• 대한안전경영과학회지
• /
• 제25권1호
• /
• pp.61-66
• /
• 2023

The purpose of this study is to compare and analyze the flame retardant performance of Japanese cypress(Chamaecyparis obtusa) plywood, commonly used in indoor decoration, furniture, and tableware, by treating it with three different fire retardants with different primary ingredients. The experiment was conducted in compliance with Article 31, Paragraph 2 of the Enforcement Decree of the Fire Facilities Installation and Management Act and Articles 4 and 7-2 of the Flame Retardant Performance Standards. After flame time, after glow time, char length, and char area were measured. As a result, first, after flame time was measured at 0 seconds regardless of whether the flame retardant treatment was applied. Second, after glow time was relatively long, measuring 22.7 seconds without treatment, which is likely due to the weak fire resistance and high concentration of carbon monoxide generated by the chemical characteristics of the Japanese cypress itself. Third, it was confirmed that the effects of the primary ingredient, phosphorus, in the flame retardant treatment varied depending on the technological development of the manufacturers of the same species of Japanese cypress plywood. In the future, it is expected that the results of this study will provide fundamental data to select flame retardant treatments that show high flame retardant performance according to the botanical characteristics of the wood.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.911-914
• /
• 1992

We have investigated the micro-discharge in plasma display panel using 2 dimensional 2 fluid MHD equations. Plasma display utilizes the physical phenomena of the normal glow or abnormal glow and is considered to be able to provide the largest display area among various flat panel. 2 fluid, 2 dimensional Magneto-Hydro-Dynamic equations are applied to Computational field of 100${\times}$800${\mu}m^2$. Time varing glows and after-glows were investigated for 11 $\mu$sec. We obtained the distribution of the microscopic variables such as the density, temperature, velocity of Ne+Ar0.1% gas plasma. During the first 6$\mu$ sec, glow discharge dued to DC pulse was investigated. Time varing phenomena of after-glow was also investigated during the last 5 $\mu$set. From results, it was found that the driving efficiency of a DC Plasma Display Panel could be improved when the diffusion of ions and electrons are controlled by the pulses applied to the auxiliary anode.

• Korean Chemical Engineering Research
• /
• 제49권6호
• /
• pp.704-709
• /
• 2011

접촉글로우방전 전기분해(CGDE)에 의한 후코이단의 저분자화에 대해 연구하였다. CGDE 공정 후에 후코이단을 기능성 식품재료로 사용하기 위해 유기산을 전해질로 사용하였다. 실험결과 유기산을 이용한 전기분해에 의해 후코이단의 분자량을 효과적으로 감소시킴을 보였다. 전해질의 농도가 증가하면 글로우방전 시작 전압이 감소하고 글로우방전시작 전류는 증가하였다. 반응시간에 따른 후코이단의 분자량 변화로부터 저분자화반응은 1차 반응속도 식을 따름을 보였다. 유기산을 이용한 CGDE에 의해 후코이단의 분자량이 처음의 약 1/77로 감소하였으며, CGDE 저분자화 과정에서 유리된 황산기 함량이 작았다.

• Korean Chemical Engineering Research
• /
• 제46권5호
• /
• pp.886-891
• /
• 2008

접촉 글로우방전 전기분해(CGDE)는 일반적인 전기분해와 다르게 높은 전압에서 전극과 전극을 둘러싼 전해질 사이에 글로우 방전에 의한 플라즈마가 형성돼 일어나는 전기분해다. 본 연구에서는 먼저 NaCl 용액에서 CGDE 거동을 파악하고 그리고 CGDE에 의한 후코이단의 저분자화에 대해 연구하였다. NaCl 전해질에서 CGDE 과정이 시작되면 전압 증가에 따라 글로우 방전이 활발하게 되고 그에 따라 전류밀도가 감소하고 온도가 내려갔다. 반응시간에 따른 후 코이단의 분자량 변화로부터 저분자화반응은 1차 반응속도 식을 따름을 보였다. CGDE에 의해 후코이단의 분자량이 처음의 약 1/40로 감소하였으며, CGDE 저분자화 과정에서 황산기 함량과 fucos 함량의 감소가 없었다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제17권8호
• /
• pp.2140-2156
• /
• 2023

The Wireless Sensor Network (WSN), is constructed out of teeny-tiny sensor nodes that are very low-cost, have a low impact on the environment in terms of the amount of power they consume, and are able to successfully transmit data to the base station. The primary challenges that are presented by WSN are those that are posed by the distance between nodes, the amount of energy that is consumed, and the delay in time. The sensor node's source of power supply is a battery, and this particular battery is not capable of being recharged. In this scenario, the amount of energy that is consumed rises in direct proportion to the distance that separates the nodes. Here, we present a Hybrid Firefly Glow-Worm Swarm Optimization (HF-GSO) guided routing strategy for preserving WSNs' low power footprint. An efficient fitness function based on firefly optimization is used to select the Cluster Head (CH) in this procedure. It aids in minimising power consumption and the occurrence of dead sensor nodes. After a cluster head (CH) has been chosen, the Glow-Worm Swarm Optimization (GSO) algorithm is used to figure out the best path for sending data to the sink node. Power consumption, throughput, packet delivery ratio, and network lifetime are just some of the metrics measured and compared between the proposed method and methods that are conceptually similar to those already in use. Simulation results showed that the proposed method significantly reduced energy consumption compared to the state-of-the-art methods, while simultaneously increasing the number of functioning sensor nodes by 2.4%. Proposed method produces superior outcomes compared to alternative optimization-based methods.

• Bulletin of the Korean Chemical Society
• /
• 제13권6호
• /
• pp.620-624
• /
• 1992

The analytical performance of glow discharge mass spectrometer (GD-MS), using a flat type ion source is discussed. The efficiency of ion extraction was maximized at the distance between anode and cathode of 6 mm. At the operation condition of 4 mA, -1000 volt, and 1 mbar for the source, the optimum voltages for sampler and skimmer were40 volt and -280 volt, respectively. The intensities of Cu, Zn, and Mn were increased as a function of square root of current approximately. Korea standard reference materials (KSRM) were tested for an application study. The detection limits of most elements were obtained in the range of several ppm at the optimized operating condition. The peaks of aluminum and chromium were interfered by those of residual gases. The depth profile of nickel coated copper specimens (3, 5, 10 ${\mu}m$ thickness) were obtained by plotting time versus intensities of Ni and Cr after checking the thickness of nickel coated using a scanning electron microscope (SEM). At this moment, the sputtering rate of 0.2 ${\mu}m/min$ at the optimum operating condition was determined from the slope of the plot of time to the coating thickness. The roughness spectra of specimen's crater after 16 min, discharge were obtained using a Talysuf5m-120 roughness tester as well.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1751-1754
• /
• 2004

Effects of delay on the discharge time lag and the controllability of weak discharge mode were studied under single cell driving circumstances of ac PDP. It was found that sufficient number of priming particle is necessary for inducing weak discharge in ramp voltage driving. Discharge time lag was reduced dramatically under priming condition. It is speculated that the increasement of strong discharge is related to the reduction of the $Xe^*(^3P_1)$ particles during the after glow.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권11호
• /
• pp.566-571
• /
• 2004

Pulse modulation technique provide additional controling method for electron temperature and density in rf and microwave processing plasma. Transient characteristics of electron density and temperature have been measured in pulse modulated rf inductively coupled argon plasma using simple probe circuit. Electron temperature relaxation is clearly identified in the after glow stage. Controllability of average electron temperature and density depends on the modulation frequency and duty ratio. Numerical calculation of time-dependent electron density and temperature have been performed based on the global model. It has been shown that simple langmuir probe measurement method used for continuous plasma is also applicable to time-dependent measurement of pulse modulated plasma.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 영호남 학술대회 논문집
• /
• pp.72-75
• /
• 2003

Effects of delay and panel temperature on the discharge time lag and the controllability of weak discharge mode were studied under single cell driving circumstances of ac PDP. It was found that sufficient number of priming particle is necessary for inducing weak discharge in ramp voltage driving. Discharge time lag was reduced dramatically under elevated panel temperature condition It is speculated that decrement of discharge time lag at the high temperature is related to the reduction of diffusion loss of charged particles during the after glow.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1686-1688
• /
• 2003

Effects of delay and panel temperature on the discharge time lag and the controllability of weak discharge mode were studied under single cell driving circumstances of at PDP. It was found that sufficient number of priming particle is necessary for inducing weak discharge in ramp voltage driving. Discharge time lag was reduced dramatically under elevated panel temperature condition. It is speculated that decrement of discharge time lag at the high temperature is related to the reduction of diffusion loss of charged particles during the after glow.