• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1320-1326
• /
• 2011

The maximum speed of high-speed rail is restricted to various factors such as track condition including slope and radius, tunnel and dynamic stability of vehicle. Among the various factors, traction effort and resistance to motion is principal and basic factor. In addition, at high speed over 300km/h, aerodynamic drag amounts up to 80% of resistance to motion, that it can be said that aerodynamic drag is the most important factor to decide the maximum speed of high-speed rail system. This paper deals with a measure to increase the maximum speed of high-speed train by reducing aerodynamic drag. The traction effort curve and resistance to motion curve of existing high-speed train under development has been employed to set up the target of aerodynamic drag reduction to reach up to 500km/h without modification traction system. In addition, the contribution of various sources of aerodynamic drag to total value has been analyzed and the strategy for implementation of aerodynamic drag reduction has been discussed based on the aerodynamic simulation results around the train using computational fluid dynamics.

• 한국철도학회논문집
• /
• 제19권6호
• /
• pp.709-716
• /
• 2016

고속열차의 공기저항 저감을 위해 KTX-산천의 구성요소별 공기저항을 상세하게 분석하였다. 전체 공기저항의 약 42.9%는 동력차(선두차, 후미차)에서 그리고 약 10.1%는 대차에서 유발되는 것으로 나타났다. 전두부의 공기저항 저감을 위해 Broyden-Fletcher-Goldfarb-Shanno 기법을 이용한 전두부 최적설계를 수행하였다. 그리고 차체 공기저항 저감을 위해 동력차 형상 변화 및 대차커버를 적용하였다. 공기저항 저감을 위해 최적설계된 편성열차의 공기저항은 KTX-산천 대비 약 15.0% 저감되었으며, 주행저항은 속도 350km/h에서 약 12% 감소될 것으로 예상된다.

• Wind and Structures
• /
• 제12권4호
• /
• pp.285-298
• /
• 2009

For long-span suspension bridges with their intrinsic limit in flutter, some counter measures, for example, central stabilizers, should be adopted to improve aerodynamic stability to meet with the appropriate wind resistance requirements. The present paper introduces aerodynamic stabilization for long-span suspension bridges with box girders by using central stabilizers based on Xihoumen Bridge with the main span of 1650 m. The aerodynamic stabilization study covers experimental investigation of sectional model testing, comprehensive evaluation of three central stabilizers and theoretical analysis of stabilizing mechanism related to flutter derivatives, aerodynamic damping and degree participation.

• 한국전산유체공학회지
• /
• 제19권1호
• /
• pp.41-46
• /
• 2014

The aerodynamic drag of high-speed train has been calculated and the effect of bogie side fairing on the aerodynamic drag has been investigated. Computational Fluid Dynamics (CFD) simulation based on steady-state 3 dimensional Navier-Stokes equation has been conducted employing FLUENT 12 and the aerodynamic model of HEMU-430x, the Korean next generation high-speed train under development has been built using GAMBIT 2.4.6. Three types of bogie side fairing configuration, the proto-type without fairing, half-covered fairing to avoid the interference with the bogie frame and full-covered fairing have been adopted to the train model to compare the drag reduction effects of the bogie side fairing configurations and the numerical results yields that the bogie side fairing can reduce the aerodynamic drag of the 6-car trainset up to 7.8%. The aerodynamic drag coefficient of each vehicle as well as the flow structures around the bogie system have also been examined to analyze the reason and mechanism of the drag reduction by bogie side fairing.

• 한국자동차공학회논문집
• /
• 제14권2호
• /
• pp.194-201
• /
• 2006

Roof-fairing and deflector system have been used on heavy-duty trucks to minimize aerodynamic drag force not only for driving stability of the truck but also for energy saving by reducing the required driving power of the vehicle. In this study, a numerical simulation was carried out to see aerodynamic effect of the drag reducing device on the model vehicle. Drag and lift force generated on the five different models of the drag reducing system were calculated and compared them each other to see which type of device is efficient on the reduction of driving power of the vehicles quantitatively. An experiment has been done to see airflow characteristics on the model vehicles. Airflow patterns around the model vehicles were visualized by smoke generation method to compare the complexity of airflow around drag reducing device. From the results, the deflector systems(Model 5,6) were revealed as a better device for reduction of aerodynamic drag than the roof-fairing systems(Model 2,3,4) on the heavy-duty truck and it can be expected that over 10% of brake power of an engine can be saved on a tractor-trailer by the aerodynamic drag reducing device at normal speed range($80km/h{\sim}$).

• 한국철도학회논문집
• /
• 제16권3호
• /
• pp.169-174
• /
• 2013

고성능 EMU 열차의 형상 개선을 통한 공기저항 저감 효과를 알아보기 위하여 3차원정상 Navier-Stokes 방정식과 2방정식 난류 모델을 이용한 전산유체역학을 이용하여 수치해석을 수행하였다. 전산시뮬레이션에는 FLUENTTM ver.13과 Gambit 2.4.6이 사용되었으며, 기본 형상과 유선형으로 개선된 형상에 대하여 계산을 수행하였다. 또한, 터널 내 주행 시의 공기저항 특성을 살펴보기 위하여 개활지에서의 공기저항 계산도 수행하였으며, 차량 별 공기저항 기여도에 대한 분석도 수행되었다. 유선형으로 개선된 형상의 열차는 절편형 전두부와 돌출된 상부 및 하부구조를 가진 기본 형상 열차에 비하여 약 9.8%의 공기저항이 저감된 것을 확인하였으며, 공기저항 저감에 따른 주행저항의 저감은 시속 80km/h에서 약 4%에 이르는 것으로 나타났다.

• 한국기후변화학회지
• /
• 제7권2호
• /
• pp.177-184
• /
• 2016

Recently, the need for technology development of commercial vehicle fuel consumption has emerged. Fuel economy improvement of transport equipment and transportation efficiency, and increasing attention to the logistics cost reduction measures. Increasing attention to the logistics cost reduction measures by fuel economy improvement of transport equipment and transportation efficiency. In this study, we have installed aerodynamic reduction device (side skirt, boat tail) to 14.5 ton cargo trucks and 45 ft tractor-trailers. And the fuel consumption was compared installed before and after. Fuel economy assessment for the aerodynamic reduction value device was tested by modifying the SAE J1321 Joint TMC/SAE Fuel Consumption Test Procedure - Type II test in according domestic situation. Greenhouse gas reductions were calculated in accordance with the scenario, including fuel consumption test results. When the 14.5 ton cargo trucks has been equipped with side skirts and boat tail, it confirmed the improvement in fuel efficiency of 4.72%. One Heavy-duty truck's the annual greenhouse gas reductions value are $6.86ton\;CO_2\;eq$. And if applying the technology to more than 50% of registered 15 ton trucks, greenhouse gas reductions are calculated as $686,826ton\;CO_2\;eq./yr$.

• Wind and Structures
• /
• 제31권1호
• /
• pp.15-20
• /
• 2020

The aircraft industry supports aviation by building aircraft and manufacturing aircraft parts for their maintenance. Fuel economization is one of the biggest concerns in the aircraft industry. The reduction in specific fuel consumption of aircraft can be achieved by a variety of means, simplest and more effective is the one to impose minor modifications in the aircraft main wing or the parts which are exposed to the air flow. This method can lead to a reduction in aerodynamic resistance offered by the air and have a smoother flight. The main objective of this study is to propose geometric design modifications on an existing aircraft wing which acts as a vortex generator and it can reduce the drag and increase lift to drag ratio, leading to lower fuel consumption. The NACA 2412 aircraft wing is modified and designed. Rigorous flow analysis is carried out using computational fluid dynamics based software Ansys Fluent. Results show that saw tooth modification to the main wing shows the best aerodynamic efficiency as compared to other modifications.

• 항공우주시스템공학회지
• /
• 제16권2호
• /
• pp.25-32
• /
• 2022

캡 루프 페어링은 상용차가 주행 시 전면부에서 발생하는 유동 박리의 저항을 제어하여 상용차 항력 계수를 줄이는 장치이다. 상용차는 구조적으로 후방의 컨테이너를 적재해야 되기 때문에 차량의 주행방향으로부터 공기역학적 저항력을 피할 수 없게 설계되어 있다. 이러한 이유 때문에 유류비, 환경오염물질과 밀접한 연관을 가진다. 본 연구에서는 랭킨 반체 이론을 바탕으로 3D 페어링 형상을 설계하고 공력 해석을 통해 설계 결과를 검증하였다.

• International Journal of Automotive Technology
• /
• 제6권3호
• /
• pp.221-227
• /
• 2005

Aim of this study is to investigate an aerodynamic effect of a drag-reducing device on a heavy-duty truck. The vehicle experiences two different kinds of aerodynamic forces such as drag and uplifting force (or downward force) as it is traveling straight forward at constant speed. The drag force on a vehicle may cause an increase of the rate of fuel consumption and driving instability. The rolling resistance of the vehicle may be increased as result of the negative uplifting or downward force on the vehicle. A device named roof-fairing system has been applied to examine the reduction of aerodynamic drag force on a heavy-duty truck. As for a engineering design information, the drag-reducing system should be studied theoretically and experimentally for the best efficiency of the device. Four different types of roof-fairing model were considered in this study to investigate the aerodynamic effect on a model truck. The drag and downward force generated by vehicle has been obtained from numerical calculation conducted in this study. The forces produced on four fairing models considered in this study has been compared each other to evaluate the best fairing model in terms of aerodynamic performance. The result shows that the roof-fairing mounted truck has bigger negative uplifting or downward force than that of non-mounted truck in all speed ranges, and drag force on roof-fairing mounted truck has smaller than that of non-mounted truck. The drag coefficient $(C_D)$ of the roof-fairing mounted truck (Model-3) is reduced up to $41.3\%$ than that of non-mounted trucks (Model-1). A downward force generated by a roof-fairing mounted on a truck is linearly proportional to the rolling resistance force. Therefore, the negative lifting force on a heavy-duty truck is another important factor in aerodynamic design parameter and should be considered in the design of a drag-reducing device of a tractor-trailer. According to the numerical result obtained from present study, the drag force produced by the model-3 has the smallest of all in all speed ranges and has reasonable downward force. The smaller drag force on model-3 with 2/3h in height may results of smallest thickness of boundary layer generated on the topside of the container and the lowest intensity of turbulent kinetic energy occurs at the rear side of the container.