• Korean Journal of Materials Research
• /
• v.4 no.6
• /
• pp.687-694
• /
• 1994

Heteroepitaxial InP/GaAs layers were grown using the selective liquid phase epitaxy (SLPE) technique. It was observed that the optimum LPE conditions were $660^{\circ}C$ growth temperature, $5^{\circ}C$ supercooling, and $0.4^{\circ}C$/min cooling rate. Maximum expitaxial layer overgrowth (ELO) of 110-160$\mu \textrm{m}$ was obtained when the seed was aligned along (112) orientation. Initial melt-back of the substrate was observed but limited to the seed region so that flat In-Ga-As-P layers were grpwn throughout the GaAs substrates. The InP/GaAs heteroepitaxial structure could be obtained by growing an additional InP layer on top of the In-Ga-As-P layer.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.13 no.3
• /
• pp.71-81
• /
• 2005

Anaerobic digestion is employed worldwide as the oldest and most important process for sludge stabilization. An additional advantage is the production of methane during anaerobic digestion. However, the waste activated sludge(WAS) has poor anaerobic degradability and less gas production due to the cell wall of bio-solid. In order to improve and enhance stabilization and dewatering of the WAS, a number of pretreatment processes have been developed and investigated. In this research, a pilot-scale study of pulse power pretreatment was performed to improve anaerobic degradability and dewaterability of the WAS. A pilot plant was designed and operated based on a previous laboratory study. Change of the sludge characteristics by pulse power pretreatment was estimated to assess the increasing soluble organics. The increased soluble organics could be used as a good substrate in the anaerobic digesion process. Gas production and methane potential of the anaerobic digestion were estimated as the parameters of anaerobic degradability. For evaluation of the dewaterability of pretreated WAS, capillary suction time(CST) and specific resistance were measured. The efficiency of energy recovery was also estimated by calculating energy balance.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2011.06a
• /
• pp.7-8
• /
• 2011

Basically, the lattice mismatch between film and substrate can make those BiFeO3(BFO) films distorted with strain structure. BFO phase can be stabilized on LaAlO3(LAO) represents the example of a multiferroic with giant axial ratio. Its crystal structure is not strictly tetragonal, but tetragonal with a slight monoclinic distortion and related to the rotation of the oxygen octahedra. In this study, we show that phases with a tetragonal-like epitaxial BFO films can indeed be ferroelectric and also can be stabilized via epitaxial growth onto LAO. Recent reports on epitaxial BFO films show that the crystal structure changes from nearly rhombohedral ("R-like") to nearly tetragonal("T-like") at strains exceeding approximately -4.5%, with the "T-like" structure being characterized by a highly enhanced c/a ratio. While both the "R-like" and the "T-like" phases are monoclinic, our detailed x-ray diffraction results reveal asymmetry change from MA and MC type, respectively. By applying additional strain or by modifying the unit cell volume of the film by substituting Ba for Bi, the monoclinic distortion in the "T-like" MC phase is reduced, i.e. the system approaches a true tetragonal symmetry. There are two different M-H loops for $Bi_{1-x}Ba_xFeO_{3-{\delta}}$(BBFO) and BFO films on SrTiO3(STO) & LAO substrates. Along with the ferroelectric characterization, these magnetic data indicate that the BFO phase stabilized on LAO represents the first example of a multiferroic with giant axial ratio. However, there is a significant difference between this phase and other predicted ferroelectrics with a giant axial ratio: its crystal structure is not strictly tetragonal, but tetragonal with a slight monoclinic distortion. Therefore, in going from bulk to highly-strained films, a phase sequence of rhombohedral(R)-to-monoclinic ["R-like" MA-to-monoclinic, "T-like" MC-to-tetragonal (T)] is observed. This sequence is otherwise seen only near morphotropic phase boundaries in lead-based solid-solution perovskites (i.e. near a compositionally induced phase instability), where it can be controlled by electric field, temperature, or composition. Our results show that this evolution can occur in a lead-free, stoichiometric material and can be induced by stress alone. Those major results are summarized as follows ; 1) Ba-doping increases the unit cell volume, 2) BBFO on LAO can be fully strained up to x=0.08 as a strain limit (Fig. 1), 3) P(E) & M(H) properties can be tuned by the variation of composition, strain, and film thickness.

• Journal of Oral Medicine and Pain
• /
• v.33 no.1
• /
• pp.1-8
• /
• 2008

It is well known that many antimicrobial proteins in saliva interact with each other. The purpose of the present study was to investigate the interactions of lysozyme with peroxidase in the aspects of enzymatic activity in vitro. The interactions of lysozyme with peroxidase were examined by incubating hen egg-white lysozyme(HEWL) with bovine lactoperoxidase(bLP). The influence of peroxidase system on lysozyme was examined by subsequent addition of potassium thiocyanate and hydrogen peroxide. Lysozyme activity was determined by turbidity measurement of a Micrococcus lysodeikticus substrate suspension. Peroxidase activity was determined with an NbsSCN assay. The Wilcoxon signed rank test was used to analyze the changes of enzymatic activities compared with their controls. bLP at physiological concentrations enhanced the enzymatic activity of HEWL(P < 0.05) and its effect was dependent on the concentration of peroxidase. However, HEWL did not affect the enzymatic activity of bLP. Thiocyanate did not affect the enzymatic activity of HEWL, either. The addition of potassium thiocyanate and hydrogen peroxide did not lead to additional enhancement of the enzymatic activity of HEWL. The changes of hydrogen peroxide concentration in the peroxidase system did not affect the enzymatic activity of HEWL. Collectively, despite an in vitro nature of our study, the results of the present study provide valuable information on the interactions of lysozyme and peroxidase in the aspects of enzymatic activity in oral health care products and possibly in the oral cavity.

• Journal of Ginseng Research
• /
• v.42 no.1
• /
• pp.42-49
• /
• 2018

Background: Ginsenoside F1 has been described to possess skin-whitening effects on humans. We aimed to synthesize a new ginsenoside derivative from F1 and investigate its cytotoxicity and melanogenesis inhibitory activity in B16BL6 cells using recombinant glycosyltransferase enzyme. Glycosylation has the advantage of synthesizing rare chemical compounds from common compounds with great ease. Methods: UDP-glycosyltransferase (BSGT1) gene from Bacillus subtilis was selected for cloning. The recombinant glycosyltransferase enzyme was purified, characterized, and utilized to enzymatically transform F1 into its derivative. The new product was characterized by NMR techniques and evaluated by MTT, melanin count, and tyrosinase inhibition assay. Results: The new derivative was identified as (20S)-$3{\beta},6{\alpha},12{\beta}$,20-tetrahydroxydammar-24-ene-20-O-${\beta}$-D-glucopyranosyl-3-O-${\beta}$-D-glucopyranoside(ginsenoside Ia), which possesses an additional glucose linked into the C-3 position of substrate F1. Ia had been previously reported; however, no in vitro biological activity was further examined. This study focused on the mass production of arduous ginsenoside Ia from accessible F1 and its inhibitory effect of melanogenesis in B16BL6 cells. Ia showed greater inhibition of melanin and tyrosinase at $100{\mu}mol/L$ than F1 and arbutin. These results suggested that Ia decreased cellular melanin synthesis in B16BL6 cells through downregulation of tyrosinase activity. Conclusion: To our knowledge, this is the first study to report on the mass production of rare ginsenoside Ia from F1 using recombinant UDP-glycosyltransferase isolated from B. subtillis and its superior melanogenesis inhibitory activity in B16BL6 cells as compared to its precursor. In brief, ginsenoside Ia can be applied for further study in cosmetics.

• Korean Journal of Materials Research
• /
• v.20 no.12
• /
• pp.676-680
• /
• 2010

Most TCOs such as ITO, AZO(Al-doped ZnO), FTO(F-doped $SnO_2$) etc., which have been widely used in LCD, touch panel, solar cell, and organic LEDs etc. as transparent electrode material reveal n-type conductivity. But in order to realize transparent circuit, transparent p-n junction, and introduction of transparent p-type materials are prerequisite. Additional prerequisite condition is optical transparency in visible spectral region. Oxide based materials usually have a wide optical bandgap more than ~3.0 eV. In this study, single-phase transparent semiconductor of $SrCu_2O_2$, which shows p-type conductivity, have been synthesized by 2-step solid state reaction at $950^{\circ}C$ under $N_2$ atmosphere, and single-phase $SrCu_2O_2$ thin films of p-type TCOs have been deposited by RF magnetron sputtering on alkali-free glass substrate from single-phase target at $500^{\circ}C$, 1% $H_2$/(Ar + $H_2$) atmosphere. 3% $H_2$/(Ar + $H_2$) resulted in formation of second phases. Hall measurements confirmed the p-type nature of the fabricated $SrCu_2O_2$ thin films. The electrical conductivity, mobility of carrier and carrier density $5.27{\times}10^{-2}S/cm$, $2.2cm^2$/Vs, $1.53{\times}10^{17}/cm^3$ a room temperature, respectively. Transmittance and optical band-gap of the $SrCu_2O_2$ thin films revealed 62% at 550 nm and 3.28 eV. The electrical and optical properties of the obtained $SrCu_2O_2$ thin films deposited by RF magnetron sputtering were compared with those deposited by PLD and e-beam.

• Korean Chemical Engineering Research
• /
• v.44 no.4
• /
• pp.404-409
• /
• 2006

The catalytic combustion of toluene over Pd-Cu/USY zeolite has been examined by using FT-IR spectroscopy in a closed system under dry and humid conditions. The catalytic combustion of toluene (700 ppmv) in the temperature range of $80-220^{\circ}C$ has been investigated by using a fixed bed reactor. The Pd-Cu/USY catalyst showed the highest catalytic performance with respects to the PdO-CuO/USY and Pd/USY. Comparing to $PdO/Al_2O_3$ catalysts, the slight improvement in conversion was observed over PdO/USY catalysts under humid condition since USY zeolite is hydrophobic substrate and water give an additional oxygen source to zeolite surface like oxygen. The reduced catalysts showed more enhanced catalytic activity due to the reduced activation energy of combustion of toluene than oxidized catalysts such as PdO/USY and PdO-CuO/USY.

• Journal of Life Science
• /
• v.30 no.2
• /
• pp.162-168
• /
• 2020

Because of a continual reduction in its domestic market share, the quality of the Makgeolli, a Korean traditional liquor, needs to be upgraded. Among the several options for quality improvement, sufficient organoleptic expression of flavor is very important. We analyzed production changes of isoamyl acetate, which has a banana smell, based on fermentation temperature and sugar content through the cultivation of S. cerevisiae 98-5 KCCM 11396P using generally polished rice. The banana flavor of that fermentation mash was organoleptically high at 20℃, but a larger amount of isoamyl acetate was obtained with a higher sugar content at 10℃, based on analysis by GC-MS. Consequently, sufficient production of banana flavor from isoamyl acetate was based on the concentration of isoamyl alcohol as a substrate compound of isoamyl acetate, and the production depended highly on the maintenance of heat stability, since it is unstable in temperature and the minimized inhibition of alcohol acetyl transferase by unsaturated fatty acids. We also found that production of the flavor component required the addition of sugar and a slightly higher temperature of 20~25℃ at the beginning stage of fermentation, with additional mash fermentation and a gradual decrease in temperature to 10~15℃.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.71-71
• /
• 2011

Dye-sensitized solar cells (DSCs) have drawn great academic attention due to their potential as low-cost renewable energy sources. DSCs contain a nanostructured TiO2 photoanode, which is a key-component for high conversion efficiency. Particularly, one-dimensional (1-D) nanostructured photoanodes can enhance the electron transport for the efficient collection to the conducting substrate in competition with the recombination processes. This is because photoelectron colletion is determined by trapping/detrapping events along the site of the electron traps (defects, surface states, grain boundaries, and self-trapping). Therefore, 1-D nanostructured photoanodes are advantageous for the fast electron transport due to their desirable features of greatly reduced intercrystalline contacts with specified directionality. In particular, anodic TiO2 nanotube (NT) electrodes recently have been intensively explored owing to their ideal structure for application in DSCs. Besides the enhanced electron transport properties resulted from the 1-D structure, highly ordered and vertically oriented nanostructure of anodic TiO2 NT can contribute additional merits, such as enhanced electrolyte diffusion, better interfacial contact with viscous electrolytes. First, to confirm the advantages of 1-D nanostructured material for the photoelectron collection, we compared the electron transport and charge recombination characteristics between nanoparticle (NP)- and nanorod (NR)-based photoanodes in DSCs by the stepped light-induced transient measurements of photocurrent and voltage (SLIM-PCV). We confirmed that the electron lifetime of the NR-based photoanode was much longer than that of the NP-based photoanode. In addition, highly ordered and vertically oriented TiO2 NT photoanodes were prepared by electrochemical anodization method. We compared the photovoltaic properties of DSCs utilizing TiO2 NT photoanodes prepared by one-step anodization and two-step anodization. And, to reduce the charge recombination rate, energy barrier layer (ZnO, Al2O3)-coated TiO2 NTs also applied in DSC. Furthermore, we applied the TiO2 NT photoanode in DSCs using a viscous electrolyte, i.e., cobalt bipyridyl redox electrolyte, and confirmed that the pore structure of NT array can enhance the performances of this viscous electrolyte.

• Journal of the East Asian Society of Dietary Life
• /
• v.18 no.6
• /
• pp.1056-1062
• /
• 2008

To evaluate the effect of irradiation on restructured pork jerky containing paprika and Japanese apricot extracts, the quality of protein was determined in vitro based on the formation of trypsin indigestible substrate inhibitor (TIS) and the computed protein efficiency ratio (C-PER) as determined based on the protein digestibility and amino acid analysis. In addition, we compared the effects of electron beam irradiation to those of gamma irradiation. Approximately 3% of the moisture content of pork jerky was reduced in response to irradiation with 3kGy administered using an electron beam however, no additional reduction was observed in samples that were subjected to higher doses of irradiation. In addition, there were no notable differences in the crude protein and fat content of pork jerky samples that were subjected to irradiation, regardless of dose. Furthermore, the total amino acids profiles did not change in response to electron beam irradiation. However, the in vitro protein digestibility increased by 7% in response to 3kGy of electron beam irradiation and 5kGy of gamma irradiation, but no significant changes in digestibility were not observed in response to treatment with higher doses. TIS quantified as trypsin inhibitors were formed in response to irradiation using the electron beam (3kGy) and gamma rays (5kGy), although there was a slight reduction in the production of TIS inhibitors in samples irradiated with higher doses. Moreover, only samples irradiated with 10kGy (electron beam and gamma ray) showed higher TBA values than those of the control samples. Finally, the C-PERs $(2.50{\sim}2.60)$ were greater in all of the irradiated pork jerky samples than in the control samples (2.22). Taken together, these results suggest that electron beam irradiation and the incorporation of extracts (paprika and Japanese apricot) may be useful methods of improving the nutritional quality of pork jerky.