• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.6
• /
• pp.1011-1019
• /
• 2000

The purpose of this study is to examine the basis of design condition of existing treatment processes, namely, Extended Aeration Process, Conventional Activated Process, High Rate Aeration Process and Modified Aeration Process, by clarifying the correlations of influent wastewater concentration, hydraulic retention time, food-to-microorganism ratio and sedimentation of sludge, as well as to ascertain the feasibility of design, regardless of the existing design condition. In particular, this study made a priority investigation of hydraulic retention time and sludge sedimentation, because sludge sedimentation is the main factor$^{1)}$ which determines the operating conditions of existing treatment processes. Therefore, it is generally known that in case exceeds the sphere of design presented for each treatment, sludge bulking may occur. The results of Lesperance's test$^{1)}$, which formed the basis of design, showed the sphere of loading without security of sludge sedimentation, as in Fig. 1. The reason for sludge bulking in a certain condition, as above, is due to failure in application of optimum loading corresponding to each retention time by employing a few operating condition, which proved to be consecutively workable after years of trials and failures by Lesperance, for test conditions. However, the result of this test showed that in case of proper maintenance of loading. sludge sedimentation can be ensured under 120 SVI. Therefore, this study suggested hydraulic retention time and its corresponding optimum loading, and identified the hydraulic retention time as a determinant of sludge sedimentation. And. on the basis of these findings, this study suggested the feasiblity of UHR(Ultra High Rate), a new operating process, exceeding several times the applicable loading value of High Rate Aeration Process under one hour retention time which has not yet applied to the existing treatment processes.

• Membrane Journal
• /
• v.1 no.1
• /
• pp.100-100
• /
• 1991

A novel system to thicken the concentrated colloidal solution from membrane water treat-ment processes was developed. A hollow-fiber microfilter(hydrophilic polyethylene nominal pore size 0.1 μm total surface area 0.42 m2) was installed in an acrylic housing that has an aeration port 5 cm below the membrane and a clarifier in the bottom. The concentrate was uniformly supplied from the top of the housing. Bacuum filtration caused downward flow of concentrate and as a result thickening interface. The addition of poly-aluminum chloride (PAC) resulted in rapid increase of trans-membrane pressure (TMP) and in no improvement of the filtered water turbidity and thickening process. Two types of con-centrate and concentrate turbidity had little effect on the increase of TMP and concentrate thickening. It was observed that for the same height of membrane housing membrane surface area to housing volume (A/V) ratio had significant effect on the increase of TMP. When the housing volume was increased ten times the increasing rate of TMP was three times faster as compared to the original housing. A hydraulic model successfully simulated the formation and sedimentation of thickening interface.

• Korean Journal of Soil Science and Fertilizer
• /
• v.49 no.5
• /
• pp.461-468
• /
• 2016

One of the important phytohormones produced by plant growth promoting bacteria is the auxin; indole-3-acetic acid (IAA), with L-tryptophan as the precursor. In this study, we focused on the investigation of optimal conditions for the production of IAA by Bacillus megaterium BM5. We investigated culturing conditions, such as incubation temperature, pH of the culture medium and incubation period, with varying media components such as inoculation volume, tryptophan concentration and carbon and nitrogen source. Besides, optimization study intended for high IAA production was carried out with fermentation parameters such as rpm and aeration. The initial yield of $42{\mu}g\;IAA\;ml^{-1}$ after 24 hr increased to $85{\mu}g\;ml^{-1}$ when 5% (v/v) of L-tryptophan was used in the culture broth. The maximum yield of $320{\mu}g\;IAA\;ml^{-1}$ was observed in trypticase soy broth (TSB) supplemented with starch and soybean meal as C and N sources with a C/N ratio of 3:1 (v/v) at $30^{\circ}C$, pH 8.0 for 48 hrs with 1.0 vvm and 250 rpm in 5 L working volume using 10 L scale fermenter. The bacterial auxin extracted from the culture broth was confirmed by thin layer chromatography and high-performance liquid chromatography and effect on plant growth was confirmed by root elongation test.

• Environmental Engineering Research
• /
• v.24 no.3
• /
• pp.382-388
• /
• 2019

Although nanobubbles attract significant attention, their characteristics and applications have not been thoroughly defined. There are diverse opinions about the definition of nanobubbles and controversy regarding methods that verify their characteristics. This study defines nanobubbles as having a size less than $1{\mu}m$. The generation of these sub-micron (nano) bubbles may be verified by induced coalescence or light scattering. The size of a sub-micron (nano) bubbles may be measured by optical, and confocal laser scanning microscopy. Also, the size may be estimated by the relationship of bubble size with the dissolved oxygen concentration. However, further research is required to accurately define the average bubble size. The zeta potential of sub-micron (nano) bubbles decreases as pH increases, and this trend is consistent for micron bubbles. When the bubble size is reduced to about 700-900 nm, they become stationary in water and lose buoyancy. This characteristic means that measuring the concentration of sub-micron (nano) bubbles by volume may be possible by irradiating them with ultrasonic waves, causing them to merge into micron bubbles. As mass transfer is a function of surface area and rising velocity, this strongly indicates that the application of sub-micron (nano) bubbles may significantly increase mass transfer rates in advanced oxidation and aeration processes.

• Journal of Animal Science and Technology
• /
• v.45 no.5
• /
• pp.875-884
• /
• 2003

Operational parameters for struvite crystallization, as a process to recover nitrogen and phosphorus resources from animal wastewater, were studied in this research. Crystallization distinctive of NH$_4$-N and PO$_4$$^{3-}$ in accordance to chemical sources, influent pH, aeration and stirring was examined using 2L of working volume of struvite reactor. Also, to find an effective treatment process combining with electrolysis method, removal characteristics of NH$_4$-N and PO$_4$$^{3-}$ in 6 different processes was tested. As chemical sources for the derivation of struvite formation, MgSO$_4$ and MgCl$_2$ were superior to CaCO$_3$ and CaCl$_2$. From experiment which was conducted to know the effects of aeration and stirring on struvite formation, it was revealed that aeration stimulated the crystallization reaction by inducing faster pH increase. While 90% of P removal was achieved within 1 hour under aeration, 14 hours was consumed under stirring condition. Struvite formation under aeration was affected by influent pH. No crystallization was observed at pH 5 level, but active crystallization reaction was induced over pH 6.0. 95% of P removal by struvite formation at pH 6, 7 and 9 was achieved within 3h, 2h and 10 min., respectively. However, over pH 10, operational problem due to excessive foam formation occurred, and blunting of crystallization reaction was observed at pH 11. When consider the pH range of animal wastewater, pH 7 to 9, efficient struvite formation could be achieved by simple aeration, without any chemical usage for pH adjustment. Among tested processes, the treatment process which electrolyzing the supernatant from struvite reactor, providing air to both reactors, showed best pollutant removal efficiencies. In this combined process, the removal efficiencies of NH$_4$-N and PO$_4$$^{3-}$ was 86% and 98%, respectively, and 92.4% of color removal was obtained.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.12
• /
• pp.2239-2245
• /
• 2000

For the treatment of wastewater being discharged in large quantities as in these modern times, qualitative and quantitative concepts should be introduced in consideration of the recycling. In view of a qualitative concept, high rate aeration process is known as the most effective process up to now. However, Lee suggested UHR process showing the superiority over high rate process in treatment rate and quantity. Therefore, this study was performed to investigate the basic sphere of design and treatment quality, such as applicable $BOD_5$-loading and influent wastewater concentration of UHR process, based on Lee's suggestions1). Consequently, this process showed applicable $BOD_5$-loading of $2.2{\sim}7.0kg-BOD_5/kg-MLSS{\cdot}day$, exceeding three times or more of high rate process with maximum applicable loading of $2.25kg-BOD_5/kg-MLSS{\cdot}day$. Meanwhile, with the range of influent wastewater concentration from 200 to 450 mg/L. it showed the treatment rate from 94.7 to 97.3%, it indicated very good condition. In view of quantitative concept of treatment, UHR process is considered an epoch-making treatment process being superior to existing ones.

• KSTLE International Journal
• /
• v.2 no.2
• /
• pp.103-113
• /
• 2001

The influence of aerated oil on high-speed journal bearing is examined by classical thermohydrodynamic lubrication theory coupled with analytical models for viscosity and density of air-oil mixture in fluid-film bearing. Convection to the walls and mixing with supply oil and re-circulating oil are considered. The live oil surface tension is considered as functions of temperature, API gravity and air volume ratio. With changing eccentricity ratio, it is investigated the effects of air bubbles on the performance of a high-speed plain journal bearing. Just at the moderate eccentricity ratios, even if the involved aeration levels are not so severe and the entrained air bubble sizes are not so small, it is found that the bearing load and friction farce may be changed so visibly for the high speed bearing operation.

• Microbiology and Biotechnology Letters
• /
• v.25 no.1
• /
• pp.68-74
• /
• 1997

The conversion of D-sorbitol to L-sorbose by Gluconobater suboxydans was analyzed, and continuous production of L-sorbose was carried out in immobilized cell reactors. L-Sorbose production by high densities of resting cells was more effective than by conventional batch fermentations. Sorbitol dehydrogenase, an enzyme converting D-sorbitol to L-sorbose, did not suffer from substrate inhibition, but from product inhibition. When L-sorbose production was carried out with Ca-alginate-immobilized cells, about 60 g/l of L-sorbose was obtained. On the other hand, when the corn steep liquor (CSL) concentration of medium was reduced to 0.08%, 80 g/l of L-sorbose was obtained. Outgrowth inside the immobilized carriers was thought to block the pores of the carriers so that substrate could not easily diffuse through the carriers. Continuous production of L-sorbose was well accomplished in a bubble column reactor, and 6. 5 g/l.h of productivity and 81.2% of yield were obtained at a substrate feeding rate of 0.08h$^{-1}$ under the optimum conditions with carrier volume of 55% and aeration rate of 3 vvm.

• Environmental Engineering Research
• /
• v.16 no.1
• /
• pp.47-51
• /
• 2011

The oxygen transfer rate is a parameter that characterizes the gas-liquid mass transfer in surface aerators. Gas-liquid transfer mechanisms in surface aeration tanks depend on two different extreme lengths of time; namely, macromixing and micromixing. Small scale mixing close to the molecular level is referred to as micromixing; whereas, macromixing refers to mixing on a large scale. Using experimental data and numerical simulations, macro- and micro-scale parameters describing the two extreme time scales were investigated. A scale up equation to simulate the oxygen transfer rate with micromixing times was developed in geometrically similar baffled surface aerators.

• Journal of Environmental Science International
• /
• v.8 no.4
• /
• pp.479-483
• /
• 1999

Nitrifier consortium immobilized in polyvinyl alcohol was used for the removal of ammonia nitrogen from synthetic aquaculture water in the airlift bioreactor. At the aeration rate fo 0.15 vvm and bead packing volume fraction of 20%, airlift bioreactor was operated effectively for a removal of ammonia nitrogen and for a stability of operation. Ammonia nitrogen removal rate by airlift bioreactor was continuously increased with decreasing hydraulic residence time. At the HRT(hydraulic residence time) of 0.3 hour, ammonia nitrogen removal rate was 84.3 g/$m^3$.d and the highest ammonia nitrogen removal rate was 130.8 g/$m^3$.d when HRT was 0.1 hour.