• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.448-455
• /
• 2005

In this paper, an analytical model for estimation of the time at which the concrete surface begins to dry is introduced to predict whether or not plastic shrinkage cracks occur. First of all, the validity of a consolidation model for bleeding of cement paste proposed by Tan et al. is verified by comparing the analytical results with the experimental results, and used to evaluate the rate and amount of bleed water of concrete. Also an analytical model for evaporation of bleed water which considers the effect of the temperature variation of concrete surface due to hydration heat on the evaporation rate is proposed, and the experimental and analytical results are then compared to verify the validity of the introduced model. In advance, the time at which the concrete surface begins to dry is estimated using above two analytical models, and compared with the experimental results about the time at which plastic shrinkage cracks occur. From the comparison, it is verified that the proposed model can predict the occurrence of plastic shrinkage cracking with comparative precision.

• 간호행정학회지
• /
• 제22권5호
• /
• pp.415-423
• /
• 2016

Purpose: The purpose of this research was to provide patients with safe preoperative preparatory procedures by removing any risk factors from the preparatory procedures by using failure mode and effects analysis, which is a prospective risk-managing tool. Methods: This was a research design in which before and after conditions of a single group were studied, Failure mode and effects analysis were applied for the preparatory procedures done before operations. Results: The preparation omission rate before the operation decreased from 2.70% to 0.04%, and operation cancellation rate decreased from 0.48% to 0.08%. Conclusion: Failure mode and effects analysis which remove any risk factors for patients in advance of the operation is effective in preventing any negligent accidents.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.1059-1064
• /
• 2001

This study is about accurate steel column position method in the Top down method's delicate part. When the concrete is placing, it is required that complementary measures to the transformation due to concrete pressure, column buckling, the trouble due to bar net inserting and so on. To solve the problem of exist method, the concrete is placed at the bottom of excavated hole in advance. then, the steel column is inserted into the excavated hole. With a new method try, the problem due to placing pressure and others is could be prevented. In this study, the concrete is examined with test-slump, slump flow, and compressive strength to do quantitative analysis of concrete. The factors of the experiment is plasticizer, retarder addition rate, fly ash substitution rate to cement. Considering of the new method try, the retarder added concrete properties-fluidity, viscosity, strength-is investigated as time lapsing.

• 가정과삶의질연구
• /
• 제8권1호
• /
• pp.49-67
• /
• 1990

The purpose of this study is to investigate the relations between marital status incompatibility and the ways of dealing with marital conflict. Research was conducted by interview using questionnaire on 177 employed wives. Statistics used for data analysis were frequency distribution, percentage, t-test, chi-square test. 1) In resolving marital conflict four types of method are appeared, namely constructive method, passive method, evasion and physical violence. 2) Only physical violence of husband-to-wife of the four methods is related to status in-compatibility. That is the incidence rate of physical violence of husband-to-wife in incompatible couples is higher than that of compatible couples in conflict situations. 3) In case the wife's occupational status is high relative to her husband the incidence rate of physical violence of husband-to-wife is extremely high, but is significantly low in couples which are compatible in this status. 4) In case wife's status advance ent is controlled, there is significant relationship between status incompatibility and the method of conflict resolution by husband whose wife is status striver.

• 한국동물학회:학술대회논문집
• /
• 한국동물학회 1995년도 제16회 생물과학 심포지움 강연록
• /
• pp.68-73
• /
• 1995

Most female Great Tits lay one egg each day until the clutch is complete. However, some exceptions are found. “Pause day/s” most frequently occur after the 1st egg is laid. In general, egg-size increase with laying sequence, but there is year-to-year variation. The relationship between egg size and laying sequence is found more significantly in relatively larger clutches than in smaller ones. Great Tits tend to advance the hatching of their chicks by starting to incubate earlier in relation to clutch completion as the breeding season progresses. hatching asynchrony affects chick´s growth rate, but when the effect of laying date on hatching asynchrony is controlled, the effect of hatching asynchrony on growth rate is not found. These findings support the ´hurry-up´ hypothesis.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제13권1호
• /
• pp.385-405
• /
• 2019

High Efficiency Video Coding (HEVC) enables significantly improved compression performance relative to existing standards. However, the advance also requires high computational complexity. To accelerate the intra prediction mode decision, a minimum risk Bayesian classification framework is introduced. The classifier selects a small number of candidate modes to be evaluated by a rate-distortion optimization process using the sum of absolute Hadamard transformed difference (SATD). Moreover, the proposed method provides a loss factor that is a good trade-off model between computational complexity and coding efficiency. Experimental results show that the proposed method achieves a 31.54% average reduction in the encoding run time with a negligible coding loss of 0.93% BD-rate relative to HEVC test model 16.6 for the Intra_Main common test condition.

• Design & Manufacturing
• /
• 제14권4호
• /
• pp.52-57
• /
• 2020

In this study attempted to prevent defects due to blow holes among defects of sand casting products. It was intended to reduce the defect rate by reducing the blow hole of the inner surface. Currently, expectations and requirements for the quality level of non-ferrous aluminum casting in the casting industry are increasing. In addition, the shape is complex and the shrinkage precision is required. Among them, the test prototype is expensive to manufacture the mold, and the production time is also long, and the product is manufactured by sand casting. At this time, the highest defect rates are defects caused by shrinkage defects, surface defects, and blow holes.. At this study, the manufacturing time was shortened by using the shape of the fluid movement path in advance. Also, it is possible to reduce defects due to blow holes.

• 국제학술발표논문집
• /
• The 2th International Conference on Construction Engineering and Project Management
• /
• pp.554-562
• /
• 2007

This study determined tact process paths by separating the finish works according to the properties of work areas and work relations in order to apply the tact schedule management to the finish works. In addition, by suggesting preparing and sharing the workflow charts, the experiments can be shared between the executors and any possible frictions between the specialist works can be identified in advance. In addition, any errors on the plan can be reviewed and modified through the measurement stage of tact plan attainment rate. The process of tact schedule management is improved with such tools and methods and the efficiency of the process through the application of cases was verified.

• 한국컴퓨터정보학회논문지
• /
• 제14권9호
• /
• pp.29-35
• /
• 2009

본 논문에서는 AODV(Ad hoc On demand Distance Vector)에 기초한 트래픽 관리 이동 애드 혹 라우팅 프로토콜을 제안하고 시뮬레이션을 통하여 성능을 평가한다. 각 노드에서 사용 가능한 통신 자원을 미리 고려하여 트래픽 관리에 적합한 최단경로를 설정함으로써 평균데이터수신율을 증가시킨다. 성능평가를 위해, 노드들의 이동성을 고려하여 평균데이터수신율을 분석한다.

• 한국농공학회지
• /
• 제39권6호
• /
• pp.67-79
• /
• 1997

The perpose of this study was to suggest the experimental characteristic of the Cherepnov Water Lifter following the drain mode. The Cherepnov Water Lifter(CWL), which is powered by the potential energy of water, can be set to operate automatically when the water m a tank is drained. In this study, a CWL is constructed in the valve drain controlling mode(VCM) and the siphon drain controlling mode(SCM), and a pressure transducer is installed. It was found that, in the VCM, intake flow volume is proportional to both delivery flow volume and drain flow volume. In the SCM, intake flow volume is proportional to drain flow volume, and the average delivery rate is proportional to both efficiency and the water utilization ratio. Also, in the VCM, the water utilization ratio is 35~49%, efficiency is 62~9O%, average delivery rate is 12.8~81.2$cm^3$/s, and the average drain rate is 14.O~91.5c$cm^3$/s. On the contrary in the SCM, the water utilization ratio is 1.7~38%, efficiency is 3~58%, average delivery rate is 3.1 ~69.2$cm^3$/s, and the average drain rate is shown as 114.5~ 183$cm^3$/s. As a result of the water utilization ratio, efficiency, average delivery rate, and average drain rate are compared, the VCM is found to be superior and the more economical mode. However, the VCM requires manpower and electricity to operate the electronic machinery involved, while the SCM requires no manpower or electricity at all. An economic evaluation of these differences will be necessary in the future. Also, in the SCM, studies to improve water utilization ratio and efficiency, to find the optimum height of the siphon for decreasing the average drain rate, and to determine the radius of curvature of throat have to be conducted in advance, since a large flow rate is drained during the priming action of the siphon.