• Journal of the Korean institute of surface engineering
• /
• v.39 no.1
• /
• pp.1-8
• /
• 2006

In this study, effect of sputtering after plasma nitriding and before PVD coating on the microstucture, microhardness, surface roughness and the adhesion strength of CrN thin films were investigated. Experimental results showed that this sputtering process not only removed surface compound layer which formed during a plasma nitriding process but also induced an alteration of the surface of plasma nitrided substrate in terms of microhardness distribution and surface roughness, which in turn affected the adhesion strength of PVD coatings. After sputtering, microhardness distribution showed general decrease and the surface roughness became increased slightly. The critical shear stress measured from the scratch test on the CrN coatings showed an approximately twice increase in the binding strength through the sputtering prior to the coating and this could be attributed to a complete removal of compound layer from the plasma nitrided surface and to an increase in the surface roughness after sputtering.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.11 no.1
• /
• pp.47-52
• /
• 2005

The wasted plastic PC/ABS retainer, polyurethane foam (PUF) and vinyl (PVC) skin. In order to investigate the recycling process, the multi-layered instrument panel Each of materials separated was shredded and crushed to create many small particles respectively. The separation of the foam and skin and retainer of zigzagged air blower. Pilot tests performed at the equipment yielded 98.8% by weight of the available PVC and 99.3% by weight of the available PC/ABS respectively. Secondly, the thermal stabilizer and the compatabilizer have been used to improve the physical propertied of recycled materials.. The properties of recycled PVC materials resulted in about 50% compared to that of virgin materials after treatment by Pb-St thermal stabilizer. In addition, the properties of recycled PC/ABS materials was also obtained about 80% compared to that of virgn materials after treatment by PMMA compatabilizer.

• Journal of Magnetics
• /
• v.12 no.1
• /
• pp.49-52
• /
• 2007

We investigated annealing effect of microforged powders on magnetic properties and electromagnetic absorption behaviors for ferromagnetic Fe-Cr metal alloy powder-polymer composites. The coercive properties greatly decreased with annealing temperature and the magnetic permeability had significantly increased after microforging and subsequent annealing treatment, due to a reduction in lattice strain of the microforged powders. The power loss in the far field regime also had greatly increased after microforging and subsequent annealing treatment in frequency range from 50 MHz to 6 GHz. As a result, the electromagnetic absorption of ferromagnetic Fe-Cr alloy metal powder-polymer composites was highly improved because of the relaxation of the internal strain during annealing process.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.4
• /
• pp.1571-1574
• /
• 2015

Background: Treatment of Helicobacter pylori (H. pylori) decreases the prevalence of gastric cancer, and may inhibit gastric precancerous lesions progression into gastric cancer. The aim of this study was to determine the effect of treatment on subsequent gastric precancerous lesion development. Materials and Methods: We prospectively studied 27 patients who had low grade dysplasia at the time of enrollment, in addition to dysplasia atrophic gastritis and intestinal metaplasia observed in all patients. All were prescribed quadruple therapy to treat H. Pylori infection for 10 days. Patients underwent endoscopy with biopsy at enrollment and then at follow up two years later. Biopsy samples included five biopsies from the antrum of lesser curvature, antrum of greater curvature, angularis, body of stomach and fundus. Results of these biopsies were compared before and after treatment. Results: Overall, the successful eradication rate after two years was 15/27 (55.6%). After antibiotic therapy, the number of patients with low grade dysplasia decreased significantly (p=0.03), also with reduction of the atrophic lesions (p=0.01), but not metaplasia. Conclusions: Treatment of H. pylori likely is an effective therapy in preventing the development of subsequent gastric premalignant lesions.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.4
• /
• pp.734-740
• /
• 2016

The micron-sized indium zinc tin oxide (IZTO) particles were prepared by spray pyrolysis from aqueous precursor solution for indium, zinc, and tin and organic additives such as citric acid (CA) and ethylene glycol (EG) were added to aqueous precursor solution for indium, zinc, and tin. The obtained IZTO particles prepared by spray pyrolysis from the aqueous solution without organic additives had spherical and filled morphologies, whereas the IZTO particles obtained with organic additives had more hollow and porous morphologies. The micron-sized IZTO particles with organic additives were changed fully to nano-sized IZTO particles, whereas the micron-sized IZTO particles without organic additives were not changed fully to nano-sized IZTO particle after post-treatment at $700^{\circ}C$ for 2 hours and wet-ball milling for 24 hours. Surface resistances of micron-sized IZTO's before post-heat treatment and wet-ball milling were much higher than those of nano-sized IZTO's after post-heat treatment and wet-ball milling. From IZTO with composition of 80 wt. % $In_2O_3$, 10 wt. % ZnO, and 10 wt. % $SnO_2$ which showed a smallest surface resistance IZTO after post-heat treatment and wet-ball milling, thin films were deposited on glass substrates by pulsed DC magnetron sputtering, and the electrical and optical properties were investigated.

• Journal of the Korean Ceramic Society
• /
• v.54 no.2
• /
• pp.114-120
• /
• 2017

In underdeveloped countries, many people suffer from water shortage due to the absence of water supply service. Although water purifiers have provided support in such situations, it is not easy to maintain water filters without a continuous supply of consumable filters. To obtain a sustainable drinking water source, appropriate technology of water treatment is necessary. Herein, a low cost water purification system was developed using natural raw materials. A non-electric water treatment system was developed using filtration through an Onggi filter, which is a type of Korean traditional earthenware with a microporous surface. The porosity and flux of the prepared Onggi filter were 29.06% and 31.63 LMH, respectively. After purification of water with total dissolved solids of 10.4 mg/L and turbidity of 100 NTU, the total dissolved solids and turbidity of the water treated using the Onggi filter decreased by 12% and 99.8%, respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.5
• /
• pp.227-232
• /
• 2012

Magnesium alloy have good physical properties such as good castability, good vibration absorption, high strength/weight ratios. Despite the desirable properties, the poor resistance of Mg alloy impedes their use in many various applications. Therefore, magnesium alloy require surface treatment to improve hardness, corrosion and wear resistance. Plasma Electrolytic Oxidation (PEO) is one the surface treatment methods to form oxide layer on Mg alloy in alkali electrolyte. In comparison with Anodizing, there is environmental process having higher hardness and faster deposition rate. In this study, the characteristics of oxide film were examined after coating the AZ31 Mg alloy through the PEO process. We changed concentration of sodium aluminate into $K_2ZrF_6$, KF base electrolyte. The morphologies of the coating layer were characterized by using scanning electron microscopy (SEM). Corrosion resistance also investigated by potentiodynamic polarization analysis. As a result, propertiy of oxide layer were changed by concentration of sodium aluminate. Increasing with concentration of sodium aluminate in electrolyte, the oxidation layer was denser and the pore size was smaller on the surface.

• Journal of Adhesion and Interface
• /
• v.14 no.3
• /
• pp.111-116
• /
• 2013

In this study, we studied surface and adhesion properties with plasma treatment for substitution of buffing and solvent-cleaning in footwear adhesion process. The distance between nozzle and rubber parts was decreased with decreasing the contact angle. And when a speed of plasma treatment increased, the contact angle increased. The result of surface roughness, Ra and Rz increased in 20% and 16% after the plasma treatment. The distance of between nozzle and rubber parts was decreased with decreasing the peel strength. And the speed of plasma treatment was increased with decreasing the peel strength.

• Nutrition Research and Practice
• /
• v.7 no.1
• /
• pp.3-8
• /
• 2013

Buckwheat is known as a health food but is one of the major food allergens triggering potentially fatal anaphylaxis in Asia, especially in Japan and Korea. This study was conducted to investigate the characteristic of enzymatic resistance of buckwheat protein and allergenic potential. Enzymatic resistance of buckwheat protein was performed with in vitro digestibility test in simulated gastric fluid (SGF), pH 1.2, using pepsin and simulated intestinal fluid (SIF) using chymotrypsin. Reactivity of buckwheat proteins to human IgE was performed using six allergic patients sensitized to buckwheat. Buckwheat's IgE levels were measured using the Phadia UniCAP-system. Buckwheat protein, 16 kDa, still remained after 30 min treatment of pepsin on SDS-PAGE. Even though 16 kDa almost disappeared after 60 min treatment, two out of the six buckwheat patients' sera showed reactivity to hydrolysate after 60 min treatment, indicating that allergenicity still remained. In simulated intestinal fluid (SIF) using chymotrypsin, buckwheat protein, 24 kDa, showed resistance to hydrolysis with chymotrypsin on SDS-PAGE, and still had allergenicity based on the result of ELISA. Our results suggest that buckwheat proteins have strong resistance to enzyme degradation. This may be attributed in part to the allergenic potential of buckwheat. Further study should be continued regarding buckwheat allergy.

• Fibers and Polymers
• /
• v.4 no.2
• /
• pp.84-88
• /
• 2003

The properties of a woven fabric made of poly(trimethylene terephthalate) (PTT) were investigated. The PTT fab-ric of draw textured yarn (DTY) showed excellent stretch as good as a fabric containing spandex. However, the unique stretch of the PTT fabric reduced dramatically by simple heat-treatment even at as low as $80^{\circ}C$. To understand the phenomenon, the crimp rigidity of the DTY was observed by SEM. It was found that the drastic reduction of stretch was caused by irreversible uncrimping of PTT DTY after heat-treatment. Conclusively, it is of importance to optimize the texturing conditions for PTT DTY to make the crimp more stable.