• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.67-75
• /
• 2008

The electrostatic charging/discharging mechanism and its effects, and the system design considerations in the space plasma environment are studied in this paper. The electrostatic discharge (ESD) effects are carefully taken into account for a design of the satellite system at the early stage of the development. Generally, the electrical design requirements are specified to protect the satellite system from the ESD effects in the electromagnetic compatibility specifications. Those requirements are included the grounding, the bonding, the shielding, the conductive coating, the electric interfacing and so on. The space charging is caused by the increasing of the voltage difference between the each locations on the satellite surface. If the space charging is continued up to threshold, it may be occurred the system failure. This phenomenon is depended on the mission of system, electrical and mechanical configuration, system operation, and orbit condition. Therefore the related requirements are properly tailored and concentrated into the safety design.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.1
• /
• pp.8-19
• /
• 2016

This paper investigates the effects of inlet turbulence conditions and near-wall treatment methods on the heat transfer prediction of gas turbine vanes within the range of engine relevant turbulence conditions. The two near-wall treatment methods, the wall-function and low-Reynolds number method, were combined with the SST and ${\omega}RSM$ turbulence model. Additionally, the RNG $k-{\varepsilon}$, SSG RSM, and $SST_+{\gamma}-Re_{\theta}$ transition model were adopted for the purpose of comparison. All computations were conducted using a commercial CFD code, CFX, considering a three-dimensional, steady, compressible flow. The conjugate heat transfer method was applied to all simulation cases with internally cooled NASA turbine vanes. The CFD results at mid-span were compared with the measured data under different inlet turbulence conditions. In the SST solutions, on the pressure side, both the wall-function and low-Reynolds number method exhibited a reasonable agreement with the measured data. On the suction side, however, both wall-function and low-Reynolds number method failed to predict the variations of heat transfer coefficient and temperature caused by boundary layer flow transition. In the ${\omega}RSM$ results, the wall-function showed reasonable predictions for both the heat transfer coefficient and temperature variations including flow transition onset on suction side, but, low-Reynolds methods did not properly capture the variation of the heat transfer coefficient. The $SST_+{\gamma}-Re_{\theta}$ transition model showed variation of the heat transfer coefficient on the transition regions, but did not capture the proper transition onset location, and was found to be much more sensitive to the inlet turbulence length scale. Overall, the Reynolds stress model and wall function configuration showed the reasonable predictions in presented cases.

• Current Industrial and Technological Trends in Aerospace
• /
• v.7 no.1
• /
• pp.68-78
• /
• 2009

In this paper, the electrostatic charging and discharging mechanism, and its effects in space plasma environment are reviewed and the system design control documents, ESD analysis tools and modelling techniques, and the SPIS program in Europe are introduced. A design of the satellite system against the electrostatic discharge (ESD) effects in space plasma environments is carefully taken into account at the early stage of development. In a view of the space system design, it really depended on the mission of system, electrical and mechanical configuration, system operation, and orbit condition. Behavior of the electrons and the ions in those environments may be occurred the sever problem to the satellite operation. So it is carefully understood for implementation of the satellite system. By this reason, the space environments and its effects have been comprehensively studied in U.S.A and Europe.

• Current Industrial and Technological Trends in Aerospace
• /
• v.7 no.2
• /
• pp.121-130
• /
• 2009

In this paper, the attitude and orbit control subsystem technology of new GEO communication and observation satellite using Sun sensors are introduced and analyzed. COMS is new GEO communication and Earth observation satellite based on EUROSTAR 3000 space bus technology. The attitude and orbit control subsystem of COMS adopts a configuration using three BASS and three LIASS Sun sensors to acquire the attitude error information in the specific reference frames. These Sun sensors are used to acquire Sun direction and to control the spacecraft to keep the relative attitude with respect to a reference Sun direction in both transfer and operational orbits. In this paper, the mathematical models of BASS and LIASS are described as well as their operational implementation in the flight software.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.10
• /
• pp.791-797
• /
• 2018

In this work, the high-altitude environment simulation study was carried out at an altitude of 65 km exceeding Mach number of 6 after the launch of Korean Space Launch Vehicle using a shock tunnel. To minimize the flow disturbance due to the strut support of test model as much as possible, a few different types of strut configurations were considered. Using the configuration with minimum disturbance, the high-altitude environment simulation experiment including a propulsion system with a single-plume, was conducted. From the thruster test through flow visualization, not only a shockwave pattern, but a general flow-field pattern from the mutual interaction between the exhaust plume and the free-stream undisturbed flow, was experimentally observed. The comparison with the computation fluid dynamic(CFD) results, showed a good agreement in the forebody whereas in the afterbody and the nozzle the disagreement was about ${\pm}7%$ due to unwanted shockwave formation emanated from the nozzle-exit.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.1
• /
• pp.29-36
• /
• 2014

Hybrid rocket displays many different low frequency pressure oscillations during combustion. Thermal lag between solid and gas phase is the primary mechanism to trigger low frequency pressure oscillations of around 10Hz, and Helmholtz or $L^*$ mode also produces other types of low frequency oscillations above 10 Hz which is associated with the change in combustion volume. Since the flow characteristics in hybrid rocket is very similar to those in solid rocket combustion, it is not surprising to observe similar pressure oscillation behaviors. Experimental test shows that combustion pressure suddenly turns into to a big amplitude oscillation around 10Hz then followed by returning to an original pressure level after a short period combustion. Further investigations show that this instability is independent of the change in O/F ratio at all. One of the possible candidates is the vortex shedding dynamics over the backward step in the post combustion chamber. It is required to investigate the low frequency oscillation mechanism in the future study.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.1
• /
• pp.9-17
• /
• 2015

The basic flow configuration is composed of a plane, double shear layer where relatively thin mid gas layer is sandwiched between air and fuel stream. The present study describes numerical investigations concerning the combustion enhancement according to a variation of mid layer thickness. In this case, the effect of heat release in turbulent mixing layers is important. For the numerical solution, a fully conservative unsteady $2^{nd}$ order time accurate sub-iteration method and $2^{nd}$ order TVD scheme are used with the finite volume method including k-${\omega}$ SST model. The results consists of three categories; single shear layer consists of fuel and air, inert gas sandwiched between fuel and air, cold fuel gas sandwiched between fuel and air. The numerical calculations has been carried out in case of 1, 2, 4 mm of mid layer thickness. The height of total gas stream is 4 cm. The combustion region is broadened in case of inert gas layer of 2, 4 mm thickness and cold fuel layer of 4 mm thickness compared with single shear layer.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.5
• /
• pp.19-30
• /
• 2016

We presented a hydrodynamic modeling necessary to accurately reproduce shock-induced detonation of pyrotechnic initiator. The methodology for such numerical prediction of shock propagation is quite straight forward if the models are properly implemented and solved in a well-formulated shock physics code. A series of SSGT(Small Scale Gap Test) and detailed hydrodynamic simulation are conducted to quantify the shock sensitivity of an acceptor that contains 97.5% RDX. A TBI(Through Bulkhead Initiator) system, consisting of a train configuration of Donor(HNS+HMX) - Bulkhead(STS) - Acceptor(RDX), were investigated to further validate the interaction between energetic and non-reactive materials for predicting the detonating response for successful operation of such small pyro device.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.65-72
• /
• 2012

Numerical simulations were performed to study the stall characteristics of turboprop aircraft. Stall characteristics were qualitatively investigated using the computational results of various configurations based on the combinations of propeller and high lift device. For the analysis of stall characteristics, three-dimensional Navier-Stokes solver with Spalart-Allmaras turbulence model was used and the relative motion between propeller and wing was simulated using sliding mesh technique. For the cruise configurations, major flow separation was occurred at the fuselage/wing fairing and the separation was reduced under propeller slipstream condition. For the high lift device configuration without propeller, major flow separation was occurred at the outboard side of nacelle. With rotating propeller, early stall onset due to low relative velocity and high effective angle of attack was observed on the outboard wing section. Regarding rotating direction of propeller, inboard-down direction was preferred due to the stall delay effect of propeller slipstream.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.238-247
• /
• 2004

Realtime Simulation and HILS are essential tools for modern aircraft control system design and development. But developing the HILS has been a big and complex task to meet the realtime simulation requirement. So these days there have been efforts to minimize these task. New advanced concept and design tools are being developed. In this paper, these new advanced concept and design tools were used to develop the realtime simulation and HILS environment for rotorcraft. The H/W 문 S/W requirement and system configuration for the developing system will be described on the paper.