• Journal of Cadastre & Land InformatiX
• /
• v.51 no.1
• /
• pp.125-136
• /
• 2021

Recently, Unmanned Aerial Vehicle utilization and image processing technology for remote sensing have diversified remarkably with Orthophoto and Digital Surface Model. In particular, It uses more application fields such as spatial information analysis and hazardous areas as well as land surveying. This study analyses the accuracy of the coordinate on Orthophoto and DSM height on slope area with high and low differences by using UAV images. As the result of this study, in the case of GCP on 2D orthophoto, the location error was not produced significantly. The vertical position of the DSM showed the highest accuracy when the height difference between GCPs is under 30m(RMSEZ=0.07m). The location of the GCPs was divided into approximately 10m, 20m, 30m, and 40m with analysis for each of the eight points of GCP and inspection points in general. This study expects that producing both horizontal accuracy of Orthophoto and vertical accuracy of DSM using UAV on the sloped area which similar to this research area will help in spatial information fields.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.2
• /
• pp.263-270
• /
• 2024

As unmanned aerial vehicles(UAVs) and sensors have been developed in a variety of ways, it has become possible to update information on the ground faster than existing aerial photography or remote sensing. However, acquisition and input of ground control points(GCPs) UAV photogrammetry takes a lot of time, and geometric distortion occurs if measurement and input of GCPs are incorrect. In this study, RGB-based orthophotos were generated to reduce GCPs measurment and input time, and comparison and evaluation were performed by applying feature point algorithms to target orthophotos from various sensors. Four feature point extraction algorithms were applied to the two study sites, and as a result, speeded up robust features(SURF) was the best in terms of the ratio of matching pairs to feature points. When compared overall, the accelerated-KAZE(AKAZE) method extracted the most feature points and matching pairs, and the binary robust invariant scalable keypoints(BRISK) method extracted the fewest feature points and matching pairs. Through these results, it was confirmed that the AKAZE method is superior when performing geometric correction of the objective orthophoto for each sensor.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.16 no.2
• /
• pp.243-250
• /
• 1998

From early plane-table photogrammetry through the analog and analytical stages, photogrammetry has now reached the digital photogrammetry stage using the image stored at computers. Digital Photogrammetry using aerial photograph generates the DTM and digital orthophoto. Expecially, DTM is important for improving the accuracy of digital ortho photo. so Many experimental are required. In this study, therefore deals with the generation process of digital orthophotos using DTM with breakline and without breakline.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.17 no.2
• /
• pp.97-104
• /
• 1999

Digital elevation models(DEMs) represent an important data base for orthophoto generation The quality of a DEM depends on the geometrical accuracy of the original point or line data. This study analyzes the effects of grid space and scanning resolution in DEM creation with image matching method. The less standard deviation of DEM error was introduced when we adopted small grid space, but no effects in scanning resolution. Based on the bias error analysis of the DEM, we found that the error of a large scale of aerial photograph was bigger than that of a small scale case, and that such error mainly came from the closed area in large scale photographs. In order to reduce the closed area, the experiment has been conducted using multi scale and different overlap of aerial photo images. The result shows that the size of closed area and the shaded area has been dramatically decreased due to the adoption of multi scale aerial images instead of a couple of stereo images.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.36 no.4
• /
• pp.263-270
• /
• 2018

Land surface temperature is known to be an important factor in understanding the interactions of the ground-atmosphere. However, because of the large spatio-temporal variability, regular observation is rarely made. The existing land surface temperature is observed using satellite images, but due to the nature of satellite, it has the limit of long revisit period and low accuracy. In this study, in order to confirm the possibility of replacing land surface temperature observation using satellite imagery, images acquired by TIR (Thermal Infrared) sensor mounted on UAV (Unmanned Aerial Vehicle) are used. The acquired images were transformed from JPEG (Joint Photographic Experts Group) to TIFF (Tagged Image File Format) format and orthophoto was then generated. The DN (Digital Number) value of orthophoto was used to calculate the actual land surface temperature. In order to evaluate the accuracy of the calculated land surface temperature, the land surface temperature was compared with the land surface temperature directly observed with an infrared thermometer at the same time. When comparing the observed land surface temperatures in two ways, the accuracy of all the land covers was below the measure accuracy of the TIR sensor. Therefore, the possibility of replacing the satellite image, which is a conventional land surface temperature observation method, is confirmed by using the TIR sensor mounted on UAV.

• Journal of Korean Society for Geospatial Information Science
• /
• v.5 no.2 s.10
• /
• pp.207-220
• /
• 1997

This study aims to develope the production method of digital image map of high capable utiliy and terrain interpretability using aerial photo and Geospatial Information System. Theory and efficient practical method was studied to generate tile digital image map with low-cost personal computer system using the merging procedure of raster scanned aerial photo and vector topographic map. Determination theory of ground coordinates, digital image processing, production of digital elevation model was reviewed. And some chariteristics of digital image map, image collection method and significant concepts of digital image processing was studied. Also input and output way of image data to generate the digital image nap, production method of orthophoto map using aerial photo through digital differential rectification was studied. As the result, digital image map was produced and analyzed through the above mentioned procedures.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.16 no.1
• /
• pp.10-17
• /
• 2004

In this paper, the affine transformation method that is more simpler compare with digital orthophoto method is used analyzed the long-term shoreline change, and accuracy estimation was carried out. As a result of this study, it was able to check that the shoreline change on Namhangjin coast had eroded significantly compare with the past. Moreover, as a result of accuracy estimation, it shows that the RMS error around shoreline was about 1-2 m. In consideration that maximum allowable error shown in aerial photogrammetry specification is within 2 m, therefore, analysis results of shoreline change using affine transformation method on aerial images is reliable.

• Spatial Information Research
• /
• v.13 no.1 s.32
• /
• pp.55-63
• /
• 2005

Direct Georeferencing(DG) Is based on the direct measurement of the projection centers and rotation angle of sensor through loading the GPS and INS in aircraft. The methods can offer us to acquire the exterior orientation parameters with only minimum GCPs, even the ground control process could be completely skipped. Hence, as long as securing Digital Elevation Model (DEM), it is feasible to generate digital orthophotos without performing the aerial triangulation with Ground Control Point (GCP) surveying. In this study, the DEM is automatically generated by using a image matching technique based on aerial photos and exterior orientation parameters. This is followed by producing an orthophoto from these results. Finally, accuracy analysis of the georeferencing technique for generating orthoimage indicates that RMS errors of 62cm and 76cm occurred at the X and the Y axis, respectively. This means that the results fulfill the demanding accuracy of the 1:5000 digital map. Hence, it is possible to conclude from this study that the direct georeferencing based orthoimage generation method is able to effectively digital map update.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.36 no.3
• /
• pp.117-126
• /
• 2018

Due to intelligent transport systems, location-based applications, and augmented reality, demand for image maps and 3D (Three-Dimensional) maps is increasing. As a result, data acquisition using UAV (Unmanned Aerial Vehicles) has flourished in recent years. However, even though orthophoto map production and research using UAVs are flourishing, few studies on 3D modeling have been conducted. In this study, orthophoto and 3D modeling research was performed using various angle images acquired by a UAV. For orthophotos, accuracy was evaluated using a GPS (Global Positioning System) survey that employed VRS (Virtual Reference Station) acquired checkpoints. 3D modeling was evaluated by calculating the RMSE (Root Mean Square Error) of the difference between the outline height values of buildings obtained from the GPS survey to the corresponding 3D modeling height values. The orthophotos satisfied the acceptable accuracy of NGII (National Geographic Information Institute) for a 1/500 scale map from all angles. In the case of 3D modeling, models based on images taken at 45 degrees revealed better accuracy of building outlines than models based on images taken at 30, 60, or 75 degrees. To summarize, it was shown that for orthophotos, the accuracy for 1/500 maps was satisfied at all angles; for 3D modeling, images taken at 45 degrees produced the most accurate models.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.100-102
• /
• 2003

This system is capable of obtaining quantitative information from images using natural features on the ortho-image maps that correspond with those from topographical maps. However, the qualitative information can also be obtained because because of the excellent visibility of ortho-image maps. There are plenty of promise for the use of ortho-image maps in the next generation topographic technology because of its wider applicability within the field. In keeping with the cutting edge, we produced ortho-image maps by scanning a specified area in narrow sections using the PKNU 2: a multispectral digital aerial photographing system made by ourselves. We evaluated the precision of the ortho-image maps, and performed an evaluation of the PKNU 2 system's capacity to improve the equipment of the PKNU 2. Ortho-image maps were made using Ground Control Points (GCPs) which were obtained from digital maps and aerial photographs of the PKNU 2. Thus, we demonstrated that it was possible to produce the ortho-image maps, which has a good constant level rate of less than 1m. The PKNU 2 system needs to be improving in the sensitivity of level maintenance equipment in the evaluation in terms of performance. It is thus required to survey the GCPs precisely for an accurate study.