• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.192-195
• /
• 2005

In this study, dynamic characteristics of an end-capped hull structure with surface bonded piezoelectric actuators are studied. Finite element modeling is used to obtain practical governing equation of motion and boundary conditions of smart hull structure. Modal analysis is conducted to investigate the dynamic characteristics of the hull structure. Piezoelectric actuators are attached where the maximum control performance can be obtained. Active controller based on Linear Quadratic Gaussian (LQG) theory is designed to suppress vibration of smart hull structure. It is observed that closed loop damping can be improved with suitable weighting factors in the developed LQG controller.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.718-721
• /
• 2007

The ionic-polymer-metal-composite actuators have the best merit for bio-mimetic locomotion because of their large bending performance. Especially, they have the advantage for mimicking a fish-like motion because IPMCs are useful to be actuated in water. So we have developed IPMC actuators with multiple electrodes for realization of biomimetic motion. This actuator is fabricated by combining electroless plating and electroplating techniques capable of patterning precisely and controlling a thickness of Pt electrode layer. The FRF analysis was conducted by a mechanical shaker and direct electrical excitation which is based on sweep sine wave function. From this result, the proper young‘s modulus of Platinum was investigated and applied on expecting the vibration characteristics of patterned IPMC actuator. The calculated maximum displacement of the patterned IPMC was 2.32mm under an applied 4mN/mm. The natural frequency was increased however displacement was decreased in according to increase a thickness of Pt.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.2
• /
• pp.48-56
• /
• 2001

This paper presents the position tracking control of a closed-loop cylinder system using electro-rheological (ER) valve actuators. After manufacturing three sets of cylindrical ER valves on the basis of Bingham model of ER fluid, a 3 dof(degree-freedom) closed-loop cylinder system having the heave, roll and pitch motions is constructed. The governing equations of motion are derived using Lagrange's equation and a control model is formulated by considering nonlinear characteristics of the system, Sliding mode controllers are the designed for these ER valve actuators in order to achieve position tracking control. The effectiveness of trajectory tracking control performance of the proposed cylinder system is demonstrated through computer simulation and experimental implementation of the sliding mode controller.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.484-487
• /
• 2006

In this paper, linear ultrasonic actuators are designed using two dimensional motions of a PMW-PT piezoelectric plate. By equalizing the natural frequencies of longitudinal and transverse vibration modes in the cantilever structure, the ultrasonic motion of the combined vibration modes are generated. We have designed two different PMN-PT actuators: one uses a tip attached on the edge of the actuator and it drives the object in the perpendicular direction of the tip. In other model, the actuator plate moves itself through stationary guides. Prototypes of the two models are manufactured and experiments results are compared to the theoretical and numerical results. The effects of structural characteristics and the friction force existing between the actuator tip and the moving object are considered. Experiments show the possibility of small size ultrasonic linear motors which can be applicable to small form factor information storage and phone camera actuators.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.119-123
• /
• 2006

The ionic-polymer-metal-composite actuators have the best merit for bio-mimetic locomotion because of their large bending performance. Especially, they have the advantage for mimicking a fish-like motion because IPMCs are useful to be actuated in water. So we have developed IPMC actuators with multiple electrodes for realization of biomimetic motion. Generally, the IPMC actuator has been fabricated in electroless plating technique, while it needs very long fabrication time and shows poor repeatability in the actuation performance owing to the variables in chemical fabrication process. Therefore, the novel fabrication methods were investigated by combining electroless plating and electroplating techniques capable of patterning precisely. On the whole, two different methods were compared and analyzed with similar thickness level of Platinum electrodes. Present results show that mixing chemical reduction and electroplating can be a promising candidate for electrode patterning.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.505-507
• /
• 2004

This paper attempts to compensate the nonlinearity between the input voltage and the output displacement of the piezoelectric stack in dynamic actuation by the following two ways. Firstly, the charge steering by circuit configuration reduces the hysteresis of piezoelectric actuator remarkably. However, it makes the ripple in positioning due to the phase lag and noise induced from the elements of the long closed loop. Secondly, the feedforward control by neural network compensates the hysteresis of the piezoelectric actuators effectively with the appropriate selection of the input variables for the training. The improvement of the dynamic performance of the piezoelectric actuators by the developed linearization technique is verified by experiments.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.3
• /
• pp.369-375
• /
• 2010

The two-dimensional finite element formulation for the basic field equations governing electrochemical responses of ionic conducting polymer-metal composite(IPMC) actuators is proposed in the present study. Biaxial deformation of a platinum plated Nafion actuator having 4 electrodes is dominated by electro-osmosis of hydrated ions and self-diffusion of free water molecules. Some numerical studies for IPMC actuators with electric field are carried out in order to show the validity of the proposed formulation and electric field analysis for the initial condition of total charge distribution are conducted using commercial code ANSYS/Emag.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1254-1258
• /
• 2007

Electro-active polymer (EAP), one of the smart materials, is a new alternative offering ultra-precise movements and bio-compatibility. We present the results of the design, fabrication, and performance evaluation of a fabricated diaphragm-type polymer actuator using segmented polyurethane(SPU). This paper illustrates the relationship between the elastic modulus and maximum deflection as a key property of the Maxwell stress effect and also presents the relationship between the dielectric constant and maximum deflection as a key property of the electrostriction effect, especially in polymer actuators using SPU. A diaphragm-type actuator was used to induce an equation of the vertically distributed load by using a fully clamped circular plate as the boundary condition. To verify the equation, the results were compared to the data measured from load cell. In the near future, a low-cost check valves and bio-robot can be applied by its actuators.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.546-549
• /
• 1995

This paper presents a control of washing machine using ER clutch and brake actuators. After analyzing field- dependent torque of the actuators on the basis of Bingham model of the ER fluid, two sets of cylindrical ER clutch and brake are manufactured. The governing equation of motion for washing and dehydrating are derived by considering actuators' dynamics. Subsequently, PID controllers are designed to achieve desired rotational motions and tracking control results are provided to demonstrate the effectiveness of the proposed method.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.3
• /
• pp.165-173
• /
• 2000

This Paper presents the position tracking control of a closed-loop cylinder system using electro-rheological(ER) valve actuators. After manufacturing three sets of cylindrical ER valves on the basis of Bingham model of ER fluid, a 3 dof(degree-of-freedom) closed-loop cylinder system having the heave, roll and pitch motions is constructed. The governing equations of motion are derived using Lagrange's equation and a control model is formulated by considering nonlinear characteristics of the system. Sliding mode controllers are then designed fer these ER valve actuators in order to achieve position tracking control. The effectiveness of trajectory tracking control performance of the proposed cylinder system is demonstrated through computer simulation and experimental implementation of the sliding mode controller.