• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.697-700
• /
• 2006

The unique technology was developed to control the hydration heat of mass concrete by adding the Phase Change Material(PCM) to concrete. The PCM was designed to liquefy at 60 degrees and its size was limited under $10{\sim}30$ micro meters to be put in pores and to have no effect on compressive strength. In the hydration heat test, center temperature of the PCM specimen was reduced by 10 degrees without any difference in the strength. Even in the adiabatic temperature rise test, the final adiabatic temperature rise amount was reduced as much as 25% in comparison with the standard value in Korean Concrete Standard Specification.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.4
• /
• pp.84-91
• /
• 2014

In this study, in order to find the improvement effect of metakaolin for using improvement of strength in concrete structures, it is investigated the diffusion coefficient of chloride ions and adiabatic temperature rise test. As a result, due to the mixing of metakaolin, it has been confirmed reducing diffusion coefficient of chloride ions and could prevent down of slump for use of adding fly ash. Therefore, ensuring resistance to chloride ion penetration into concrete, it is possible to enlarge the W/B ratio and reduce the adiabatic temperature rise by mixing of metakaolin. So, it is confirmed that the durability of concrete structures is increased.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.114-115
• /
• 2021

The research team conducted a series of studies to use CGS as fine aggregate for concrete. In this paper, through the adiabatic temperature rising test, CGS' hydration heating performance and its usability as a mass concrete hydration heating agent were reviewed. According to the analysis, the maximum temperature of the mix of OPC 100 was 53.7℃, and the temperature of CGS 50% was 45.2℃, which was 8.5℃ lower than the OPC 100.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.1
• /
• pp.37-45
• /
• 2009

In this study, experiments of development and application of 50 MPa high-performance concrete are performed for large dimensional tunnel linings. In order to produce 50MPa high-performance concrete, eight optimal mixtures replacing with fly ash and ground granulated blast furnace slag up to 50 percent of type I Portland cement were selected then tests for mechanical properties and simple adiabatic temperature rise tests were carried out. And in order to assess the quantitative characteristics of heat of hydrations of developed mixtures, three mixtures that the type I Portland cement (OPC) and each one mixture of binary and ternary mixtures (BS30, F15S35) were reselected, then the adiabatic temperature rise tests and mock-up tests were performed. Consequently, the comparisons between the results of mock-up tests and finite element analysis can be enhanced the reliability of analyzing routines of thermal behaviours of the developed high-performance concrete.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.36-37
• /
• 2019

In domestic construction industry progress, construction and quality control of large structures are considered to be important as the superstructure and mass scale of structures. In the case of mass concrete, high hydration heat caused by cement hydration generates temperature stress by generating internal temperature difference with the concrete surface. These temperature stresses cause cracks to penetrate the concrete structure. A method of lowering the heat generation by incorporating Urea in order to reduce the concrete temperature crack has been proposed. In this study, the heat function coefficient for the FEM temperature crack analysis of the mass concrete containing the element was derived and the adiabatic temperature rise test was carried out according to the incorporation of the element. As a result of this experiment, the maximum temperature of 41 ± 1℃ was obtained irrespective of the amount of urea, and the maximum temperature decreased by 16.9℃ in concrete containing 40kg/㎥ of urea.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.235-236
• /
• 2021

This study evaluated temperature distribution through adiabatic temperature rising test and hydration heat Analysis as a performance verification to utilize CGS as a hydration heat reduction material for mass concrete when replacing it with fine aggregate. According to the analysis, the temperature difference between the center and the surface was the highest at about 30℃, followed by the CGS 50% at 26℃ and the low heat combiner FA 30% at 23℃.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05b
• /
• pp.345-348
• /
• 2005

This paper presents the result of adiabetic temperature rise and fundamental properties of concrete combining admixtures. According to results, difference of setting time with I5.5hours is observed between S-P and R-F30 mixture. Based on the adiabetic temperature rise test, 8$^{circ}C$of heat producted occurs between E-P and R-F30 mixture. is applied to estimate the temperature rising under adiabetic curing condition, which exhibits closer consistency with tested value. The function mentioned above can account for the effect of dormant period in hydration process at early stage on hydration heat production. It reveals that the consideration of placing layer based on the mixture adjustment(E-P mixture at top layer and R-F30 mixture at bottom layer) in mass concreting will contribute to reduce hydration heat as well as alleviate tensile stress discrepancy between placing layer.

• Journal of the Korea Concrete Institute
• /
• v.22 no.3
• /
• pp.389-397
• /
• 2010

Concrete has excellent mechanical properties, high durability, and economical advantages over other construction materials. Nevertheless, it is not an easy task to apply concrete to long span bridges. That's because concrete has a low strength to weight ratio. Ultra high performance concrete (UHPC) has a very high strength and hence it allows use of relatively small section for the same design load. Thus UHPC is a promising material to be utilized in the construction of long span bridges. However, there is a possibility of crack generation during the curing process due to the high binder ratio of UHPC and a consequent large amount of hydration heat. In this study, adiabatic temperature rise and mechanical properties were modeled for the stress analysis due to hydration heat. Adiabatic temperature rise curve of UHPC was modeled superposing 2-parameter model and S-shaped function, and the Arrhenius constant was determined using the concept of equivalent time. The results are verified by the mock-up test measuring the temperature development due to the hydration of UHPC. In addition, models for mechanical properties such as elastic modulus, tensile strength and compressive strength were developed based on the test results from conventional load test and ultrasonic pulse velocity measurement.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.940-945
• /
• 1998

Recently, serious cracking problems have been reported in this country while the process of actual massive concrete construction. he hydration heat arising from the chemical reaction of cement with water causes temperature differentials in between inside and outside of a structural member, and these temperature differentials induce thermal stresses. In this paper, we described on the practical application and quality control of the mass concrete mixed with fly-ash. This project is investigating adiabatic temperature rise test of concrete, mock-up test in the laboratory, ad B/P before placing the mass concrete in site. As a result, we can be prevent temperature cracking from the cement hydration heat of mass concrete and also can be showed up secure quality control flow chart of mass concrete.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.3
• /
• pp.103-107
• /
• 2009

It is necessary to develop a new technology for effectively controlling thermal crack caused hydration heat according to the increasing construction of large size massive concrete structures such as mat foundation of high-rise building. Therefore, to develop a new technology for reducing hydration heat of large size massive concrete in this study, it was investigated hydration heat generation properties of binder using latent heat materials. As a test result, it was confirmed that latent heat materials were advanced on the reduction of hydration heat and control of thermal crack. It is expected to be applied as the excellent technology on the management of hydration heat and thermal crack in large size massive concrete structures.