• Journal of Electrical Engineering and Technology
• /
• 제12권5호
• /
• pp.1812-1820
• /
• 2017

This paper analyzes a symmetric active cell balancer for a battery management system. The considered cell balancer uses a forward converter in which the circuit structure is symmetric. This cell-balancing method uses fewer switches and is simpler than the previously proposed active cell-balancing circuits. Active power switches of this cell-balancing circuit operate simultaneously with the same pulse width modulation signals. Therefore, this cell-balancing circuit requires less time to be balanced than a previous bidirectional-forward-converter-based cell balancer. This paper analyzes the operational principles and modes of this cell balancer with computer-based circuit simulation results as well as experimental results in which each unbalanced cell is equalized with this cell balancer. The maximum power transfer efficiency of the investigated cell balancer was 87.5% from the experimental results. In addition to the experimental and analytical results, this paper presents the performance of this symmetric active cell-balancing method.

• 전기학회논문지
• /
• 제66권5호
• /
• pp.786-791
• /
• 2017

In this paper, the run time of Li-polymer secondary cell with and without Active Balancing BMS is analyzed. The Active Balancing System using Flyback Converter with two-way power control facility, his designed for optimal characteristics of balancing. The run time of Li-polymer secondary cell is drastically increased employing the Flyback Convert Active Balancing BMS. The run time performance of Li-polymer secondary cell with or without Flyback Converter Active Balancing BMS is analyzed with the discharging and charging experiment of Li-polymer secondary cell.

• Journal of Electrical Engineering and Technology
• /
• 제12권1호
• /
• pp.29-38
• /
• 2017

This paper presents a study on the state-of-charge (SOC) reference based active cell balancing in real-time. The optimal references of SOC are determined by using the proposed active cell balancing system with the bidirectional DC/DC converters via the dual active bridge (DAB) type. Then, the energies between cells can be balanced by the power flow control of DAB based bidirectional DC/DC converters. That is, it provides the effective management of battery by transferring energy from the strong cell to the weak one until the cell voltages are equalized to the same level and therefore improving the additional charging capacity of battery. In particular, the cell aging of battery and power loss caused from energy transfer are considered. The performances of proposed active cell balancing system are evaluated by an electromagnetic transient program (EMTP) simulation. Then, the experimental prototype is implemented in hardware to verify the usefulness of proposed system.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.1889-1891
• /
• 2004

The differential white blood cell count plays an important role in the diagnosis of different diseases. It is a tedious task to count these classes of cell manually. An automatic counter using computer vision helps to perform this medical test rapidly and accurately. Most commercial-available automatic white blood cell analysis composed mainly 3 steps including segmentation, feature extraction and classification. In this paper we concentrate on the first step in automatic white-blood-cell analysis by proposing a segmentation scheme that utilizes a benefit of active contour. Specifically, the binary image is obtained by thresolding of the input blood smear image. The initial shape of active is then placed roughly inside the white blood cell and allowed to grow to fit the shape of individual white blood cell. The white blood cell is then separated using the extracted contour. The force that drives the active contour is the combination of gradient vector flow force and balloon force. Our purposed technique can handle very promising to separate the remaining red blood cells.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.393-397
• /
• 2001

This paper addresses an Intelligent Agent-based Open Architecture Cell Controller for Intelligent Manufacturing System(IMS). With an Intelligent Agent approach, the IMS will be a independent, autonomous, distributed system and achieve a adaptability to change of manufacturing environment. As the development methodology of Open Architecture Cell Controller, an object-oriented modeling technique is employed for building models associated with IMS operation, such as resource model, product model, and control model. Intelligent Agent-based Open Architecture Cell Controller consists of two kinds of dependant agents, that are the active agent and the coordinator agent. The Active agent is contributed to control components of IMS in real-time. The coordinator agent has great role in scheduling and planning of IMS. It communicates with other active agents to get information about status on system and generates the next optimal task through the making-decision logic and dispatch it to other active agent.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권4호
• /
• pp.631-640
• /
• 2016

A dual-mode power management for a hybrid-electric UAV with a cruise power of 200W is proposed and empirically verified. The subject vehicle is a low-speed long-endurance UAV powered by a solar cell, a fuel cell, and a battery pack, which operate in the same voltage bounds. These power sources of different operational characteristics can be managed in two different methods: passive management and active management. This study proposes a new power management system named PMS2, which employs a bypass circuit to control the individual power sources. The PMS2 normally operates in active mode, and the bypass circuit converts the system into passive mode when necessary. The output characteristics of the hybrid system with the PMS2 are investigated under simulated failures in the power sources and the conversion of the power management methods. The investigation also provides quantitative comparisons of efficiencies of the system under the two distinct power management modes. In the case of the solar cell, the efficiency difference between the active and the passive management is shown to be 0.34% when the SOC of the battery is between 25-65%. However, if the SOC is out of this given range, i.e. when the SOC is at 90%, using active management displays an improved efficiency of 6.9%. In the case of the fuel cell, the efficiency of 55% is shown for both active and passive managements, indicating negligible differences.

• ETRI Journal
• /
• 제39권6호
• /
• pp.859-865
• /
• 2017

This paper presents a method for determining the optimum active-area width (OAW) of solar cells in a module architecture. The current density-voltage curve of a reference cell with a narrow active-area width is used to reproduce the current density profile in the test cell whose active area width is to be optimized. We obtained self-consistent current density and electric potential profiles from iterative calculations of both properties, considering the distributed resistance of the contact layers. Further, we determined the OAW that yields the maximum efficiency by calculating efficiency as a function of the active-area width. The proposed method can be applied to the design of the active area of a dye-sensitized solar cell in Z-type series connection modules for indoor and building-integrated photovoltaic systems. Our calculations predicted that OAW increases as the sheet resistances of the contact layers and the intensity of light decrease.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1174-1175
• /
• 2008

A operation scheme to regulate the active power output of the hybrid system consisted of a doubly fed induction generator(DFIG) and a fuel-cell are presented. The power output of the wind turbine fluctuates as the wind speed varies and the slip power between the rotor circuit and power converter varies as the rotor speed change. A fuel cell system can be individually operated and adjusted output power. In this paper, a fuel-cell is performed to regulate the active output power in comparison with the active power output of a DFIG. Based on PSCAD/EMTDC power system tools, we simulated a DFIG and a fuel cell and investigated about dynamics of the output power in hybrid system.

• International Journal of Stem Cells
• /
• 제15권3호
• /
• pp.283-290
• /
• 2022

Background and Objectives: Difficulties often encountered in separating and purifying active muscle satellite cells (MSCs) from skeletal muscle tissues have limited the supply of cells for muscle therapy and artificial meat production. Here, we report an effective isolation protocol to economically and conveniently retrieve active MSCs from skeletal muscle tissues in mice. Methods and Results: We optimized an enzyme-based tissue digestion protocol for isolating skeletal muscle-derived primary cell population having a large number of active MSCs and described a method of differential plating (DP) for improving purity of active MSCs from skeletal muscle-derived primary cell population. Then, the age of the mouse appropriate to the isolation of a large number of active MSCs was elucidated. The best isolation yield of active MSCs from mouse skeletal muscle tissues was induced by the application of DP method to the primary cell population harvested from skeletal muscle tissues of 2-week-old mice digested in 0.2% (w/v) collagenase type II for 30 min at 37℃ and then in 0.1% (w/v) pronase for 5 min at 37℃. Conclusions: The protocol we developed not only facilitates the isolation of MSCs but also maximizes the retrieval of active MSCs. Our expectation is that this protocol will contribute to the development of original technologies essential for muscle therapy and artificial meat industrialization in the future.

• 한국콘텐츠학회논문지
• /
• 제11권5호
• /
• pp.84-92
• /
• 2011

바이오 영상에서 세포 영역의 자동 분할 기술은 생물학자들이 복잡한 세포의 기능을 이해하는데 도움을 주고, 수작업을 통해 세포를 분석하던 일들을 자동적으로 처리해주는 매우 중요한 기술이다. 기존의 멀티채널 영상으로부터 세포핵 및 세포를 분할하는 방법은 DNA 채널을 이용하여 세포핵을 검출하고, 이를 초기 윤곽으로 하여 Actin 채널에서 밝기 기반의 Active Contour 모델을 통해 세포를 분할하는 2 단계의 과정을 거친다. 그러나 세포 분할 과정에서 채널 간 상관성으로 인해 발생하는 세포 내 불균일한 밝기 문제를 고려하지 않은 채, 밝기 기반의 Active Contour 모델을 적용하여 분할의 성능이 저하되는 문제점이 발생한다. 따라서 본 논문에서는 DNA 와 Actin 채널 간 상관성을 고려하여, DNA 채널 정보를 통해 Actin 채널 내부의 밝기를 균일하게 보정함으로써 밝기 기반의 Active Contour 모델이 세포 분할에 잘 적용 될 수 있는 전처리 알고리즘을 제안한다. 실험을 통해 제안 전처리 과정을 거친 세포 분할 방법의 성능이 기존 방법에 비해 객관적, 주관적으로 크게 향상됨을 증명한다.