• Proceedings of the Korean Magnestics Society Conference
• /
• 1995.05a
• /
• pp.88-89
• /
• 1995

• Proceedings of the Korean Magnestics Society Conference
• /
• 1995.05a
• /
• pp.106-107
• /
• 1995

• Korean Journal of Materials Research
• /
• v.20 no.10
• /
• pp.501-507
• /
• 2010

Changes in surface morphology and roughness of dc sputtered ZnO:Al/Ag back reflectors by varying the deposition temperature and their influence on the performance of flexible silicon thin film solar cells were systematically investigated. By increasing the deposition temperature from $25^{\circ}C$ to $500^{\circ}C$, the grain size of Ag thin films increased from 100 nm to 1000 nm and the grain size distribution became irregular, which resulted in an increment of surface roughness from 6.6 nm to 46.6 nm. Even after the 100 nm thick ZnO:Al film deposition, the surface morphology and roughness of the ZnO:Al/Ag double structured back reflectors were the same as those of the Ag layers, meaning that the ZnO:Al films were deposited conformally on the Ag films without unnecessary changes in the surfacefeatures. The diffused reflectance of the back reflectors improved significantly with the increasing grain size and surface roughness of the Ag films, and in particular, an enhanced diffused reflectance in the long wavelength over 800 nm was observed in the Ag back reflectors deposited at $500^{\circ}C$, which had an irregular grain size distribution of 200-1000 nm and large surface roughness. The improved light scattering properties on the rough ZnO:Al/Ag back reflector surfaces led to an increase of light trapping in the solar cells, and this resulted in a noticeable improvement in the $J_{sc}$ values from 9.94 mA/$cm^2$ for the flat Ag back reflector at $25^{\circ}C$ to 13.36 mA/$cm^2$ for the rough one at $500^{\circ}C$. A conversion efficiency of 7.60% ($V_{oc}$ = 0.93, $J_{sc}$ = 13.36 mA/$cm^2$, FF = 61%) was achieved in the flexible silicon thin film solar cells at this moment.

• Journal of the Korean Magnetics Society
• /
• v.8 no.6
• /
• pp.357-361
• /
• 1998

For CoZr/Ag/CoCr trilayered films deposited by DC and FR magnetron sputtering method, ferromagentic resonance experiments have been used to investigate the dependence of the exchange coupling between CoZr and CoCr layers separated by Ag layer on the thickness of the Ag layer. The coupling strength K increases with increasing Ag thickness up to 10 $\AA$ with a maximum value of 748 Oe, but oscillates with increasing Ag thickness in the range from 20 to 100 $\AA$. The coupling strength is positive for all samples. Hence, it seems that the exchange coupling between CoZr and CoCr layers separated by Ag layer is ferromagnetic.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.27-28
• /
• 2009

In this study, we have fabricated the 3 wt% $Li_2CO3$ doped $(Ba,Sr)TiO_3$ thick films on the Ag/Pd printed $Al_2O_3$ substrates for the LTCCs (Low Temperature Co-fired Ceramics) applications. From the X-ray diffraion analysis, 3 wt% $Li_2CO3$ doped BST thick films on the Ag/Pd printed $Al_2O_3$ substrates, which sintered at 900 $^{\circ}C$ have perovskite structure without any pyro phase. The dielectric properties of 3 wt% $Li_2CO3$ doped BST thick films were measured from 1 kHz to 1 MHz. To investigate the electrical properties of 3 wt% $Li_2CO3$ doped BST thick films, we employed the impedance spectroscopy. The complex impedance of 3 wt% $Li_2CO3$ doped BST thick films were measured from 20 Hz to 1 MHz at the various temperatures.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.1
• /
• pp.41-44
• /
• 2014

We employed UV-Ozone treatment method for the fabrication of dense and highly conductive nanoparticle thin films. We demonstrated the UV-Ozone treatment effect on the silver nanoparticle thin films as a function of time and temperature. The capping layers of nanoparticles were decomposed after UV-Ozone treatment and dense nanoparticle thin films were obtained. Moreover, electrical and mechanical properties of the thin films after UV-Ozone treatment were measured by using resistance measurements under tension in an in-situ tensile tester. The initial resistance of nanoparticle thin films was decreased by 82.6% with optimized UV-Ozone treatment condition of $150^{\circ}C$ for 20 minutes.

• Journal of the Korean Ceramic Society
• /
• v.43 no.11 s.294
• /
• pp.738-742
• /
• 2006

We report on the effects of co-doping with fluorine on properties of ZnO thin films grown by pulsed-laser deposition. The transport characteristics of Ag-F and Li-F codoped ZnO films were determined by Hall-effect measurements at room temperature. Ag-F codoped ZnO films showed n-type semiconducting behaviors. An ambiguous carrier type was observed in Li-F codoped ZnO films grown at a temperature of 500$^{\circ}C$ with the oxygen pressures of 20 and 200 mTorr. The qualities of the codoped ZnO films were studied by X-ray diffraction, atomic force microscopy, X-ray photoemission spectroscopy, and photoluminescence.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.873-876
• /
• 2000

Characteristics of piezoelectric thick films prepared by screen printing method were investigated. The piezoelectric thick films were printed using Pb(Mg,Nb)O$_3$-Pb(Zr,Ti)O$_3$system. The lower electrodes were coated with various thickness of Ag-Pd by screen printing to investigate the effect as a diffusion barrier and deposited with Pt by sputtering on Ag-Pd. The ceramic paste was prepared by mixing powder and binder with various ratios using three roll miller. The fabricated thick films were burned out at 650$^{\circ}C$ and sintered at 950$^{\circ}C$ in the O$_2$condition for each 20, 60min after printing with 350mesh screen. The thickness of piezoelectric thick film was 15∼20 $\mu\textrm{m}$ and the Ag-Pd electrode acted as a diffusion barrier above 3 $\mu\textrm{m}$ thickness. When the lower electrode Ag-Pd was 6 $\mu\textrm{m}$ and the piezoelectric thick films were sintered by 2nd step (650$^{\circ}C$/20min and 950$^{\circ}C$/1h) using paste mixed Pb(Mg,Nb)O$_3$-Pb(Zr,Ti)O$_3$$.$ MnO$_2$+ Bi$_2$O$_3$. V$_2$O$\_$5/ and binder in the ratio of 70:30, the remnant polarization of thick film was 9.1 ${\mu}$C /cm$^2$.

• ETRI Journal
• /
• v.19 no.2
• /
• pp.71-81
• /
• 1997

We report on the room-temperature-growth of highly uniform and ultrathin Ag films on Sb-terminated Si(111) surfaces, as evidenced from a scanning tunneling microscopy (STM) study in an UHV system. With predeposition of one monolayer (ML) of Sb, uniform growth of Ag islands was observed at room temperature. The Sb layer suppresses the surface diffusion of Ag atoms on Si surface and increases the Ag island density, and then the increased island density is believed to cause coalescence of Ag islands before the beginning of multilayer growth in higher coverages, resulting in the growth of atomically flat and uniform islands on the Sb surfactant layer.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.2
• /
• pp.107-112
• /
• 2002

We have studied diffusion behavior of NiFe/Ag bilayer deposited by on silicon Ion Beam Sputtering methods. The diffusion behavior of NiFe and Ag in NiFe/Ag thin film is analyzed by Medium Energy Ion Scattering Spectroscopy. For samples without Ta underlayer, silicides such as Ni-Si or Fe-Si were formed at Si substrate and NiFe interface. In contrast, Ag predominantly diffused into the NiFe layer probably through their grain boundaries for Ta underlayered samples.