• Journal of Welding and Joining
• /
• 제18권2호
• /
• pp.69-76
• /
• 2000

Formation of the weld defect, such as a blowhole and a pit in lap-jointed fillet arc welds has been a serious problem in arc welding Zn-coated steel sheet. In this study, the relationship among welding conditions, welding materials and defect formation was investigated in order to minimize these defects in the CO₂welds. In addition, the arc stability of the commercial welding wires was evaluated for revealing their effects on defect formation. Main conclusions obtained are as follows: 1) There was no difference between shear tensile strength of the sound welds and that of the welds with blowholes whose diameters are less than 0.5mm. However, the welds with blowholes whose diameters are equal or large than 0.5mm and pits exhibited tensile strength 10∼ 20% and 30∼40% lower than that of the sound welds respectively. 2) The optimum welding condition to effectively prevent or reduce the weld defects formation are as follows: -The welding variables of 220A-23V-100cm/min and 120A-19V-30cm/min were recommended for minimizing the weld defects. -The gap between the two sheets at the lap-joint should be controlled to more than 0.2mm. -Solid wire was less susceptible to the formation of the weld defects than the flux-cored wire. -The low welding current condition produced less weld defects than the high welding current condition. 3) One of the reason why the amount of the defect was reduced at the low welding current was the gas discharging by the active agitation of the molten pool, due to an increasing in the number of the short circuit.

• 한국지리정보학회지
• /
• 제5권4호
• /
• pp.93-105
• /
• 2002

본 연구는 시 공간적 유동성을 갖고 있는 우리나라 산불 현황정보를 인터넷상에 시각적으로 표출함으로써 일반 사용자 누구나 쉽게 산불정보에 접근 가능하도록 한다. 아울러 산불관련 공무원들이 이들 정보를 실시간에 효율적으로 관리 감독을 할 수 있도록 웹상에서 정보의 입력 및 검색, 출력이 가능한 실무자 중심의 인터페이스를 개발하였다. 본 시스템에서의 웹 서버는 MS사의 IIS 5.0을 이용하였으며 데이터베이스 구축과 웹상에서 동적인 웹 페이지를 동작시키기 위해서는 Oracle 8i와 ASP(active server page)를 각각 사용하였다. 또한, 웹상에서 처리된 정보를 사용자들에게 지도데이터로 서비스하기 위한 맵 서버로는 ESRI사의 ArcGIS IMS(internet map server)와 이들을 제어하고 개발하기 위한 시스템 개발 언어로는 Java, VB 6.0, HTML을 이용하였다. 본 시스템을 통해 운영되는 12년 간의 다양한 산불관련 현황데이터를 바탕으로 우리나라 산불 경향과 현황을 쉽게 파악할 뿐만 아니라 이들 정보의 시각화는 국내 산불관련 정책결정 시 의사결정지원시스템으로서도 그 활용성이 클 것이라 사료된다. 나아가 일반국민들에게는 산불예방에 대한 경각심을 고취하고 관련 공무원들에게는 과학적이고 체계적인 산불 행정업무를 수행할 수 있도록 하는 기반을 마련하리라 기대된다.

• 공업화학
• /
• 제35권4호
• /
• pp.321-328
• /
• 2024

불화탄소 기반 리튬일차전지(Li/CF_X)의 활물질로 이용되는 불화탄소는 낮은 전도성에 기인한 열악한 율속 특성으로 방전 성능이 제한적이다. 따라서, 본 연구에서는 이를 극복하기 위하여 불화탄소에 열분해 연료유를 이용하여 탄소 코팅을 진행하였고, 전기화학적 성능을 고찰하였다. 탄소 코팅에 의하여 불화탄소 표면에 무정형 탄소층이 형성되었으며, 열처리 온도에 따른 불화탄소의 표면 물리화학적 특성을 면밀히 고찰하였다. 상용 불화탄소를 450 ℃에서 열처리한 ARC@C450 샘플은 sp² 탄소 결합의 함량이 62%로 가장 크게 증가하였으며, 반이온성 C-F 결합이 가장 많이 형성되었다. 또한, ARC@C450 샘플을 환원극 활물질로 이용한 일차전지는 가장 높은 5 C 율속(392 mAh/g)에서 안정적인 방전 특성을 보였으며, R_ct 값은 미처리 시료에 비하여 53% 감소하였다. 따라서, 본 연구에서는 불화탄소의 낮은 전도성을 극복하기 위한 방법으로 열분해 연료유 기반 탄소 코팅을 제안하며, 탄소 코팅된 불화탄소는 우수한 율속 성능을 나타냄으로 고출력 일차전지로의 응용 가능성을 제시한다.

• Journal of Yeungnam Medical Science
• /
• 제16권1호
• /
• pp.15-24
• /
• 1999

Although traditionally viewed as a physical barrier between the host and a variety of inhaled irritants and pathogens, it has become clear that the epithelium has a much broader functional scope. Epithelial cells arc metabolically active and can play an important role in the regulation of the allergic inflammatory response. This review provides a consideration of the role of the epithelial cell as both a "target" for exogenous and endogenous stimuli and as an "effector" cell that is capable of producing a variety of products that can influence the inflammatory response in the airways.

• 한국표면공학회지
• /
• 제37권2호
• /
• pp.128-136
• /
• 2004

Effects of alloying elements on the surface characteristics of Fe-38Al intermetallic compounds were investigated using potentiostat. The specimens were casted by the vacuum arc melting. The subsequent homogenization and the stabilization led to the homogeneous DO$_3$ structure of the specimen. After the corrosion tests, the surface of the tested specimen was observed by the optical microscopy and scanning electron microscopy(SEM). For Fe-38 at.% Al intermetallic compound, the addition of Cr and Mo proved to be beneficial in decreasing the grain boundary attack by decreasing the active current density. Addition of Band Nb resulted in a higher active current density and also a higher passive current density. These results indicated the role of Cr and Mo in improving the pitting corrosion resistance of Fe-38 at.%Al intermetallic compound. Band Nb addition to Fe-38 at.%Al accelerated the granular corrosion. Fe-38 at.%Al containing Cr and Mo showed remarkably improved pitting corrosion resistance in comparison with Band Nb addition to Fe-38 at. %Al.

• Journal of Welding and Joining
• /
• 제34권2호
• /
• pp.36-45
• /
• 2016

Recent developing tendency for technologies of high efficient brazing are studied by searching of NDSL, Science Direct, KIPRIS, PCT and so on. Active metal brazing, arc brazing, fluxless brazing, brazing with low melting point, reactive air brazing, laser brazing, laser droplet brazing are investigated. By optimal selecting of the above mentioned technologies, it needs to investigate an economical metallurgical design and the advanced brazing methods. To improve the embrittlement of intermetallic compound at brazing interface, it must be studied the inexpensive variant metals including nonmetals and the heat sources(MIG, TIG, Laser) by hybrid techniques.

• 자동차안전학회지
• /
• 제5권1호
• /
• pp.37-43
• /
• 2013

This paper describes an investigation into coordinated control of electronic stability control (ESC) and active roll control system (ARS). The coordinated control is suggested to improve the vehicle stability and agility features by yaw rate control. The proposed integrated chassis control algorithm consists of a supervisor, control algorithms, and a coordinator. The supervisor monitors the vehicle status and determines desired vehicle motions such as a desired yaw rate and desired roll motion based on control modes to improve vehicle stability. According to the corresponding the desired vehicle dynamics, the control algorithm calculated a desired yaw moment and desired roll moment, respectively. Based on the desired yaw moment and the desired roll moment, the coordinator determines the brake pressures and the ARC motor torques based on control strategies. Closed loop simulations with a driver-vehicle-controller system were conducted to investigate the performance of the proposed control strategy using CarSim vehicle dynamics software and the integrated controller coded using Matlab/Simulink.

• Transactions on Electrical and Electronic Materials
• /
• 제15권5호
• /
• pp.275-278
• /
• 2014

We deposited TiAgN and ZrAgN nanocomposite coatings on pure Titanium specimens, by using arc ion plating (AIP) with single alloy targets. TiAg ZrAg alloy targets of 5 wt.%, 10 wt.% silver content by vacuum arc remelting (VAR), followed by homogenization for 2 hours at $1,100^{\circ}C$ in non-active Ar gas atmosphere and characterized these samples for morphology and chemical composition. We investigated the biocompatibility of TiAg and ZrAg alloys by examining the proliferation of L929 fibroblast cells by MTT test assay, after culturing the cells ($4{\times}10^4cells/cm^2$) for 24 hours; and exploring the antibacterial properties of thin films by culturing Streptococus Mutans (KCTC3065), using paper disk techniques. Our results showed no cytotoxic effects in any of the specimens, but the antibacterial effects against Streptococus Mutans appeared only in the 10 wt.% silver content specimens.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.229-229
• /
• 2010

We report a high crystalline nonpolar a-plane (11-20) GaN on r-plane (1-102) sapphire substrates with $+0.15^{\circ}$, $-0.15^{\circ}$, $+0.2^{\circ}$, $-0.2^{\circ}$ and $+0.4^{\circ}$ misoriented by metalorganic chemical-vapor deposition (MOCVD). The multi-quantum wells (MQWs) active region is consists of 5 periods the nonpolar a-plane InGaN/GaN (a-InGaN/GaN) on a high quality a-plane GaN (a-GaN) template grown by using the multibuffer layer technique. The full widths at half maximum (FWHMs) of x-ray rocking curve (XRC) obtained from phiscan of the specimen that was grown up to nonpolar a-plane GaN layers with double crystal x-ray diffraction. The FWHM values of $+0.4^{\circ}$ misoriented sapphire substrate were decreased down to 426 arc sec for $0^{\circ}$ and 531 arc sec for $-90^{\circ}$, respectively. Also, the samples were characterized by photoluminescence (PL).

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.226-233
• /
• 1998

In this paper, an experimental study was performed to investigate the speed ratio-torque-thrust characteristics for metal belt CVT. It is observed from the experimental results that nondimensional secondary thrust force follows with the existing theoretical formula with ${\mu}$=0.09~0.12 depending on the torque and the speed ratio. In order to represent these characteristics, an effective friction coefficient was introduced. Also, the slip characteristics between the belt and the pulley were investigated experimentally and traction coefficients at gross slip were obtained for various speed ratios. Using the traction coefficients and the effective friction coefficients, an improved formula for the secondary thrust force was suggested assuming that thrust force is the summation of the thrust of pseudo inactive arc and the thrust of pseudo active arc. The effective friction coefficient and the improved formula for the speed ratio-torque-thrust relationship suggested in this work can be used to obtain the appropriate secondary thrust.