• Journal of Integrative Natural Science
• /
• v.6 no.2
• /
• pp.104-110
• /
• 2013

1-Aza-12-crown-4 macrocyclic ligand was combined with styrene (2th petroleum in 4th class hazardous materials) divinylbenzene copolymer having 1%, 2%, 3%, and 6% crosslinks by a substitution reaction, in order to synthesize resin. These synthetic resins were confirmed by chlorine content, elementary analysis and IR-spectrum. As the results of the effects of pH, equilibrium arrival time, crosslink of synthetic resin, and dielectric constant of a solvent on uranium ion adsorption for resin adsorbent, the uranium ion showed high adsorption at pH 3 or over and adsorption equilibrium of uranium ion was about 2 hours. In addition, adsorption selectivity for the resin in methanol solvent was the order of uranium ($UO_2{^{2+}}$) > iron ($Fe^{3+}$) > lutetium ($Lu^{3+}$) ions, adsorbability of the uranium ion was in the crosslinks order of 1%, 2%, 3%, and 6% was increased with the lower dielectric constant.

• Environmental Engineering Research
• /
• v.24 no.1
• /
• pp.99-106
• /
• 2019

Using the abandoned agricultural by-product corncobs, the most commonly used methylene blue (MB) dyestuffs were removed. This experiment is very meaningful because it is the recycling of resources and the use of environmentally friendly adsorbents. According to the Hauser ratio and porosity analysis, the corncob has a good flow ability of the adsorbent material and many pores, which is very advantageous for MB adsorption. As a result of the experiment, MB concentration of less than 0.005 g/L was very efficiently removed with 10 g/L of bioadsorbent corncob and the maximum adsorption capacity of corncob for MB dyes was obtained at 417.1 mg/g. In addition, adsorption process of MB onto corncob was a physical process according to adsorption energy analysis. Corncob can efficiently and environmentally remove MB in aqueous solution, and is very cost effective and can recycle the abandoned resources.

• Journal of Environmental Science International
• /
• v.15 no.6
• /
• pp.579-586
• /
• 2006

The purposes of this paper were to monitor the temperature rising courses and spark discharge of the modified granular activated carbon (GAC) by microwave (MW) irradiation and to evaluate absorption of benzene. The GAC coated on $SiO_2$, boron, talc, ferrite was named as the modified GAC. Thermal and spark discharge measurement of virgin GAC and modifed GAC has been carried out using a MW device operating at 2450 MHz under various energy conditions. The results of this paper as follows. First, the modified GAC is more efficient than the virgin GAC in temperature control. Temperature gradient of the modified GAC is more lower than that of virgin GAC. The temperature gradient of GAC was observed in the following order : virgin GAC, Mn-Zn ferrite/GAC, Ni-Zn ferrite,/GAC, $SiO_2/GAC$, Boron/GAC, Talc/GAC. Second, the spark discharge of the modified GAC was diminished, compared with that of virgin GAC. Because of its excellent electrical insulating properties, the coating material prevents the spark discharge. Finally, the benzene adsorption capacity of the modified GAC decreased due to diminishing of adsorption site by the coating material. Considering the temperature gradient and spark discharge of GAC, the GAC coated $SiO_2$ would be appropriate absorbent under irradiation of MW.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11a
• /
• pp.313-317
• /
• 2010

Li, Zr doped mesoporous silica was synthesized in one pot and investigated for low temperature $CO_2$ adsorption. Herein CTAB and TEOS are used as structural directing agent and silica source respectively. The characteristics of the material was obtained from FT IR, XRD, SEM, TG and BET results. ICP AES results revealed the presence of lithium and zirconium. The material possesses high surface area ($962.22m^2g^{-1}$) with mono dispersed particles of about 2 nm. The maximum $CO_2$ adsorption capacity is 5 wt % (50 mg/g) of $CO_2$/g of sorbent at $25^{\circ}C$, which is regenerable at $200^{\circ}C$. This regeneration temperature of the adsorbent is lower than the reported lithium zirconium silicate powder. Until now, there is no report for the synthesis of Li, Zr doped mesoporous silica. The performance studies illustrate that Li, Zr doped mesoporous silica is tunable, regenerable, recyclable and selective sorbent and hence found to be a promising candidate for $CO_2$ adsorption.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.160.1-160.1
• /
• 2014

Using a density functional theory calculation including van der Waals (vdW) corrections, we report that $H_2$ adsorption in a cubic-crystalline microporous metal-organic framework (MOF-5) leads to volume shrinkage, which is in contrast to the intuition that gas adsorption in a confined system (e.g., pores in a material) increases the internal pressure and then leads to volumetric expansion. This extraordinary phenomenon is closely related to the vdW interactions between MOF and $H_2$ along with the $H_2$-$H_2$ interaction, rather than the Madelung-type electrostatic interaction. At low temperatures, $H_2$ molecules adsorbed in the MOF-5 form highly symmetrical interlinked nanocages that change from a cube-like shape to a sphere-like shape with $H_2$ loading, helping to exert centrosymmetric forces and hydrostatic (volumetric) stresses from the collection of dispersive interactions. The generated internal negative stress is sufficient to overcome the stiffness of the MOF-5 which is a soft material with a low bulk modulus (15.54 GPa).

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.368-372
• /
• 2009

A technique to measure the adsorption characteristic of surface area and pore size distribution is proposed and its performance is examined. While the existing equipment utilizes liquid nitrogen, the proposed uses carbon dioxide at the room temperature leading to the small measuring device with easy operation and short measurement time. The performance of the device has been examined with micro-particle carbon cryogel and bamboo activated carbon. The results from the proposed device compared with those of the adsorption apparatus indicate that the measurement of meso-porous material is comparable but micro-porous material gives some error.

• Journal of Environmental Science International
• /
• v.22 no.7
• /
• pp.837-845
• /
• 2013

This study was designed to synthesize mesoporous carbon, porous carbonic material and to characterize its surface in an attempt to adsorption methane gas($CH_4$). Synthesis of mesoporous carbon was carried out under two steps ; 1. forming a RF-silica complex with a mold using CTMABr, a surfactant, and TEOS, raw material of silica, and 2. eliminating silica through carbonization and HF treatment. The mesoporous carbon was synthesized under various conditions of synthesis time and calcination. Eight different types of mesoporous carbon, which were designated as MC1, MC2, MC3, MC4, MCT1, MCT2, MCT3, and MCT4, were prepared depending upon preparation conditions. The analysis of mesoporous carbon characteristics showed that the calcination of silica stabilized the mixed structure of silica and carbonic complex, and made the particle uniform. The results also showed that hydrothermal synthesis time did not have a strong influence on the size of pore. The bigger specific surface area was obtained as the hydrothermal synthesis time was extended. However, the specific surface area was getting smaller again after a certain period of time. In adsorption experiments, $CH_4$ was used as adsorbate. For the case of $CH_4$, MCT3 showed the highest adsorption efficiency.

• Environmental Engineering Research
• /
• v.24 no.1
• /
• pp.173-179
• /
• 2019

Prussian blue (PB) is known to be an effective material for radioactive cesium adsorption, but its nano-range size make it difficult to be applied for contaminated water remediation. In this study, a simple and versatile approach to immobilize PB in the supporting matrix via surface functionalization was investigated. The commercially available poly vinyl alcohol (PVA) sponge was functionalized by acrylic acid (AA) to change its major functional group from hydroxyl to carboxylic, which provides a stronger ionic bond with PB. The amount of AA added was optimized by evaluating the weight change rate and iron(III) ion adsorption test. The FTIR results revealed the surface functional group changing to a carboxyl group. The surface functionalization enhanced the attachment of PB, which minimized the leaching out of PB. The $Cs^+$ adsorption capacity significantly increased due to surface functionalization from 1.762 to 5.675 mg/g. These findings showed the excellent potential of the PB-PAA-PVA sponge as a cesium adsorbent as well as a versatile approach for various supporting materials containing the hydroxyl functional group.

• Korean Journal of Materials Research
• /
• v.33 no.4
• /
• pp.151-158
• /
• 2023

In this study, a new type of composite material combined with carbonyl iron, a relatively strong ferromagnetic material, was prepared to overcome the current application limitations of Prussian blue, which is effective in removing radioactive cesium. The surface of the prepared composite was analyzed using SEM and XRD, and it was confirmed that nano-sized Prussian Blue was synthesized on the particle surface. In order to evaluate the cesium removal ability, 0.2 g of the composite prepared for raw cesium aquatic solution at a concentration of 5 ㎍ was added and reacted, resulting in a cesium removal rate of 99.5 %. The complex follows Langmuir's adsorption model and has a maximum adsorption amount (q_e) of 79.3 mg/g. The Central Composite Design (CCD) of the Response Surface Method (RSM) was used to derive the optimal application conditions of the prepared composite. The optimal application conditions achieved using Response optimization appeared at a stirring speed of pH 7, 17.6 RPM. The composite manufactured through this research is a material that overcomes the Prussian Blue limit in powder form and is considered to be excellent economically and environmentally when applied to a cesium removal site.

• Resources Recycling
• /
• v.17 no.1
• /
• pp.59-65
• /
• 2008

The adsorption features of nickel ion in wastewater on manganese dioxide from spent batteries were investigated for its usage as an adsorbent. The aquatic behavior of nickel ion was characterized by MINTEQ program and the considered influential variables on the adsorption of nickel ion were its initial concentration, reaction temperature, the amount of adsorbent, and pH. The adsorption ratio of nickel ion decreased with increasing its initial concentration and thermodynamic estimation has been carried out based on the adsorption characteristics of nickel ion depending on temperature. In addition, the adsorption of nickel ion was shown to be promoted according to the amount of manganese dioxide and a lot of nickel ions were adsorbed as the solution pH was raised.