• 마이크로전자및패키징학회지
• /
• 제10권3호
• /
• pp.9-17
• /
• 2003

In this paper, thermo-mechanical and rheological properties of NCPs (Non-Conductive Pastes) depending on silica filler contents and diluent contents were investigated. And then, thermal cycling (T/C) reliability of flip chip assembly using selected NCPs was verified. As the silica filler content increased, thermo-mechanical properties of NCPs were changed. The higher the silica filler content was added, glass transition temperature ($T_g$) and storage modulus at room temperature became higher. While, coefficient of thermal expansion (CTE) decreased. On the other hand, rheological properties of NCPs were significantly affected by diluent content. As the diluent content increased, viscosity of NCP decreased and thixotropic index increased. However, the addition of diluent deteriorated thermo-mechanical properties such as modulus, CTE, and $T_g$. Based on these results, three candidates of NCPs with various silica filler and diluent contents were selected as adhesives for reliability test of flip chip assemblies. T/C reliability test was performed by measuring changes of NCP bump connection resistance. Results showed that flip chip assembly using NCP with lower CTE and higher modulus exhibited better T/C reliability behavior because of reduced shear strain in NCP adhesive layer.

• 대한전자공학회논문지SD
• /
• 제45권2호
• /
• pp.13-20
• /
• 2008

본 논문에서는 CMOS 이미지 센서의 웨이퍼 레벨 어셈블리를 위한 스페이스 제작 방법을 설명하였다. 스페이스 제작을 위해서 SU-8, PDMS, Si-interposer를 이용하는 세 가지 방법을 제안하였다. SU-8 스페이스에서는 균일한 두께 특성을 위해서 웨이퍼 회전 장치를 고안했으며, PDMS 스페이스에서는 glass/PDMS/glass 구조의 정렬 접합을 위해서 새로운 접합 방법을 제안하였다. Si-interposer를 이용한 스페이스 제작에서는 DRF을 이용한 접합 조건을 확립하였다. 세 가지의 실험 결과 Si-interposer를 이용한 스페이스 제작 시 glass/스페이스/glass 구조의 접합력이 가장 뛰어났으며, 접합력의 크기는 32.3MPa의 전단응력을 나타내었다.

• Journal of Electrical Engineering and Technology
• /
• 제8권3호
• /
• pp.603-609
• /
• 2013

In this paper, we describe the analysis of inkjet-printed silver (Ag) patterns on epoxy-coated substrates according to several reliability evaluation test method guidelines for conventional printed circuit boards (PCB). To prepare patterns for the reliability analysis, various regular test patterns were created by Ag inkjet printing on flame retardant 4 (FR4) and polyimide (PI) substrates coated with epoxy for each test method. We coated the substrates with an epoxy primer layer to control the surface energy during printing of the patterns. The contact angle of the ink to the coated epoxy primer was $69^{\circ}$, and its surface energy was 18.6 $mJ/m^2$. Also, the substrate temperature was set at $70^{\circ}C$. We were able to obtain continuous line patterns by inkjet printing with a droplet spacing of $60{\mu}m$. The reliability evaluation tests included the dielectric withstanding voltage, adhesive strength, thermal shock, pressure cooker, bending, uniformity of line-width and spacing, and high-frequency transmission loss tests.

• 한국표면공학회지
• /
• 제44권6호
• /
• pp.269-276
• /
• 2011

Phase evolution and tribological behavior of Cr-Mo-N multi compositional films with different interlayer were investigated. The films were deposited by hybrid PVD (Physical Vapor Deposition) system consisted of dc unbalanced magnetron (UBM) sputtering and arc ion plating (AIP) sources. A pure molybdenum (Mo) was used as sputtering target and also a pure Cr was used as AIP target to form the Cr-Mo-N films. Various growth planes were found, no textured surface, in all of the multi composition films. Maximum value of microhardness was measured in Cr-Mo-N film with Mo interlayer as 29 GPa. Composition film was mainly showed the aspect of the adhesive wear than CrN film. The friction coefficient was decreased from 0.6 for pure CrN coating to 0.35 for Cr-Mo-N film with Mo interlayer. This result may come from the formation of metal oxide tribo-layer which is known as solid lubricant during the wear test.

• Tribology and Lubricants
• /
• 제4권1호
• /
• pp.56-68
• /
• 1988

The wear resistance of P-bronze which is widely used as worm gear material was investigated. In order 1o study the effect of additional elements on the wear resistance of Pbronze, the applied load and sliding time were selected as variables, and SCM4, were used as against metal. The addition of Fe improve wear resistance, for it precipities hard Fe$_3$ P phase and the work hardening coefficients are lowered due to decreasing solubility of P. When Fe is added in conventional P-bronze, the alloy is rather sliding than forming wear debris by frictional force during wear test. Experimental results indicated that the wear mechanisms for P-bronze are mainly consisted of abrasive wear due to Beilby layer forming mechanism and adhesive wear due to thermally activated wear mechanism. Moreover, the weight loss is decreased in accordance with increasing load and time. However the rate of wear loss is decreased as the sliding time is increased.

• 한국철도학회논문집
• /
• 제12권4호
• /
• pp.481-487
• /
• 2009

포장궤도에서는 프리팩 콘크리트방식으로 도상자갈을 충전층의 골재로 활용한다. 골재의 조건은 강도가 확보되어야 하고, 주입성 확보를 위한 입도가 확보되어야 하며, 모르터의 부착강도를 높이기 위하여 골재 표면의 불순물이 제거되어야 한다. 골재의 원활한 공급 측면에서 기존 도상자갈을 재활용하는 것이 유리하며 재활용성을 높이기 위하여 기존의 철도도상규격을 크게 벗어나지 않는 기준을 적용하는 것이 필요하다. 따라서 본 연구에서는 포장궤도에서의 도상자갈 재활용성을 확보 할 수 있는 판단 기준을 마련하기 위하여 재활용 도상자갈의 재료 및 물리적 특성, 입도별 지지력 특성, 충전성, 강도특성 등을 검토하였으며, 그 결과를 바탕으로 골재 사용기준을 제안하고자 하였다.

• 대한전자공학회논문지SD
• /
• 제40권7호
• /
• pp.481-485
• /
• 2003

25㎛ 두께의 폴리이미드 박핀 기판을 glass 기판에 부착하여 최대 온도 150℃에서 비정질 실리콘 TFT를 제작하였다. 본 논문은 plastic 기판 위에 TFT가 제작되는 공정 절차를 요약하고 glass 위에 제작된 TFT와 ON/OFF 전달특성과 전계효과 이동도를 서로 비교해 보았다. a-SiN:H 코팅층은 plastic 기판의 표면 거칠기를 감소시키는 중요한 역할을 하여 TFT의 누설전류를 감소시키고 전계효과 이동도를 증가시켰다. 따라서 a-SiN:H 코팅층을 이용하여 plastic 기판에 양철의 TFT를 제작하였다.

• Journal of Welding and Joining
• /
• 제35권3호
• /
• pp.15-20
• /
• 2017

In this paper, two types of assemblies using CNT-filled SACAs (with 0.03 wt% CNTs and without CNT) were prepared to investigate the influence of carbon nanotubes (CNTs) on the reliability properties of solderable anisotropic conductive adhesives (SACAs) with a low-melting-point alloy (LMPA). Two types of reliability test including thermal shock (TS: -55 to $125^{\circ}C$, 1000 cycles) and high-temperature and high-humidity (HTHH: $85^{\circ}C$, 85% RH, 1000 h) tests were conducted. The SACA assemblies with and without CNTs showed stable electrical reliability properties due to the formation of wide and stable metallurgical interconnection between corresponding metallizations by the molten LMPA fillers. Although the mechanical pull strength of CNT-filled SACA assemblies was decreased after thermal aging (because of the excessive layer growth and planarization of the IMCs), the CNT-filled SACA with 0.03wt% CNTs showed enhanced mechanical reliability properties compared with the SACA assemblies no CNTs. This enhancement in mechanical performance was due to the reinforcement effect of the CNTs. These results demonstrate that CNTs within the CNT-filled SACAs can improve the reliability properties of CNT-filled SACAs joints due to their superior physical properties.

• Fibers and Polymers
• /
• 제3권4호
• /
• pp.153-158
• /
• 2002

A series of waterborne polyurethanes (WBPU) were prepared from 4,4-dicyclohexylmethane diisocyanate ($H_{12}$MDI),2,2-bis(hydroxylmethyl) propionic acid (DMPA), othylenediarnine (EDA), triethylamine (TEA), and triblock glycol [TBG, ($\varepsilon$-caprolactone)$_{4.5}$-poly(tetramethylene ether) glycol (MW= 2000)-($\varepsilon$-caprolactone)$_{4.5}$: $(CL)_{4.5}$-PTMG-$(CL)_{4.5}$, MW=3000] as a soft segment. Two melting peaks of TBG at about 14$^{\circ}C$ and 38$^{\circ}C$ were observed indicating the presence of two different crystalline domains composed of CL and PTMG dominant component. The effect of soft segment content (60-75 wt%) on the colloidal properties of dispersion, and thermal and mechanical properties of WBPU films, the water vapor permeability (WVP) and water resistance (WR) of WBPU-coated Nylon fabrics, and the adhesive strength of WBPU- coated layer and Nylon fabrics was investigated. As soft segment contents increased, the water vapor permeability of WBPU- coated Nylon fabrics increased from 3615 to 4502 g/$m^2$day, however, the water resistances decreased from 1300 to 500 mm$H_2$O.O.

• 한국전기전자재료학회논문지
• /
• 제31권7호
• /
• pp.475-480
• /
• 2018

We investigated the tribological properties of amorphous carbon (a-C) films deposited with CrC interlayers of various thicknesses as the adhesive layer. A-C and CrC thin films were deposited using the unbalanced magnetron (UBM) sputtering method with graphite and chromium as the targets. CrC films as the interlayer were fabricated under a-C films, and various structural, surface, and tribological properties of a-C films deposited with various CrC interlayer thicknesses were investigated. With various CrC interlayer thicknesses under a-C films, the tribological properties of CrC/a-C films were improved; the increased film thickness exhibited a maximum high hardness of over 27.5 GPa, high elastic modulus of over 242 GPa, critical load of 31 N, residual stress of 1.85 GPa, and a smooth surface below 0.09 nm at the condition of 30-nm CrC thickness.