nm order.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.378-391
• /
• 2002

A 250mm stroke aerostatic stage, which detects position with laser scale and is driven by linear motor, is made and analyzed positioning error in 20$\pm$ 0.5 $^{\circ}C$ controlled atmosphere, aiming at investigating positioning characteristic of ultra-precision stage. We prove this aerostatic stage has a 10nm micro step resolution by experiment. By means of analyzing laser interferometer system, the scale of measuring error is about 0.2-0.4$\mu\textrm{m}$ according to refractive index error from missing the temperature change. To improve laser interferometer system, compensate refractive index error using measuring data from thermocouple. And, confirm 0.10$\mu\textrm{m}$ repeatability and 0.13 $\mu\textrm{m}$ positioning accuracy using the compensating refractive index. Also, we confirm 0.07 ${\mu}{\textrm}{m}$ repeatability of the stage using capacitive displacement sensor.

• 전자공학회논문지CI
• /
• 제40권5호
• /
• pp.241-249
• /
• 2003

십진수를 위한 가산기 구현에서 지연시간을 줄일 수 있는 carry lookahead(CLA)을 이용한 십진수 가산 회로 선계를 제안한다. 이자 계산과 같은 십진 소수에 의한 반복계산에서 이진수 체계를 사용하면 절단오차는 누적된다. 이를 방지하기 위하여 BCD 회로 사용은 불가피하다. BCD 계산에서의 속도개선은 CLA 회로를 이용하여 개선될 수 있다. BCD 회로에서 CLA 회로 사용을 위해 제안된 캐리 생성 및 캐리 전파회로를 도출하여 가산기 설계에 사용하였다. 이 CLA 방식을 사용한 BCD 가산에서 기존의 BCD 가산회로와 지연시간을 비교하였을 때 상당한 속도개선이 이루어졌다. 또한 3초과 코드를 이용한 가산회로의 경우 CLA 방식 사용과 지연시간에 영향을 미치는 회로부분을 개선함으로써 CLA만 이용했을 때 보다 지연시간을 10게이트 지연시간만큼 더욱 줄일 수 있었다.