• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.302-305
• /
• 2007

In recent years, many researches on new storage media with high capacity and information are developing. For manufacture of optical storage with high capacity, the injection molding process is generally used. In order to increase the filling ratio of the injection molding structure, the injection molding process required for high injection pressure, packing pressure and temperature control of the mold. However, conventional injection molding process is difficult to increase the filling ratio using injection master with the range of several nanometers and high aspect ratio. In order to improve and increase filling ratio of nano-structure with high aspect ratio, the active temperature control of injection mold was used. Experimental conditions were used injection pressure, time and temperature. Consequently, by using the peltier device into injection mold, we carried out the efficient and active temperature control of mold at low cost.

• Applied Chemistry for Engineering
• /
• v.10 no.3
• /
• pp.415-418
• /
• 1999

The characteristics of VRLA (valve regulated Iead-acid) battery with the tubular positive plate and gel type electrolyte were examined as a function of active material filling density. The filling density of positive plate was 3.2 g/mL, 3.4 g/mL, and 3.6 g/mL, respectively. These VRLA batteries were cycled with 100% DOD (depth of discharge) at the $C_5/5$ rate, followed by IU-type recharge with $I_{max}=0.2C_{10}/10$ and a final voltage V=2.40 V/cell. The test was performed in a thermostatic room at $25{\pm}1^{\circ}C$. The result indicated that the initial capacity was independent of active material filling density, i.e., the highest initial capacity was 3.4 g/mL of filling density and the lowest was 3.6 g/mL. On aspect of the cycle-life performance of the VRLA battery, the filling density of 3.6 g/mL was similar to that of 3.4 g/mL in the positive plate, and both were higher than that of 3.2 g/mL. Water-loss and degradation of the VRLA battery were decreased according to an increase of the filling density in the positive plate. The optimum filling density of the active material was 3.4~3.6 g/mL.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.5
• /
• pp.905-911
• /
• 2005

We propose an efficient adaptive subcarrier selection scheme, in which the active subcarriers and their modulation and coding schemes (MCSs) are selected at the receiver, and subsequently conveyed to the transmitter using limited feedback We theoretically show that capacity maximization can be achieved by selecting subcarriers with highest signal-to-noise ratios (SNRs) and adapting the number of active subcarriers according to channel environments. Furthermore, an ordering based adaptive subcarrier selection algorithm is proposed to select the optimal active subcarriers with low complexity. Numerical results show that the proposed adaptive subcarrier selection scheme provides higher capacity than that obtained by water-filling approaches, even with limited feedback.

• 정보저장시스템학회:학술대회논문집
• /
• 2005.10a
• /
• pp.26-30
• /
• 2005

Stamper surface temperature is very critical in replicating the high density optical disc substrates using injection molding as the pit or land/groove patterns on the optical disc substrate have decreased due to the rapid increase of areal density. During the filling stage, the polymer melt in the vicinity of the stamper surfaces rapidly solidifies and the solidified layer generated during polymer filling greatly deteriorates transcribability and fluidity of polymer melt. To improve transcribability and fluidity of polymer melt, stamper surface temperature should be controlled such that the growth of the solidified layer is delayed during the filling stage. In this study, the effect of heating on replication process was simulated numerically. Then, an injection mold equipped with instant active heating system was designed and constructed to raise the stamper surface temperature over the glass transition temperature during filling stage of the injection molding. Also, the closed loop controller using the Kalman filter and the linear quadratic Gaussian regulator was designed. As a result, the stamper surface temperature was controlled according to the desired reference stamper surface temperature.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.2
• /
• pp.100-104
• /
• 2006

Stamper surface temperature is very critical in replicating the high density optical disc substrates using injection molding as the pit or land/groove patterns on the optical disc substrate have decreased due to the rapid increase of areal density. During the filling stage, the polymer melt in the vicinity of the stamper surfaces rapidly solidifies and the solidified layer generated during polymer filling greatly deteriorates transcribability and fluidity of polymer melt. To improve transcribability and fluidity of polymer melt, stamper surface temperature should be controlled such that the growth of the solidified layer is delayed during the filling stage. In this study, the effect of heating on replication process was simulated numerically. Then, an injection mold equipped with instant active heating system was designed and constructed to raise the stamper surface temperature over the glass transition temperature during filling stage of the injection molding. Also, the closed loop controller using the Kalman filter and the linear quadratic Gaussian regulator was designed. As a result. the stamper surface temperature was controlled according to the desired reference stamper surface temperature.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.48 no.5
• /
• pp.397-401
• /
• 2003

This experiment was conducted to know the characteristics of kernel growth as affected by various temperature regimes during grain filling using the varieties Hwaseongbyeo, Ilpumbyeo and Chucheongbyeo. The rice plants tested were grown in the natural condition at 1/5000a Wagner pots until flowering. After flowering, the rice plants were moved to controlled temperature conditions in a phytotron. The minimum/maximum daily temperature in the phytotron was controlled by 12/18, 15/21, 18/24, 21/27, and 24/$30^{\circ}C$, respectively. The grain weights were measured every three days after treatment. The mean daily kernel growth rate during active grain filling period showed different responses among varieties under various temperature regimes. The kernel growth rate of Chucheongbyeo was seriously reduced as temperature regimes were decreased. However, that of Ilpumbyeo was not influenced so critically. Ilpumbyeo showed some advantages in grain filling under low temperature regimes compared to Chucheongbyeo. The lag phase in grain filling of Chucheongbyeo was the longest among tested varieties, followed by Hwaseongbyeo under daily mean temperature regime of $15^{\circ}C$. Kernel weight of Ilpumbyeo increased fast in early grain filling phase under low temperature. This characteristic may be favorable for grain filling in temperate zone where the daily mean temperature is drastically dropped during grain filling period. Regression analysis with kernel growth rate and temperature showed the estimated critical low temperature for grain filling among varieties were $9^{\circ}C$, $12^{\circ}C$, $13^{\circ}C$ in Ilpumbyeo, Hwaseongbyeo and Chucheongbyeo, respectively. Under moderate temperature the duration of grain filling of Ilpumbyeo was longer than that of Chucheongbyeo. However, Under low temperature that of Ilpumbyeo was more favorable than Chucheongbyeo.

• Journal of Digital Convergence
• /
• v.10 no.3
• /
• pp.167-172
• /
• 2012

This paper presents the technique separating objects on the single frame image from the background using region segmentation technique based on active contour. Active contour is to extract contours of objects from the image, which is set to have multi-search starting point to extract each objects contours for multi-object segmentation. Initial rough object segments are generated from binary-coded image using object specific contour information, and then the hole filling is performed to compensate internal segmentation caused by the change of inner object hole area and pixels. This procedure complements the problems caused by the noise from the region segmentation and the errors of segmentation near by the contour. The proposed method and conventional method is compared to verify the superiority of the proposed method.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05b
• /
• pp.531-534
• /
• 2012

본 논문에서는 Active Contour 기반의 영역 분할에서 이미지의 초점값을 이용하여 분할된 영역 사이의 경계를 생성하여 기존의 Active Contour에서 발생할 수 있는 중첩 객체의 동일 객체 인식을 방지하는 기법을 제안한다. Active Contour는 영상에서 객체의 윤곽을 검출하여 윤곽을 기준으로 영상을 분할하지만 중첩되거나 근접한 객체에서의 분할이 정확하게 이루어지지 않아 동일 객체로 인식하는 단점이 있다. 이러한 객체에서의 분할을 위해 영상의 초점값을 이용하여 영상 내에 존재하는 객체의 유사 경계 영역을 생성하고 Active Contour의 결과에 적용하여 경계를 생성한 뒤 초점값 적용으로 인해 생성될 수 있는 홀 영역을 hole filling 과정을 수행하여 보완함으로써 보다 정확한 객체를 추출하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.351.1-351.1
• /
• 2014

In this study, we prepared the solution-based In-Ga-Zn oxide thin film transistors (IGZO TFTs) of multistacked active layer and characterized the gate bias instability by measuring the change in threshold voltage caused by stacking. The solutions for IGZO active layer were prepared by In:Zn=1:1 mole ratio and the ratio of Ga was changed from 20% to 30%. The TFTs with multistacked active layer was fabricated by stacking single, double and triple layers from the prepared solutions. As the number of active layer increases, the saturation mobility shows the value of 1.2, 0.8 and 0.6 (). The electrical properties have the tendency such as decreasing. However when gate bias VG=10 V is forced to gate electrode for 3000 s, the threshold voltage shift was decreased from 4.74 V to 1.27 V. Because the interface is formed between the each layers and this affected the current path to reduce the electrical performances. But the uniformity of active layer was improved by stacking active layer with filling the hole formed during pre-baking so the stability of device was improved. These results suggest that the deposition of multistacked active layer improve the stability of the device.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.5
• /
• pp.1951-1972
• /
• 2018

Wi-Fi Access Point (AP) optimization approaches are used in indoor positioning systems for signal coverage enhancement, as well as positioning precision improvement. Although the huge power consumption of the AP optimization forms a serious problem due to the signal coverage requirement for large-scale indoor environment, the conventional approaches treat the problem of power consumption independent from the design of indoor positioning systems. This paper proposes a new Fast Water-filling algorithm Group Power Constraint (FWA-GPC) based Wi-Fi AP optimization approach for indoor positioning in which the power consumed by the AP optimization is significantly considered. This paper has three contributions. First, it is not restricted to conventional concept of one AP for one candidate AP location, but considered spare APs once the active APs break off. Second, it utilizes the concept of water-filling model from adaptive channel power allocation to calculate the number of APs for each candidate AP location by maximizing the location fingerprint discrimination. Third, it uses a fast version, namely Fast Water-filling algorithm, to search for the optimal solution efficiently. The experimental results conducted in two typical indoor Wi-Fi environments prove that the proposed FWA-GPC performs better than the conventional AP optimization approaches.