• 대한전자공학회논문지
• /
• 제20권1호
• /
• pp.22-26
• /
• 1983

열확산(thermal diffusion)법을 이용하여 면적이 3.36㎠인 P+N 전지와 P+NN+ 전지를 제작하였다. 100mW/㎠의 인공 조명에서 측정한 결과 940℃에서 15분 보론확산(boron Predeposition)을 하고, 800℃에서 20분 열처리(annealing)하여 제작한 P+N전지는 전면적(수광면적) 변환 효율이 13.4%(14.7%)이었다. 뒷면을 1050℃에서 인(Phosphorus)을 확산한 후, 앞면을 940℃에서 15분 보론 확산하고, 800℃에서 50분 열처리하여 만든 P+NN+전지의 전면적(수광면적) 변환 효율은 14.3%(15.6%)이었다. 뒷면의 인 확산으로 게더링(gettering) 작용과 BSF 효과에 의해서 P+NN+ 전지가 P+N전지보다 캐리어 수명이 약 2∼3배 증가되었다. 그리고 효율 개선을 위해 AR로팅, Ag전기도금, 미세한 그리드 패턴, 앞면 불순물 주입량 조절 등을 행하였다.

• 한국재료학회지
• /
• 제17권9호
• /
• pp.453-457
• /
• 2007

Interest in use of ink-jet printing for pattern-on-demand fabrication of metal interconnects without complicated and wasteful etching process has been on rapid increase. However, ink-jet printing is a wet process and needs an additional thermal treatment such as an annealing process. Since a metal ink is a suspension containing metal nanoparticles and organic capping molecules to prevent aggregation of them, the microstructure of an ink-jet printed metal interconnect 'as dried' can be characterized as a stack of loosely packed nanoparticles. Therefore, during being treated thermally, an inkjet-printed interconnect is likely to evolve a characteristic microstructure, different from that of the conventionally vacuum-deposited metal films. Microstructure characteristics can significantly affect the corresponding electrical and mechanical properties. The characteristics of change in microstructure and electrical resistivity of inkjet-printed silver (Ag) films when annealed isothermally at a temperature between 170 and $240^{\circ}C$ were analyzed. The change in electrical resistivity was described using the first-order exponential decay kinetics. The corresponding activation energy of 0.44 eV was explained in terms of a thermally-activated mechanism, i.e., migration of point defects such as vacancy-oxygen pairs, rather than microstructure evolution such as grain growth or change in porosity.

• 한국표면공학회지
• /
• 제49권1호
• /
• pp.54-61
• /
• 2016

Screen printing of commercially available Ag paste is the most widely used method for the front side metallization of Si solar cells. However, the metallization using Ag paste is expensive and needs high temperature annealing for reliable contact. Among many metallization schemes, Ni/Cu/Sn plating is one of the most promising methods due to low contact resistance and mass production, resulting in high efficiency and low production cost. Ni layer serves as a barrier which would prevent copper atoms from diffusion into the silicon substrate. However, Ni based schemes by electroless deposition usually have low thermal stability, and require high annealing process due to phosphorus content in the Ni based films. These problems can be resolved by adding W element in Ni-based film. In this study, Ni-W-P alloys were formed by electroless plating and properties of it such as sheet resistance, resistivity, specific contact resistivity, crystallinity, and morphology were investigated before and after annealing process by means of transmission line method (TLM), 4-point probe, X-ray diffraction (XRD), and Scanning Electron Microscopy (SEM).

• 한국재료학회지
• /
• 제32권5호
• /
• pp.243-248
• /
• 2022

This study demonstrates a different approach method to fabricate antimony selenide (Sb₂Se₃) thin-films for the solar cell applications. As-deposited Sb₂Se₃ thin-films are fabricated via electrodeposition route and, subsequently, annealed in the temperature range of 230 ~ 310℃. Cyclic voltammetry is performed to investigate the electrochemical behavior of the Sb and Se ions. The deposition potential of the Sb₂Se₃ thin films is determined to be -0.6 V vs. Ag/AgCl (in 1 M KCl), where the stoichiometric composition of Sb₂Se₃ appeared. It is found that the crystal orientations of Sb₂Se₃ thin-films are largely dependent on the annealing temperature. At an annealing temperature of 250 ℃, the Sb₂Se₃ thin-film grew most along the c-axis [(211) and/or (221)] direction, which resulted in the smooth movement of carriers, thereby increasing the carrier collection probability. Therefore, the solar cell using Sb₂Se₃ thin-film annealed at 250 ℃ exhibited significant enhancement in J_SC of 10.03 mA/cm² and a highest conversion efficiency of 0.821 % because of the preferred orientation of the Sb₂Se₃ thin film.

• 한국전기전자재료학회논문지
• /
• 제37권2호
• /
• pp.223-229
• /
• 2024

Laser-induced plasmonic sintering of metal nanoparticles (NPs) holds significant promise as a technology for producing flexible conducting electrodes. This method offers immediate, straightforward, and scalable manufacturing approaches, eliminating the need for expensive facilities and intricate processes. Nevertheless, the metal NPs come at a high cost due to the intricate synthesis procedures required to ensure long-term reliability in terms of chemical stability and the prevention of NP aggregation. Herein, we induced the self-generation of metal nanoparticles from Ag organometallic ink, and fabricated highly conductive electrodes on flexible substrates through laser-assisted plasmonic annealing. To demonstrate the practicality of the fabricated flexible electrode, it was configured in a mesh pattern, realizing multi-touchable flexible touch screen panel.

• Advances in nano research
• /
• 제5권3호
• /
• pp.193-201
• /
• 2017

ZnO, ZnO: Cu, Ga, and ZnO: Cu, Ga, Ag thin films were obtained by oxidization of ZnS and ZnS: Cu, Ga films deposited onto glass substrates by electron-beam evaporation from ZnS and ZnS: Cu, Ga targets and from ZnS: Cu, Ga film additionally doped with Ag by the closed space sublimation technique at atmospheric pressure. The film thickness was about $1{\mu}m$. The oxidation was carried out at $600-650^{\circ}C$ in air or in an atmosphere containing water vapor. Structural characteristics were investigated by X-ray diffraction (XRD) and atomic force microscopy (AFM). Photoluminescence (PL) spectra of the films were measured at 30-300 K using the excitation wavelengths of 337, 405 and 457.9 nm. As-deposited ZnS and ZnS: Cu, Ga films had cubic structure. The oxidation of the doped films in air or in water vapors led to complete ZnO phase transition. XRD and AFM studies showed that the grain sizes of oxidized films at wet annealing were larger than of the films after dry annealing. As-deposited doped and undoped ZnS thin films did not emit PL. Shape and intensity of the PL emission depended on doping and oxidation conditions. Emission intensity of the films annealed in water vapors was higher than of the films annealed in the air. PL of ZnO: Cu, Ga films excited by 337 nm wavelength exhibits UV (380 nm) and green emission (500 nm). PL spectra at 300 and 30 K excited by 457.9 and 405 nm wavelengths consisted of two bands - the green band at 500 nm and the red band at 650 nm. Location and intensities ratio depended on the preparation conditions.

• Nuclear Engineering and Technology
• /
• 제47권5호
• /
• pp.608-616
• /
• 2015

The migration of silver (Ag) in silicon carbide (SiC) and $^{110m}Ag$ through SiC of irradiated tristructural isotropic (TRISO) fuel has been studied for the past three to four decades. However, there is no satisfactory explanation for the transport mechanism of Ag in SiC. In this work, the diffusion coefficients of Ag measured and/or estimated in previous studies were reviewed, and then pre-exponential factors and activation energies from the previous experiments were evaluated using Arrhenius equation. The activation energy is $247.4kJ{\cdot}mol^{-1}$ from Ag paste experiments between two SiC layers produced using fluidized-bed chemical vapor deposition (FBCVD), $125.3kJ{\cdot}mol^{-1}$ from integral release experiments (annealing of irradiated TRISO fuel), $121.8kJ{\cdot}mol^{-1}$ from fractional Ag release during irradiation of TRISO fuel in high flux reactor (HFR), and $274.8kJ{\cdot}mol^{-1}$ from Ag ion implantation experiments, respectively. The activation energy from ion implantation experiments is greater than that from Ag paste, fractional release and integral release, and the activation energy from Ag paste experiments is approximately two times greater than that from integral release experiments and fractional Ag release during the irradiation of TRISO fuel in HFR. The pre-exponential factors are also very different depending on the experimental methods and estimation. From a comparison of the pre-exponential factors and activation energies, it can be analogized that the diffusion mechanism of Ag using ion implantation experiment is different from other experiments, such as a Ag paste experiment, integral release experiments, and heating experiments after irradiating TRISO fuel in HFR. However, the results of this work do not support the long held assumption that Ag release from FBCVD-SiC, used for the coating layer in TRISO fuel, is dominated by grain boundary diffusion. In order to understand in detail the transport mechanism of Ag through the coating layer, FBCVD-SiC in TRISO fuel, a microstructural change caused by neutron irradiation during operation has to be fully considered.

• Advances in nano research
• /
• 제3권3호
• /
• pp.133-141
• /
• 2015

Influence of Ag nanoparticles on optical and photovoltaic properties of, silicon substrates, silicon solar cells and glass have been investigated. Silver nanoparticles have been fabricated by evaporation of thin Ag layers followed by the thermal annealing. The surface plasmon resonance peak was observed in the absorbance spectrum at 470 nm of glass with deposited silver nanoparticles. It is demonstrated that deposition of silver nanoparticles on silicon substrates was accompanied with a significant decrease in reflectance at the wavelength 360-1100 nm and increase of the absorption at wavelengths close to the band gap for Si substrates. We studied influence of Ag nanoparticles on photovoltaic characteristics of silicon solar cells without and with common use antireflection coating (ARC). It is shown that silver nanoparticles deposited onto the front surface of the solar cells without ARC led to increase in the photocurrent density by 39% comparing to cells without Ag nanoparticles. Contrary to this, solar cells with Ag nanoparticles deposited on front surface with ARC discovered decrease in photocurrent density. The improved performance of investigated cells was attributed to Ag-plasmonic excitations that reduce the reflectance from the silicon surface and ultimately leads to the enhanced light absorption in the cell. This study showed possibility of application of Ag nanoparticles for the improvement of the conversion efficiency of waferbased silicon solar cells instead of usual ARC.

• 한국표면공학회지
• /
• 제54권3호
• /
• pp.119-123
• /
• 2021

SnO₂ single layer and SnO₂/Ag/SnO₂ (SAS) tri-layered films were deposited on the glass substrate by RF and DC magnetron sputtering at room temperature and then the effect of Ag interlayer on the opto-electrical performance of the films were considered. As deposited SnO₂ films show a visible transmittance of 85.5 % and a sheet resistance of 1.2×10⁴ Ω/□, the SAS films with a 15 nm thick Ag interlayer show a lower resistance of 18.8 Ω/□ and a visible transmittance of 70.6 %, respectively. The figure of merit based on the optical transmittance and sheet resistance revealed that the Ag interlayer in the SnO₂ films enhances the opto-electrical performance without substrate heating or annealing process.

• 한국진공학회지
• /
• 제16권4호
• /
• pp.291-297
• /
• 2007

본 연구에서는 Ag-Cu합금 코팅에 의한 탄소나노튜브의 전계방출특성 변화를 연구하였다. 화학기상증착 방법을 사용하여 수직 성장시킨 탄소나노튜브에 직류 마그네트론 스퍼터를 이용하여 Ag-Cu합금을 증착하였고, 열처리 전 후의 탄소나노튜브의 표면형상 변화와 전계방출특성에 변화를 연구하였다. 연구결과 Ag-Cu합금 코팅으로 전계방출 문턱전압이 현저히 낮아졌으며 전류밀도는 $6V/{\mu}m$의 인가전압 하에서 약 5배 향상된 것을 확인하였다. 또한 Ag-Cu합금이 코팅된 탄소나노튜브는 산소가 많이 포함된 분위기에서도 안정적인 전계방출 특성을 보였으며, 이는 Ag-Cu합금 코팅이 분위기 진공에 상존하는 산소기체가 탄소나노튜브를 공격하는 것을 막아주는 역할을 하여 열악한 분위기에서도 전계방출이 안정적으로 발생하였기 때문인 것으로 생각된다.