• Journal of computational fluids engineering
• /
• v.18 no.3
• /
• pp.8-13
• /
• 2013

Drag reduction of a running vehicle is very important issue for the energy savings and emission reduction of its power train. Especially for a solar powered electric vehicle, the drag reduction and weight lightening are two serious problems to be solved to extend its driving distance under the given energy condition. In this study, the ground effect of an airfoil shaped road vehicle was studied for an optimum body design of an ultra-light solar powered electric vehicle. Clark-Y airfoil type was adopted to the body shape of the model vehicle to reduce aerodynamic drag. From the study, it was found that the drag of the model vehicle was reduced as the height(h) between ground and the lower surface of the model vehicle was decreased. It is due to the reduction of the down-wash decreasing the induced drag of the vehicle. The lift was also decreased as the height decreased. It is due to the turbulent boundary layer developed beneath the vehicle body. The drag is classified into two types; the form and friction drag. The fraction of form drag to friction one is 76 to 24 on the model vehicle. As the height(h) of the model vehicle from the ground surface increases the form drag also increases but the friction drag is in reverse.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1712-1718
• /
• 2014

Experimental analysis according to the plasma actuator design variables was performed in order to verify the effects of sliding discharge plasma on aerodynamic drag reduction of a high-speed train. For the study, sliding discharge plasma actuator and high-frequency, high-voltage power supply were developed and experimented to figure out the best design variables for highest ionic wind velocity which could reduce the drag force. And then, 5% reduced-scale model of a high-speed train was built for wind tunnel test to verify it. From the results, it was confirmed that sliding discharge plasma had contribution to reduce the drag force and it had the potential to be applied to real-scale trains.

• Journal of the korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.56-63
• /
• 1983

The aerodynamic characteristics of the most popular car (PONY 2) produced in Korea have been experimentally investigated by Seoul National University's wind tunnel. The model (PONY 2) chosen for the wind tunnel was a 1/5 scale of the original car without simulated underbody, cooling air flow and accessories. The measured aerodynamic drag coefficient corrected by JARI formula is 0.45 which is very close to those of small foreign cars. To see the effect of the different configurations on the aerodynamic drag, the modifications have been made by changing the hood slope and backlight slope, and putting the add-on-aerodynamic devices on the orignal shape. The rear spoiler was found the most effective one to reduce the aerodynamic drag. It may be concluded that the considerable aerodynamic drag reduction can be achieved by changing the slopes and A-O-A devices at the proper places of the car.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.14-19
• /
• 2011

Wind tunnel tests are performed so as to investigate the aerodynamic drag characteristics of HEMU-400x, next generation Korean high speed train. The experiments of 1/20 scaled 5-car train model are done at 30, 40, 50, 60m/s with a normal bogie, a bogie cover, and a streamlined shape. The flat plate with knife edge are installed to minimize the effect of boundary layer of wind tunnel for the train model. The aerodynamic drag reduction was more by a streamlined shape than by a bogie cover from a normal bogie. Based on the experimental results, the aerodynamic drag of HEMU-400x test train(6-car) was predicted. It is prediceted that More bogie cover could reduce more aerodynamic drag of the test train in replacement of normal bogies.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.31-39
• /
• 1996

The effect of rear-spoiler attached at rear end of automobile trunk on the aerodynamic characteristics of a MIRA reference car model was experimentally investigated. For different shapes and positions(G/H) of the rear-spoiler, the aerodynamic forces on the automobile were measured at various flow speed(ReL). The effect of rear-spoiler on the wake structure behind the automobile was also investigated using flow visualization and hot-wire anemometer. The rear-spoiler modifies the near wake structure and decreases aerodynamic drag and increases driving stability compared with those of the conventional automobile without rear-spoiler. From the experimental results, rear-spoiler of airfoil shape installed at the position of G/H=0.084 shows the best aerodynamic performance.

• Journal of Aerospace System Engineering
• /
• v.2 no.2
• /
• pp.46-50
• /
• 2008

Aerodynamic characteristics, such as drag and lift, play an important role in automobile design under certain speed conditions. Such characteristics are essential to design an automobile since they are directly related to automobile's performance such as passenger safety and fuel consumption. There is a huge demand for the automobile to have safe performance at high speed. Reduction in drag is also important and it could lead to the solution of air flow induced noise and dust problems. The objective of this research is to find out the aerodynamic differences between conventional side mirror and a modified one using CFD. Although drag generated around a side mirror is only about 7% of the total drag when a car runs, it is very closely related to driver's field of vision and noise generation. CFD simulation of the flowfield around a car side-view mirror was performed using a commercial code; Gambit and FLUENT.

• Wind and Structures
• /
• v.22 no.5
• /
• pp.573-594
• /
• 2016

Simultaneous pressure measurements on 2D square prisms with various corner modifications were performed in uniform flow with low turbulence level, and the testing Reynolds numbers varied from $1.0{\times}10^5$ to $4.8{\times}10^5$. Experimental models were a square prism, three chamfered-corner square prisms (B/D=5%, 10%, and 15%, where B is the chamfered corner dimension and D is the cross-sectional dimension), and six rounded-corner square prisms (R/D =5%, 10%, 15%, 20%, 30%, and 40%, where R is the corner radius). Experimental results of drag coefficients, wind pressure distributions, power spectra of aerodynamic force coefficients, and Strouhal numbers are presented. Ten models are divided into various categories according to the variations of mean drag coefficients with Reynolds number. The mean drag coefficients of models with $B/D{\leq}15%$ and $R/D{\leq}15%$ are unaffected by the Reynolds number. On the contrary, the mean drag coefficients of models with R/D=20%, 30%, and 40% are obviously dependent on Reynolds number. Wind pressure distributions around each model are analyzed according to the categorized results.The influence mechanisms of corner modifications on the aerodynamic characteristics of the square prism are revealed from the perspective of flow around the model, which can be obtained by analyzing the local pressures acting on the model surface.

• Wind and Structures
• /
• v.31 no.1
• /
• pp.15-20
• /
• 2020

The aircraft industry supports aviation by building aircraft and manufacturing aircraft parts for their maintenance. Fuel economization is one of the biggest concerns in the aircraft industry. The reduction in specific fuel consumption of aircraft can be achieved by a variety of means, simplest and more effective is the one to impose minor modifications in the aircraft main wing or the parts which are exposed to the air flow. This method can lead to a reduction in aerodynamic resistance offered by the air and have a smoother flight. The main objective of this study is to propose geometric design modifications on an existing aircraft wing which acts as a vortex generator and it can reduce the drag and increase lift to drag ratio, leading to lower fuel consumption. The NACA 2412 aircraft wing is modified and designed. Rigorous flow analysis is carried out using computational fluid dynamics based software Ansys Fluent. Results show that saw tooth modification to the main wing shows the best aerodynamic efficiency as compared to other modifications.

• Journal of computational fluids engineering
• /
• v.17 no.4
• /
• pp.56-68
• /
• 2012

Nowadays, Unmanned Combat Air Vehicle(UCAV) has become an important aircraft system for the national defense. For its efficiency and survivability, shape optimization of UCAV is an essential part of its design process. In this paper, shape optimization of UCAV was processed for aerodynamic performance improvement and Radar Cross Section(RCS) reduction using Multi Objective Genetic Algorithm(MOGA). Lift and induced drag, friction drag, RCS were calculated using panel method, boundary layer theory, Physical Optics(PO) approximation respectively. In particular, calculation applied Radar Absorbing Material(RAM) was performed for the additional RCS reduction. Results are indicated that shape optimization is performed well for improving aerodynamic performance, reducing RCS. Further study will be performed with higher fidelity tools and consider other design segments including structure.

• International Journal of Aeronautical and Space Sciences
• /
• v.15 no.4
• /
• pp.374-382
• /
• 2014

This paper presents the computational aerodynamic analysis of a long-endurance UAV that was developed by the Korea Aerospace Research Institute (KARI), named EAV-2. EAV-2 is a technical demonstrator of aerodynamically efficient design, as well as a hybrid electric-propulsion system for future long-endurance UAVs. We evaluated the aerodynamic characteristics of six low-Reynolds number airfoils, using a panel method code, XFOIL, to select an optimal airfoil for the long-endurance mission of EAV-2. The computational results by a CFD code, FLUENT, suggested that the aerodynamic performance of EAV-2 would be notably improved after adopting SG6043 airfoil, and modifying the fuselage design. This reduced the total drag by 43%, compared to that of a previous KARI model, EAV-1, at the target lift of $C_L=1.0$. Also, we achieved a drag reduction of approximately 14% by means of the low-drag fuselage configuration.