• Carbon letters
• /
• 제8권3호
• /
• pp.199-206
• /
• 2007

The activated carbon produced from rubber wood sawdust by chemical activation using phosphoric acid have been utilized as an adsorbent for the removal of Cu(II) from aqueous solution in the concentration range 5-40 mg/l. Adsorption experiments were carried out in a batch process and various experimental parameters such as effect of contact time, initial copper ion concentration, carbon dosage, and pH on percentage removal have been studied. Adsorption results obtained for activated carbon from rubber wood sawdust were compared with the results of commercial activated carbon (CAC). The adsorption on activated carbon samples increased with contact time and attained maximum value at 3 h for CAC and 4 h for PAC. The adsorption results show that the copper uptake increased with increasing pH, the optimum efficiency being attained at pH 6. The precipitation of copper hydroxide occurred when pH of the adsorbate solution was greater than 6. The equilibrium data were fitted using Langmuir and Freundlich adsorption isotherm equation. The kinetics of sorption of the copper ion has been analyzed by two kinetic models, namely, the pseudo first order and pseudo second order kinetic model. The adsorption constants and rate constants for the models have been determined. The process follows pseudo second order kinetics and the results indicated that the Langmuir model gave a better fit to the experimental data than the Freundlich model. It was concluded that activated carbon produced using phosphoric acid has higher adsorption capacity when compared to CAC.

• Carbon letters
• /
• 제19권
• /
• pp.12-22
• /
• 2016

Date palm leaflets were used as a precursor to prepare dehydrated carbon (DC) via phosphoric acid treatment at 150℃. DC, acidified with H₃PO₄, was converted to activated carbon (AC) at 500℃ under a nitrogen atmosphere. DC shows very low surface area (6.1 m²/g) while AC possesses very high surface area (829 m²/g). The removal of lisinopril (LIS) and chlorpheniramine (CP) from an aqueous solution was tested at different pH, contact time, concentration, and temperature on both carbons. The optimal initial pH for LIS removal was 4.0 and 5.0 for DC and AC, respectively. However, for CP, initial pH 9.0 showed maximum adsorption on both carbons. Adsorption kinetics showed faster removal on AC than DC with adsorption data closely following the pseudo second order kinetic model. Adsorption increases with temperature (25℃–45℃) and activation energy (E_a) is in a range of 19–25 kJ mol/L. Equilibrium studies show higher adsorption on AC than DC. Thermodynamic parameters show that drug removal is endothermic and spontaneous with physical adsorption dominating the adsorption process. Column adsorption data show good fitting to the Thomas model. Despite its very low surface area, DC shows ~70% of AC drug adsorption capacity in addition of being inexpensive and easily prepared.

• 한국물환경학회지
• /
• 제25권3호
• /
• pp.459-463
• /
• 2009

The adsorption features of malachite green onto activated carbon have been investigated for its treatment from aqueous solution. The influential factors were examined the initial concentration of malachite green, reaction temperature, and pH. Under experimental conditions, adsorption equilibrium of malachite green was attained within 2 hr after the adsorption started. The adsorption reaction of malachite green followed the pseudo-second order rate model, and the adsorption rate constants(k2) decreased with increasing initial concentrations of malachite green. Adsorption behavior of malachite green on activated carbon was found to follow the Freundlich model well in the initial adsorbate concentration range. With increase in temperature, the adsorbed amount of malachite green at equilibrium increased, which indicate that the adsorption reaction was endothermic reaction. Thermodynamic parameters for malachite green adsorption reaction were estimated at varying temperatures, and in the pH range of 2-10, adsorption of malachite green increased.

• Korean Chemical Engineering Research
• /
• 제55권6호
• /
• pp.771-777
• /
• 2017

Carbon nano tubes (CNTs)를 흡착제로 사용하여 회분식 실험을 통해 염료 Eosin Y의 흡착특성을 조사하였다. 본 연구에 사용된 CNTs는 비표면적이 $106.9m^2/g$, 기공부피는 $1.806cm^3/g$, 기공직경은 $163.2{\AA}$이었다. CNTs를 이용한 Eosin Y의 흡착실험은 흡착시간, 초기 pH (2~10), 염료 농도(100, 150 및 200 mg/L), 흡착제의 양(0.05~1.0 g)과 온도(293, 313 및 333 K)를 변수로 사용하여 수행하였다. 흡착은 pH와 온도가 낮을수록 잘 이루어졌으며, Langmuir 모델식에 잘 적용되었다. 또한 흡착반응은 유사 2차 속도식에 잘 적용되었으며, 온도가 증가함에 따라 흡착량이 감소하였다. 입자 내 확산 모델 결과는 흡착 과정에서 막확산과 입자확산이 동시에 일어나는 것을 시사해 주었다. 열역학적 해석에 의하면 CNTs에 의한 염료 Eosin Y의 흡착은 자발적이고 흡열특성을 보였다.

• Korean Chemical Engineering Research
• /
• 제54권2호
• /
• pp.255-261
• /
• 2016

활성탄을 사용한 Acid Yellow 14 염료의 흡착 실험은 흡착제의 양, pH, 초기농도, 접촉시간과 온도를 흡착변수로 사용하여 수행하였다. 흡착평형자료는 Langmuir, Freundlich 및 Temkin 등온식을 사용하여 해석하였는데, Freundlich 식이 가장 좋은 일치도를 나타냈다. 평가된 Freundlich 상수(1/n=0.129~0.212)와 Langmuir 분리계수($R_L=0.202{\sim}0.243$)로부터 활성탄에 의한 Acid Yellow 14의 흡착조작은 적절한 처리방법이 될 수 있음을 알았다. Temkin의 흡착열관련상수(B)는 5.101~9.164 J/mol로 평가되어, 흡착공정이 물리흡착임을 알았다. 흡착속도실험자료를 유사일차반응속도식과 유사이차반응속도식에 적용해 본 결과, 흡착동력학은 유사이차반응속도식에 잘 맞는 것으로 나타났다. Gibbs 자유에너지(-4.81~-10.33 kJ/mol)와 엔탈피(+78.59 kJ/mol)는 흡착이 자발적이고 흡열공정으로 진행된다는 것을 나타낸다.

• 공업화학
• /
• 제30권2호
• /
• pp.190-197
• /
• 2019

활성탄을 사용하여 수용액으로부터 메틸 그린 염료의 흡착에 대해 초기농도와 접촉시간 및 온도를 흡착변수로 사용하여 조사하였다. 흡착평형관계는 Freundlich 등온식에 잘 맞았다. 평가된 Freundlich 분리계수(1/n = 0.212~0.305)로부터 이 흡착공정이 효과적인 처리영역(0 < $R_L$ < 1)에 속하는 것을 알았다. BET식으로부터 얻은 등온포화용량은 온도가 증가할수록 커졌다. Dubinin-Radushkevich식으로 구한 흡착에너지값(E = 316.869~340.049 J/mol)으로부터 흡착공정이 물리흡착공정임을 알았다. 흡착속도실험결과는 유사 2차 반응속도식에 잘 맞는 것으로 나타났다. 자유에너지(-5.421~-7.889 kJ/mol)와 엔탈피(31.915 kJ/mol)는 흡착공정이 자발적이고 흡열반응으로 진행되었다고 알려주었다. 등량흡착열은 평형흡착량이 증가함에 따라 커졌으며, 표면 덮임이 증가됨에 따라 흡착제-흡착질의 총 상호작용도 증가하였다.

• 설비공학논문집
• /
• 제25권12호
• /
• pp.660-667
• /
• 2013

This study presents a numerical investigation of the heat and mass transfer kinetics of a fin-tube-type adsorption bed using a two-dimensional numerical model with silica-gel and water as the adsorbent and refrigerant pair. The performance is strongly affected by the heat and mass transfer in the adsorption bed, but the details of the mass transfer kinetics remain unclear. The validity of inter-particle models used to simulate mass-transfer kinetics were examined, such as a constant pressure model and non-constant pressure model, and the valid ranges of the diffusion ratio for each model are proposed. The COP and SCP have been numerically calculated as the performance indexes according to the diffusion ratio. The constant pressure model, which is commonly used in previous research, was found to be valid only in a limited range of diffusion ratio.

• Carbon letters
• /
• 제10권1호
• /
• pp.23-32
• /
• 2009

The adsorption of phenolic compound resorcinol on activated carbons prepared from Moringa oleifera (Drumstick bark) has been investigated. Activated carbon was prepared by impregnating Moringa oleifera with 50% phosphoric acid in the ratio of 1:1 and 1:2(w/w), designated as MOAC1 and MOAC2. Equilibrium and isotherm studies were carried out. The influences of variables such as contact time, initial concentration of resorcinol, carbon dosage in the solution on percentage adsorption and adsorption capacity of the bark have been analysed. The equilibration time was found to be 4 h. Kinetics of resorcinol onto activated carbons was checked for pseudo first order and pseudo second order model. It was found that the adsorption of resorcinol follows pseudo second order kinetics for both MOAC1 and MOAC2. The isotherm data were correlated with isotherm models, namely Langmuir and Freundlich. Adsorption isotherms were satisfactorily fitted by both the Langmuir and Freundlich model for MOAC1 and MOAC2.

• 한국환경과학회지
• /
• 제23권6호
• /
• pp.1143-1149
• /
• 2014

The adsorption experiments of lithium ions were conducted in the fixed bed column packed with activated carbon modified with nitric acid. Effect of inlet concentration, bed hight and flow rate on the removal of lithium ions was investigated. The experimental results showed that the removal and the adsorption capacity of lithium ions increased with increasing inlet concentration, and decreased with increasing flow rate. When the bed height increased, the removal and the adsorption capacity increased. The breakthrough curves gave a good fit to Bohart-Adams model. Adsorption capacity and breakthrough time calculated from Bohart-Adams model, these results were remarkably consistent with the experimental values. The adsorption capacity was not changed in the case of 3 times repetitive use of adsorbent.

• 통합자연과학논문집
• /
• 제4권2호
• /
• pp.130-136
• /
• 2011

This study investigated the adsorption characteristics of nickel, zinc and cadmium ions from the aqueous solution onto the alginate bead. Adsorption equilibrium capacities of the heavy metal ions increased with increasing initial pH of the solution. The adsorption equilibrium isotherm of the heavy metal ions was well represented by Langmuir equation. The magnitude of adsorption capacity of the heavy metal ions onto alginate bead was the order of cadmium > zinc > nickel. Kinetic parameters were measured in a batch adsorber to analyze the adsorption rates of the heavy metal ions. The internal diffusion coefficient of the heavy metal ions in the intraparticle were determined by comparing the experimental concentration curves with those predicted from the surface diffusion model (SDM) and pore diffusion model (PDM). The internal diffusion of the heavy metal ions in the intraparticles was explained by PDM.