• Journal of Biosystems Engineering
• /
• 제37권5호
• /
• pp.287-295
• /
• 2012

Purpose: Some of the most representative approaches are to apply next generation technologies to save energy consumption, fully automated control system to appropriately maintain environmental conditions, and autonomous assistance system to reduce labor load and ensure operator's safety. Nevertheless, improvement of upcoming method for soil cultured greenhouse has not been sufficiently achieved. Geometrical complexity of ground in protected crop cultivation might be one of the most dominant factors in design of autonomous vehicle. While there is a practical solution fairly enough to promise an accurate travelling, such as autonomous sprayer guided by rail or induction coil, for various reasons including the limitation of producer's budget, the previously developed sprayer has not been widely distributed to market. Methods: In this study, we developed an autonomous sprayer considering travelling performance on geometrical complexity of ground in soil cultured greenhouse. To maintain a stable travelling and to acquire a real time feedback, common wire with 80 mm thick and body frame and sprayer boom. To evaluate performance of the prototype, tracking performance, climbing performance and spraying boom's uniform leveling performance were individually evaluated by corresponding experimental tests. Results: The autonomous guidance system was proved to be sufficiently suitable for accurate linear traveling with RMS as lower than approximately 10 cm from designated path. Also the prototype could climb $10^{\circ}$ of ground's slope angle with 40 kg of water weight. Uniform leveling of spraying boom was successfully performed within $0.5^{\circ}$ of sprayer boom's slope. Conclusions: Considering more complex pathways and coarse ground conditions, evaluations and improvements of the prototype should be performed for promising reliability to commercialization.

• Journal of Biosystems Engineering
• /
• 제41권3호
• /
• pp.161-169
• /
• 2016

Purpose: To improve the insufficient mechanized forage harvesting system, an integrated forage harvester that produces midsize round bales was developed. Methods: The harvesting performance of the developed harvester was tested in a forage plantation. The harvesting performance was evaluated by investigating the bale production performance and residue ratios of the harvester at three levels of tractor driving speeds. Results: The bales outputs per hour by driving speed shown by the harvester were 30 bales (6.8 MT) at 2.3 km/h, 36 bales (8.4 MT) at 3.2 km/h, and 44 bales (10.5 MT) at 5.1 km/h in the case of rye-straw. In the case of rice-straw, they were 43 bales (8.8 MT) at 4.3 km/h, 44 bales (9.7 MT) at 5.0 km/h, and 48 bales (10.7 MT) at 6.2 km/h. In the case of Italian ryegrass (IRG), they were 35 bales (10.7 MT) at 7.0 km/h, 37 bales (12.0 MT) at 8.3 km/h, and 38 bales (13.2 MT) at 9.5 km/h. The average ratios of residues to the available quantities were 2.61% in the case of rye-straw, 1.89% in the case of rice-straw, and 1.57% in the case of IRG. When residues smaller than 200 mm, which cannot be collected, were excluded, the residue ratios of all crops were good, as they did not exceed 1.0%. Conclusions: Since the baling and wrapping functions, which had been separately operated, were integrated into the developed harvester, the developed harvester is expected to maximize bale production efficiency and increase labor productivity, thereby increasing farming profitability.

• Journal of Biosystems Engineering
• /
• 제41권3호
• /
• pp.201-207
• /
• 2016

Purpose: A water-spraying type automatic glochids removal system for cactus (Opuntia humifusa) stem was developed, and its performance was evaluated. The system was developed to reduce intensive human labor in removing glochids from cactus stem skin without inducing damage prior to further processing into value-added products. Methods: The developed system consists of conveyor and water-spraying systems. The conveyor system delivers cactus stems through water-spraying compartments and finally to a collecting box. In order to remove the glochids, rotating nozzles spray water over all areas (i.e., front and back faces and sides) of the cactus skin under controlled water pressure. Operating conditions such as conveyor speed, water pressure, angle of water-spraying nozzles, distance between conveyor belt and rotating nozzles, and angle of cactus flipping slide were adopted from our previous study and applied on the system design and manufacturing. The performance of glochids removal was evaluated by counting the number of glochids on the cactus stem before and after processing on the system. Results: The developed system performed efficiently and effectively under the pre-studied operating conditions except for the angle of cactus flipping slide. The new system had a glochids removal ratio of 94.1% without damaging the cactus skin. Considering the original number (approximately 30-60) of glochids, the remaining number was low (1-4), and most of them were found at the side edge of the cactus stem. This system can remove glochids from 360 cactus stems in 1 hr regardless of cactus size. Conclusions: The performance of the new system in glochids removal without damaging cactus skin is superior to any other existing device (i.e., brush type, rubber-friction type, and agitation type). The system is expected to be applied in cactus (O. humifusa) processing facilities.

• Journal of Biosystems Engineering
• /
• 제42권4호
• /
• pp.283-292
• /
• 2017

Purpose: Japanese Apricot, a type of plum, has various medicinal and economical applications. Plums are quite popular worldwide, but their deseeding remains a serious impediment to their processing. Therefore, a plum (Japanese Apricot) seed remover (PSR) was developed that can use various types of cutters according to the purpose of the plum processing, and its performance was evaluated. Methods: The proposed PSR, which allows multipurpose cutters, namely, zero-, two-, and four-blade cutters, to be installed, was first designed and manufactured. To identify appropriate parameters related to the cutting pressure, plums were harvested from three regions during three harvesting periods, and their geometrical and mechanical properties were measured. After application of the parameters related to the cutting pressure, a performance test was carried out on both fresh and frozen plums by identifying the ratios of the flesh recovery, seed recovery, seed breakage, deseeding efficiency, and machine efficiency. Results: The results show that, using the proper calculation of the processing parameters, 100% deseeding efficiency was facilitated regardless of the type of cutter used. However, in the case of a four-blade cutter, there are significant differences in the flesh recovery ratio according to the plum setting angle. Between the fresh and frozen plums, all cutters showed a significantly better flesh recovery ratio for the case of fresh plums. Conclusions: This machine will advance the plum processing technology, and eventually help the plum industry flourish.

• 한국작물학회지
• /
• 제43권1호
• /
• pp.49-53
• /
• 1998

Direct-seeding has major advantages such as labor and cost saving by eliminating preparation of seed bed and transplanting. But, it required increased input of fertilizers and pesticides because of the extended paddy period. Direct seeding in wet paddy (DSWP) gives faster growth and more uniform seedling emergence than direct-seeding in dry paddy. This research had an objective to develop an efficient N management practices for DSWP with split application of N fertilizer. A paddy field experiment was conducted to evaluate effects of starter N and N-topdressing which was delayed N application until 5-leaf stage, with comparison to transplanting (TP). Total amount of N application were two levels; 110kg and 77kg/ha. The N applications were split four times during rice growth stages; starter, topdressing at 5-leaf stage, top dressing at tillering stage, and topdressing at panicle initiation stage. DSWP had more tillers/$m^2$ than TP, but with the delayed heading. The DSWP plots which received N-topdressing at 5-leaf stage without starter N had higher leaf area index (LAI) and leaf greenness than the TP plot. Also, these DSWP plots had high leaf-N concentration at the heading stage, as calculated from leaf chlorophyll meter readings. Rice yield in DSWP with N-topdressing at 5-leaf stage was significantly higher than that in TP and in DSWP with starter N. Energy and N use efficiency were improved in DSWP with N-topdressing at 5-leaf stage. But, there were no significant differences in grain yield between the two levels of total amounts of N applications, 77kg and 110kg/ha. We concluded that starter N could not be used effectively by rice seedlings, but topdressing N at 5-leaf stage was an efficient N management for rice growth and yield in DSWP system.

• Journal of Biosystems Engineering
• /
• 제36권3호
• /
• pp.195-203
• /
• 2011

Not only does the labor of manufacturers used most in the drying process after rice harvest, but it also is having huge influence in quality. Also, because drying storage of rice production around the whole country is scarce with original facility, it has become a very important matter that farms develop their own safe and high-quality facilities to store and dry rice. Therefore, this study developed a small scale accumulated storage and drying bin, assessed nalyzed drying properties, and conducted analysis of research on the property of quality when storing for a long time. As a result, the drying speed of the small scale accumulated storage and drying bin was adequate of 0.042%/hr and was shown that the experimental static pressure and theoretical static pressure corresponded. Also, it was shown that drying cost was up to about 6 times inexpensive that heated air drying. For the storage of the small scale accumulated storage and drying bin, average of moisture content was around 16.5 until early April and decreased to 15.7% in July. Inside storage was maintained to 12.13% until early April and slightly increased to 14% after May. It was shown that inside storage had higher hardness and rate of cracking than the small scale accumulated storage and drying bin by storage conditions and germination rate was shown a little higher when stored in the small scale accumulated storage and drying bin.

• 한국자원식물학회지
• /
• 제4권2호
• /
• pp.67-74
• /
• 1991

동양에서는 생약을 주로 한약조제에 많이 이용되고 있으나 서양에서는 신의약품 개발과 제조에 이용되고 있다. 그러나 최근에 와서는 국내외를 막론하고 제약업계에서 양약의 제조와 신의약품 개발에 치중하여 생약의 수요가 증가하고 있다. 따라서 당국에서는 계획생산에 대한 지도와 자금지원, 품종관리, 재배 및 신의약품개발에 대한 연구지원, 수입통제에 의한 농민보호등 제도적 지원을 강화하여 우리나라 주종 재배약초의 자포자기적인 생산기피현상을 막아야 할 것이다.

• 대한인간공학회지
• /
• 제33권6호
• /
• pp.477-486
• /
• 2014

Objective:This study aims to devise industrial injury prevention measures by analyzing industrial injury characteristics including the status of industrial injuries, source of industrial injury and accident type in order to prevent aging workers' industrial injuries that account for more than half in the workplaces in agriculture. Background: Continuous migration from farm to city takes place among young people in rural areas in Korea, a traditionally agricultural country due to rapid industrialization and economic development. The aging rate in rural areas in 2013 was 37.3%, about three times higher than the total aging rate of 12.2% in Korea. According to industrial injury statistics of the Ministry of Employment and Labor, the number of industrial injuries in agriculture shows an uptrend and the industrial injuries of aging workers account for more than 50% each year. Method: Of the 2,970 industrial injury cases occurred in the workplaces in agriculture for five years during 2008 and 2012 offered by a national agency related to health and safety, this study analyzed 1,767 industrial injury cases of aging workers. Results: As a result of an analysis on aging workers' industrial injuries by company size in agriculture, 89.8% of the total number of industrial injuries were analyzed to occur in small scale company. According to aging workers' industrial injuries by source of industrial injury and accident type, the outdoor floor and a fall were analyzed to be the highest at 16.5% and 26.1%, respectively. Conclusion: This study analyzed aging workers' industrial injuries by company size, age, job duration, accident severity, gender, nationality, the source of industrial injury and accident type in order to identify industrial injury characteristics in agriculture. Application: The identification of industrial injury characteristics of aging workers in agriculture is judged to be helpful to devising effective measures to prevent industrial injuries.

• 한국지역사회생활과학회지
• /
• 제28권4호
• /
• pp.653-667
• /
• 2017

The purpose of this study were to investigate the socio-economic impacts of urban-to-rural migration on the rural community and to identify the factors influencing rural residents' recognition of the socio-economic impacts of urban-to-rural migration on the rural community. For the purpose, this study analyzed Korea Rural Economic Institute's rural residents survey(2016), using multiple regression model. The main finding of this study were as follows: Positive social impacts of urban-to-rural migration on rural community were (1) contributing to community sustainability through population growth, (2) contributing to securing agricultural human resources, and others. Negative social impacts of urban-to-rural migration on rural community were (1) increasing unnecessary complaints and deepening distrust, (2) weakening of community consciousness, and others. Positive economic impacts of urban-to-rural migration on rural community were (1) increasing the value of residents' property, (2) contributing to local finance through increased local tax revenue, and others. Negative economic impacts of urban-to-rural migration on rural community were (1) difficulty of scaling farmland due to small-scale farming, (2) land shortage caused by rising land prices, and (3) fierce competition to secure labor force. According to the multiple regression analysis, the major factors influencing rural residents' recognition of the socio-economic impacts of urban-to-rural migration were (1) villagers' general attitude toward urban-to-rural migrants, (2) urban-to-rural migrants' community participation, (3) age, and (4) fitness of village in urban-to-rural migration.

• 한국작물학회:학술대회논문집
• /
• 한국작물학회 1998년도 21세기 한반도 농업전망과 대책(한국작물학회.한국육종학회 공동주관 심포지움 회보)
• /
• pp.68-111
• /
• 1998

The structure of the Hanwoo (Korean Native Cattle) Industry remains very weak and vulnerable to the WTO/IMF system. Considering that the majority of cattle farmers are small sized, and that marketing systems are outdated and inefficient, rapid expansion of lower priced beef imports by WTO system and rapid increasing of production costs by IMF system would lead to the deprivation of a regular source of farm income and threaten the stability of rural life. Accordingly, the Hanwoo industry should be expanded in accordance with progress in the implementation of (1) programs for the structural adjustment and (2) measures to compensate for the loss. Efforts for lowering major production factor costs needs to continue, In order to increase the supply of calves at low cost, the programs of collective cow-calf farms should be expanded, thereby reducing the cost of calf purchase, which constitutes the largest share of Hanwoo production cost. Also, feedlot operations should be encouraged for small herd farms in order to achieve a substantial saving in beef production costs by integrated operations from calf production to cattle fattening. A substantial saving would also be made by collective purchase and distribution of various inputs through the cooperatives' channels. Extension services should be strengthened for cattle farm management, cattle care and feeding, prevention of cattle disease, etc. In order to minimize cash outlays for commercial mixed feeds, utilization of far by-products as feeds should be enhanced and production of forage crops productive of resources, such as land and rural labor, during the farm o(f-season, needs to be encouraged. Also, technological development for enhancing the nutritional value of farm by-products should be encouraged. Measures for successful segregation of the Hanwoo beef market should be implemented, thereby enhancing incentive for quality beef producers and protecting consumers willing to pay higher price for quality beef. For development of the Hanwoo industry, a considerable time frame would be required in order for (1) small livestock farmers to make a successful adjustment by staying in the enterprise and achieving increased price efficiency (2) livestock farmers to acquire know-how for producing quality Hanwoo beef, (3) the ongoing Government policy of enhancing price-quality competitiveness, and for improving the quality Hanwoo beef marketing to take root. (4) consumers to increase their ability to distinguish meat quality, and others.