• Journal of Forest and Environmental Science
• /
• v.9 no.1
• /
• pp.33-43
• /
• 1993

About 67% of all forest area in Korea belong to young age stands under II age class, including III age class which can be thinned under DBH 16cm, it comes up more than 90%. Therefore, thinking of the pressing necessity of thinning in our country this study describes the actual conditions analysis of the production of thinned small logs, points at issue and improvement measures of thinned timber production.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.1035-1040
• /
• 2003

This research investigates the actual data and construction technology of the massive bottom slab placed by $23,000m^3$ concrete quantity in site of the in-ground type LNG receiving terminal having 20,000kl storage capacity. The purpose of this study is to determine the optimum mix design and control the actual concreting procedures including concrete production, transportation, placement, vibrating and curing in site. For this purpose, the optimum mix design using ternary blended cement(furnace slag cement＋fly ash) and under piping method having 11 gates and 7 distributors are selected. As test results of actual construction, concrete placement is finished during 68hours with good success and obtained the good quality of the fresh and hardened concrete including slump, air contents, no-segregation, compressive strength and low hydration heat. Also, actual data for all of concrete procedures are proved successful and satisfied with our specifications.

• International Journal of CAD/CAM
• /
• v.6 no.1
• /
• pp.19-27
• /
• 2006

To survive in the current shipbuilding industry it is of vital importance for shipyards to achieve an optimal utilization of resources, make an achievable planning and ensure that this planning is kept. Possible problems should be eliminated before production starts and if unexpected disturbances occur in the actual production the right measures should be taken. Due to the dynamic nature of the production process, the continuous variation in products and the complexity of both, all this can hardly be achieved with conventional static planning and analysis systems. Simulation provides a solution here, since this enables the modelling and evaluation of the dynamic relations between product and production process. After a global introduction to production simulation in general and the application of simulation at the Flensburger shipyard, this paper presents a tool that has been developed to simulate the various complex assembly processes taking place at shipyards. Subsequently the simulation model for the subassembly production at Flensburger, in which this tool is applied, will be discussed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1233-1235
• /
• 2004

We have designed High Performance Prism LGP in 17 inch TFT-LCD. In test result to embody high brightness BLU in case of LGP of base and upper surface with 17 inch, thickness 8mm adding prism construct, it is superior brightness improvement than previous that of printing form about some 20% and in this course to embody actual material it succeeded prism LGP production by 17 inch injection form process.

• Journal of the Korean Society of Food Culture
• /
• v.11 no.2
• /
• pp.235-242
• /
• 1996

Sanitary management practices from 8 packaged meals (Dosirak) manufacturing establishments were surveyd during production and distribution and their microbiological quality of dosirak items marketed in CVS were analyzed. Correlation coefficients were calculated to deternine significant relationships between sanitary management practices and microbiological quality of packaged meals. The results of self evaluation on sanitary management practices indicated 'doing practice well' in personnel and equipment sanitation management but time-temperature control management were practiced satisfactorily only about 55% as compared with the managerial standard guidelines. Significant relationships between the status of actual sanitary management practices and microbiological quality of Dosirak items were not found, but general status of microbiological quality of Dosirak items revealed positive relationship with the size of operational structure and the status of time-temperature control management practices.

• Asian-Australasian Journal of Animal Sciences
• /
• v.8 no.4
• /
• pp.365-368
• /
• 1995

Lactation curves of dairy cows were generated using three models, namely; incomplete gamma function (model 1), polynomial inverse function (model 2) and non-linear regression (model 3). Secondary milk yield data of 27 cows which had completed 6 lactations were used in this study. Milk yield records (once a week) throughout the lactation and from the first three months of lactation were fitted to the models. Estimation of total milk yield by model 3 using the data once a week throughout the lactation resulted in smaller % bias and standard error than those generated from model 1 and 2. But, model 2 was more accurate in predicting the 305-day milk yield equivalent closer to actual yields with smaller bias % and error using partial records up to 3 months. Also, model 2 was able to estimate the time to reach peak yield close to the actual data using partial records and model 2 could be used as a tool to advise farmers on appropriate feeding and management practices to be adopted.

• Transactions of Materials Processing
• /
• v.8 no.2
• /
• pp.200-207
• /
• 1999

To increase dimensional accuracy of strip width, model to compensate width spread during roughing mill has been developed. To measure the amount of width spread during the production rolling more precisely, special roughing rolling procedures for the horizontal rolling and dog-bone rolling were designed in the actual production mill. From the operational data analysis, it is known that the prime factors influencing on the width spread were strip width, strip thickness, edging amount, number of pass and type of edger roll etc., Based upon the statistical analysis of rolling data, new models which can predict width spread during horizontal rolling and dog-bone rolling were developed and tested on the actual processing conditions for the reliability. The application test showed that newly developed model gave fairly accurate predictions on the width spread during roughing passes.

• Journal of Industrial Technology
• /
• v.31 no.A
• /
• pp.119-122
• /
• 2011

AWS (Automated Weather Station) wind data was used to predict the annual energy production of Gangwon wind farm having a total capacity of 98 MW in Korea. Two common wind energy prediction programs, WAsP and WindSim were used. Predictions were made for three consecutive years of 2007, 2008 and 2009 and the results were compared with the actual annual energy prediction presented in the CDM (Clean Development Mechanism) monitoring report of the wind farm. The results from both prediction programs were close to the actual energy productions and the errors were within 10%.

• Journal of the Korean earth science society
• /
• v.34 no.7
• /
• pp.633-644
• /
• 2013

This study evaluates wind farm efficiency at Haengwon in Jeju Island. The actual energy production at Haengwon wind farm is compared with the estimated energy production based on Korean wind map which is developed at the National Institute of Meteorological Research/KMA. The validation of wind map at Gujwa located near the Haengwon wind farm shows that the wind speed is overestimated. The diurnal variation of wind speed shows a maximum value in the afternoon due to the effect of sea-land breeze. The ratio of the actual energy production at Haengwon wind farm and the estimated energy production based on the Korean wind map is 24.8%, while the distribution of energy frequency is similar each other. The difference of energy production is caused by mechanical error of the turbine and the overestimation of the simulated wind map. This study will contribute to the repowering of turbines for improving the efficiency of wind farm in the future.

• Journal of Software Assessment and Valuation
• /
• v.17 no.2
• /
• pp.101-107
• /
• 2021

Animation production is collaborated by many experts and gives many ideas for new and interesting video production. Interesting video production is a problem directly related to the success of the project, so it can be said that it is better to create an environment that is not burdened with technical aspects in expressing ideas. In the actual keyframe animation production environment, ideas are frequently modified to obtain better results, and techniques that are re-used so that the animation key pose data developed at the early stage of the possible stage can be rewritten without abandoning it, and functions that can temporarily change the center of gravity contribute to the productivity of animation work and greatly help the creator to improve the creative atmosphere. This study analyzes action animations implemented in computer animation software to examine the factors that hinder actual productivity, and derives the technical concepts that can contribute to the improvement of animation production productivity and the necessity of developing related tools.