• The Journal of Advanced Prosthodontics
• /
• 제16권1호
• /
• pp.48-56
• /
• 2024

PURPOSE. To evaluate the metameric disparities among monolithic zirconia materials with differing yttrium compositions across various lighting conditions. MATERIALS AND METHODS. Thirty-six square-shaped zirconia samples measuring 10 × 10 × 0.5 mm were prepared from monolithic zirconia materials with three different yttrium contents. A 0.2 mm thick layer of polymerized dual-polymerizable self-adhesive resin cement was created using a silicone mold with the same dimensions as the prepared zirconia specimens. To evaluate metamerism, color measurements were conducted using a spectrophotometer device on a neutral gray background in a color measurement cabinet that offers four different illumination environments. All samples underwent aging by subjecting them to 10000 thermal cycles using a thermal cycle tester. Following thermal aging, color measurements were taken once more, and the data were recorded using the CIE L^*, a^*, b^* color system. Two-way ANOVA and Post-hoc Bonferroni tests were employed to analyze the data. RESULTS. It was observed that there was no statistical difference among the color measurements made in different illumination environments of the monolithic zirconia ceramics used to evaluate metamerism (P > .05). This observation remained consistent both before and after thermal aging. After thermal aging, the color of monolithic zirconia materials exhibited a tendency towards red and yellow hues, accompanied by a decrease in brightness levels. CONCLUSION. It can be stated that different illumination conditions did not affect the metamerism of monolithic zirconia materials, but there was a color change in monolithic zirconia materials after a thermal aging period equivalent to one year.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.285-293
• /
• 2016

The high velocity oxygen fuel(HVOF) thermal spray is a kind of surface modification techniques to produce the sprayed coating layer. This process is to form the coating layer after spraying the powder to molten or semi-molten state by the ultra-high speed at the high-temperature heat source and conflicting with a substrate. The efficiency of thermal spraying is dropped, however, because the semi-molten powder in a spray process become a factor that degrades the mechanical property by the formed pore within the coating layer. Therefore, it is necessary to melt completely the thermal spray powder in order to produce the coating layer with an optimal adhesive force. In this study, to improve the wear resistance, corrosion resistance and heat resistance, the plungers of high-speed and ultra-high pressure reciprocating hydraulic pumps used in ironworks are manufactured with STS $420J_2$ and are coated by the powders of WC-Co-Cr and WC-Cr-Ni including the WC of high hardness using a HVOF thermal sprayer developed in this laboratory. These are called by the surface-modified plungers. The surface roughness, hardness, and surface and cross-sectional microstructure of these two surface-modified and conventional ceramic plungers are measured and compared before operation with after operation for 100 days. It is found that the values of centerline average surface roughness and maximum height for conventional ceramic plunger are 9.5 to 10.8 and 5.2 to 5.7 times higher than those of surface-modified ones coated by WC-Co-Cr and WC-Cr-Ni because the fine tops and bottoms on surface roughness curve of conventional ceramic plunger are approximately 100 times higher than those of surface-modified ones. In addition, the pores and scratches in the surface microstructure are considerably formed in the order of conventional ceramic, WC-Cr-Ni and WC-Co-Cr surface-modified plungers. The greater the WC content of high hardness powder is less the change in the plunger surface.

• Composites Research
• /
• 제32권1호
• /
• pp.65-70
• /
• 2019

항공기 복합재료 날개 구조는 대부분 접착 혹은 패스너로 체결되어 있는데, 이러한 적층 구조 복합재료는 층간 강도가 취약하여 층간 분리가 일어나기 쉽다. 이러한 적층 복합재료의 단점을 보완하기 위해 두께 방향의 섬유를 보강한 3차원 직조형 복합재료를 통하여 강도, 손상 내구성, 충격 및 피로 하중을 향상시킬 수 있다. 또한, 자동화된 직조 공정에 의하여 단일 구조 near-net-shape의 프리폼 제조가 가능하기 때문에 공정 단축, 체결 부품 감소로 복합재료 전체 가격을 절감할 수 있다. 따라서 본 연구에서는 3차원 직조형 복합재료의 항공기 구조물 적용 가능성을 확인하기 위하여 3차원 프리폼의 기본적인 구조인 orthogonal(ORT), layer-to-layer(LTL), through-the-thickness(TTT) 패턴을 직조하고 이를 복합재료로 성형하여 압축 시험, 인장 시험, Open-hole 인장 시험을 하였다. 이 중 orthogonal 직조 복합재료가 인장 및 압축 탄성계수와 강도 모두 가장 높았으며 노치 민감도에서도 orthogonal 복합재료가 일방향 적층복합재료나 패브릭 적층 복합재료에 비하여 가장 우수한 특성을 보였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.311-311
• /
• 2009

Carbon nanotubes (CNTs) belong to an ideal material for field emitters because of their superior electrical, mechanical, and chemical properties together with unique geometric features. Several applications of CNTs to field emitters have been demonstrated in electron emission devices such as field emission display (FED), backlight unit (BLU), X-ray source, etc. In this study, we fabricated a CNT cathode by using filtration processes. First, an aqueous CNT solution was prepared by ultrasonically dispersing purified single-walled CNTs (SWCNTs) in deionized water with sodium dodecyl sulfate (SDS). The aqueous CNT solution in a milliliter or even several tens of micro-litters was filtered by an alumina membrane through the vacuum filtration, and an ultra-thin CNT film was formed onto the alumina membrane. Thereafter, the alumina membrane was solvated by acetone, and the floating CNT film was easily transferred to indium-tin-oxide (ITO) glass substrate in an area defined as 1 cm with a film mask. The CNT film was subjected to an activation process with an adhesive roller, erecting the CNTs up to serve as electron emitters. In order to measure their luminance characteristics, an ITO-coated glass substrate having phosphor was employed as an anode plate. Our field emitter array (FEA) was fairly transparent unlike conventional FEAs, which enabled light to emit not only through the anode frontside but also through the cathode backside, where luminace on the cathode backside was higher than that on the anode frontside. Futhermore, we added a reflecting metal layer to cathode or anode side to enhance the luminance of light passing through the other side. In one case, the metal layer was formed onto the bottom face of the cathode substrate and reflected the light back so that light passed only through the anode substrate. In the other case, the reflecting layer coated on the anode substrate made all light go only through the cathode substrate. Among the two cases, the latter showed higher luminance than the former. This study will discuss the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the either side.

• 한국도로학회논문집
• /
• 제11권2호
• /
• pp.121-132
• /
• 2009

본 연구에서는 노후 콘크리트 포장의 효율적 유지보수를 위하여 국내 최초 적용된 Thin Bonded Continuously Reinforced Concrete Overlay (CRCO) 공법의 초기 공용성이 평가되었다. 서해안 고속도로의 표층 파손 구간에 Jointed Plain Concrete Pavement (JPCP) 덧씌우기와 CR8O 공법을 이용한 보수가 진행되었다. JPCP 덧씌우기 공법이 적용된 구간에서는 인접 슬래브가 완전히 분리되도록 덧씌워진 층의 줄눈을 완전히 커팅하였으며, CRCO 공법이 적용된 구간에서는 0.5% 종방향 철근과 위치 고정용 횡방향 철근을 설치한 후 그 위에 덧씌우기를 수행하였다. 두 구간 모두에서 3종시멘트가 이용되었다. 현장 강도 시험 결과, 1$\sim$3일 내에 교통개방이 가능한강도가 발현된 것이 확인되었으며, vibrating wire gauge (VWG) 데이터 분석 결과 CRCO 공법이 기존 포장의 줄눈 거동을 억제하는 것으로 나타났다. 부착강도 시험결과, 재령에 상관없이 높은 부착강도가 확인되었다. 한편 JPCP 덧씌우기 공법이 적용된 구간에서는 중앙부에서, CRCO 공법이 적용된 구간에서는 CRCO 포장과 같은 무작위 횡방향 균열이 관찰되었으며, CRCO 공법의 균열폭 거동이 JCP 보다 50% 정도 낮은 것으로 나타났다.

• Corrosion Science and Technology
• /
• 제7권1호
• /
• pp.50-60
• /
• 2008

The majority of the described experimental results deal with relatively pure aluminium. Variations were made in the pretreatment of the aluminum substrates and an investigation was performed on the resulting changes in oxide layer composition and chemistry. Subsequently, the bonding behavior of the surfaces was investigated by using model adhesion molecules. These molecules were chosen to represent the bonding functionality of an organic polymer. They were applied onto the pretreated surfaces as a monolayer and the bonding behavior was studied using infrared reflection absorption spectroscopy. A direct and clear relation was found between the hydroxyl fraction on the oxide surfaces and the amount of molecules that subsequently bonded to the surface. Moreover, it was found that most bonds between the oxide surface and organic functional groups are not stable in the presence of water. The best performance was obtained using molecules, which are capable of chemisorption with the oxide surface. Finally, it was found that freshly prepared relatively pure aluminum substrates, which are left in air, rapidly lose their bonding capacity towards organic functional groups. This can be attributed to the adsorption of contamination and water to the oxide surface. In addition the adhesion of a typical epoxy-coated aluminum system was investigated during exposure to water at different temperatures. The coating was found to quite rapidly lose its adhesion upon exposure to water. This rapid loss of adhesion corresponds well with the data where it was demonstrated that the studied epoxy coating only bonds through physisorptive hydrogen bonding, these bonds not being stable in the presence of water. After the initial loss the adhesion of the coating was however found to recover again and even exceeded the adhesion prior to exposure. The improvement could be ascribed to the growth of a thin oxyhydroxide layer on the aluminum substrate, which forms a new, water-stable and stronger bond with the epoxy coating. Two routes for improvement of adhesion are finally decribed including an interphasial polymeric thin layer and a treatment in boiling water of the substrate before coating takes place. The adhesion properties were finely also studied as a function of the Mg content of the alloys. It was shown that an enrichment of Mg in the oxide could take place when Mg containing alloys are heat-treated. It is expected that for these alloys the (hydr)oxide fraction also depends on the pre-treatment and on the distribution of magnesium as compared to the aluminium hydroxides, with a direct impact on adhesive properties.

• Journal of the Korean Wood Science and Technology
• /
• 제27권3호
• /
• pp.39-50
• /
• 1999

라디에타소나무, 케루잉, 딜레니아, 터미날리아 및 칼로필롬 단판에 내화약제로서 20% 제2인산암모늄 수용액을 상압 침지 및 진공가압침지 처리한 시험을 실시 하였으며, 라디에타소나무와 케루잉 단판의 구성형태와 내화약제의 침지처리 조건들을 여러형태로 조합한 합판을 요소 멜라민 수지와 페놀수지 접착제를 사용하여 제조하였다. 결과, 라디에타소나무가 케루잉보다 약제보유도 및 처리효과가 뛰어났으며, 진공가압침지가 상압침지보다 약제보유면에서는 유효하였다. 그리고, 기계적 성질에 있어 단판첨지법으로 내화처리를 하여 제조한 합판이 반드시 접착력 및 휨강도적 성질의 저하를 가져오지는 않았으며, 내화성에 있어서는 요소 멜라민수지 접착이 우수한 성능을 보였다. 결과적으로, 접착 강도성능과 내화성능을 고려한 단판 수종의 적정한 선택, 층간구성(조합) 및 교호약제처리가 실제 사용시 가능할 것이다.

• 한국산학기술학회논문지
• /
• 제11권5호
• /
• pp.1741-1746
• /
• 2010

본 연구는 건축자재로 널리 사용되는 PVC 바닥상재 표면을 오염성 및 정전기로부터 보호하기 위하여 기존에 사용하는 광경화형 우레탄-아크릴 수지에 내오염/대전성을 향상시킨 광경화형 내오염 코팅액 개발에 관한 것이다. PVC 바닥상재용으로 사용되는 내오염성이 없는 우레탄-아크릴 수지에 4가 암모늄을 사용한 수용성 대전방지제와 아크릴용 대전방지제, 폴리우리탄용 대전방지제를 수지의 양 대비 함량(wt%) 5~20%로 변화하여 첨가한 후 배합하여 수지의 내오염/대전성을 향상시킨 내오염 코팅액을 제조하였다. 제조한 내오염 코팅액은 코팅 층의 두께조절이 가능한 코팅(Bar-coating)을 사용하여 PVC 바닥상재에 코팅 한 후 내오염성, 대전성, 부착력, 코팅두께 등의 코팅 층 표면물성을 평가하였다. 연구결과, 수지에 수용성대전방지제 15%를 혼합하여 제조한 코팅액을 Bar-coater No.12로 코팅한 코팅표면이 전기저항($3.24{\times}10^9{\Omega}/cm^2$), 내오염도(매직 Test, 먼지부착 Test) 및 부착력(100%) 모두 가장 좋은 물성을 보였다. 전반적으로 함량이 많을수록 전기저항과 오염도에서 우수한 것으로 나타났다. 그러나 대전방지제가 과량으로 들어간 경우 migration 현상이 보이는 것을 알 수 있었다.

• Restorative Dentistry and Endodontics
• /
• 제22권1호
• /
• pp.228-243
• /
• 1997

The changes of microstructures, morphology of sclerotic dentin and bonding aspects generated by an adhesive resin was investigated. Incisors and premolars showing natural cervical abrasions were collected and conditioned with 10 % phosphoric acid or 10 % maleic acid. The sclerotic dentin specimens were then rinsed and blot-dried and applied with dentin adhesive (All Bond 2) to the conditioned dentin surface. To examine the morphologic change of the sclerotic dentin specimen after etching and bonding procedure, the treated specimens were examined by SEM. To analyze the chemical composition of sclerotic dentin and crystals occluding dentinal tubules, the sclerotic dentin specimen was powdered and examined with X-ray Diffractometer. To investigate the Ca/P weight percent ratio within the dentinal tubules, the sclerotic dentin specimen was fractured perpendicularly to the long axis of the tooth from the center of cervical abrasion lesion and then examined with EDX(Energy Dispersive X-ray) microanalyzer. The results were as follows : 1. The increased width of peritubular dentin and the depositions of the irregular amorphous materials within the dentinal tubules were showed in the sclerotic dentin specimens. 2. After the treatment of sclerotic dentin specimen with 10 % phosphoric acid or 10 % maleic acid, the lateral side of tubules rather than cross-sectional tubule openings was showed exclusively at the incisal and gingival incline of the specimens. 3. After the treatment of sclerotic dentin specimen with 10 % phosphoric acid or 10 % maleic acid, the hybrid layer was not formed evidently and the resin tag was not formed or shortly penetrated into the tubules with the thinner diameter. 4. According to the results of XRD analysis of the sclerotic dentin specimen, Hydroxyapatite and Octacalcium phosphate were predominent, however, Whitlockite crystals were rare. 5. The mean Ca/P weight percent ratio analysed from 5 fractured sclerotic dentin specimens was $2.322{\pm}0.170$ at the intertubular dentin, $1.826{\pm}0.051$ within the dentinal tubule.

• Restorative Dentistry and Endodontics
• /
• 제31권6호
• /
• pp.415-426
• /
• 2006

자가부식 상아질 접착제의 중합 후 시간 경과에 따른 접착강도의 변화를 관찰하고, 중합률의 영향을 평가하고자 하였다. 36개의 상하악 대구치를 Single Bond (SB, 3M ESPE, USA), Clearfil SE Bond (SE, Kuraray, Japan), Xeno-III (XIII, Dentsply, Germany), 및 Adper Prompt (AP, 3M ESPE, USA)를 적용하는 4군으로 나누고, 이를 다시 미세인장접착강도 측정 시점에 따라 22$^{\circ}$C의 증류수에 보관 후 48시간에 측정한 군과 7일 후 측정한 군, 및 접착된 시편을 5000회 열순환을 시행하고 측정한 군으로 나누었다. 모래시계 형태의 접착시편을 제작하여 만능시험기 (Model 4466; Instron Co., USA)로 1 mm/min의 하중속도 하에서 미세인장접착강도를 측정하였다. 접착제의 중합률은 Fourier 변환 적외선 분광법을 이용하여 중합 직후, 48시간, 1주일에 측정하였으며, 주사전자현미경을 이용하여 파절 단면을 관찰하였다. 미세인장접착강도와 중합률 모두 시간의 경과에 따라 유의한 증가를 보였으며, 시간 경과와 재료간에 교호작용이 있었다 (미세인장접착강도, 2-way ANOVA, p = 0.018; 중합률, Repeated Measures ANOVA, p < 0.001) . XIII와 AP의 낮은 미세인장접착강도는 낮은 중합률 때문임을 확인할 수 있었다. 48시간 이후에 SE와 AP에서 접착강도가 증가 되는 것은 중합률과는 관련이 없고, 전자현미경에서 관찰되는 접착제층의 성숙에 따른 취성의 증가가 원인일 가능성이 제기된다.