• Clean Technology
• /
• v.17 no.1
• /
• pp.48-55
• /
• 2011

The application of fibrous activated carbon (FAC)-titanium dioxide ($TiO_2$) hybrid system has not been reported yet for the control of malodorous dimethyl sulfide (DMS) at residential environmental levels. Accordingly, the current study was designed not only to characterize this hybrid system using x-ray diffraction method, particulate surface measurement and Fourier transform Infrared (FTIR) method, but also to evaluate its adsorptional photocatalytic activity (APA) for the DMS removal. The physical/surface characteristics of FAC-$TiO_2$ which was prepared in this study suggested that the hybrid material might have certain APA for DMS. The Brunauer-Emmett-Teller (BET) specific area, total pore volume, micropore volume and mesopore volume decreased all as the $TiO_2$ amounts coated on FAC increased, whereas the reverse was true for average pore diameter. $TiO_2$ coated onto FAC did not influence the adsorptional activity of FAC for the DMS input concentration of 0.5 ppm. The APA test of the hybrid material presented that the initial removal efficiencies of DMS were 93, 78, 71 and 57% for the flow rates of 0.5, 1.0, l.5 and 2.0 L/min, respectively, and they decreased somewhat 2 h after the experiment started and kept almost constant for the rest experimental period. Under this pseudo-equilibrium condition, the DMS removal efficiencies were 78, 58, 53 and 36% for the four flow rates, respectively. Meanwhile, there were no significant byproducts observed on the surfaces of the hybrid material. Consequently, this study suggests that, under the experimental conditions used in the present study, the hybrid material can be applied for DMS at residential environment levels without being interfered by any byproducts.

• Analytical Science and Technology
• /
• v.24 no.6
• /
• pp.421-428
• /
• 2011

In this study, headspace disk type monolithic material sorptive extraction (HS-MMSE) was developed, validated and applied to the analysis of volatile aroma compounds from vanilla perfume by gas chromatography -mass spectrometry (GC/MS). HS-MMSE uses monolithic material (MonoTrap) based on silica bonded with octadecyl silane (ODS) and activated carbon as a sorbent. Aroma compounds was adsorbed onto the MonoTrap in headspace and extracted by only 100 ${\mu}L$ of solvent. Total 12 volatile compounds from vanilla perfume were successfully analyzed using HS-MMSE. The influence of extractive parameters was investigated and optimized, using benzyl acetate, linalyl acetate, vanillin, ethyl vanillin as target compounds. Under the optimum condition, the limit of detection (S/N = 3) and the limit of quantification (S/N = 10) of proposed method for the target compounds were obtained within the range of 8.35~13.76 ng and 27.82~45.88 ng, respectively. The method showed good linearity with correlation coefficient more than 0.9888, satisfactory recovery and reproducibility. These results showed that HS-MMSE using disk type MonoTrap is a new promising technique for the analysis of volatile aroma compounds from vanilla perfume.

• Journal of the Korean Ceramic Society
• /
• v.42 no.3 s.274
• /
• pp.211-217
• /
• 2005

[ $Zn_{1-x}Co_{x}O$ (x=0-0.3) films were grown on Corning 7059 glasses by asymmetrical bipolar pulsed dc magnetron sputtering. The c-axis orientation along (002) plane was enhanced with increasing Co concentration. The $Zn_{1-x}Co_{x}O$ films are grown with fibrous grains of tight dome shape. The transmittance spectra measured from UV-visible showed that sp-d exchange interactions and typical d-d transitions become activated with increasing Co concentration. The electrical resistivity of $Zn_{1-x}Co_{x}O$ films increased with increasing Co concentration, especially it increased greatly at $30at\% Co. X-ray photoelectron spectroscopy and alternating gradient magnetometer analyses indicated that no Co metal cluster is formed and the ferromagnetic properties are exhibited. The low electrical resistivity and room temperature ferromagnetism of $Zn_{1-x}Co_{x}O$ thin films suggested the possibility of the application to Diluted Magnetic Semiconductors (DMSs).

• Journal of the Korean Ceramic Society
• /
• v.42 no.7 s.278
• /
• pp.475-482
• /
• 2005

Zn$_{l-x}$Co$_{x}$O (x = 0.05 - 0.20) films were grown on Coming 7059 glass by sol-gel process. A homogeneous and stable Zn$_{l-x}$Co$_{x}$O sol was prepared by dissolving zinc acetate dihydrate (Zn(CH$_{3}$COO)$_{2}$$\cdot$2H$_{2}$O), cobalt acetate tetrahydrate ((CH$_{3}$)$_{2}$$\cdot$CHOH) and aluminium chloride hexahydrate (AlCl$_{3}$ $\cdot$ 6H$_{2}$O) as solute in solution of isopropanol ((CH$_{3}$)$_{2}$$\cdot$CHOH) and monoethanolamine (MEA:H$_{2}$NCH$_{2}$CH$_{2}$OH). The films grown by spin coating method were postheated in air at 650°C for 1 h and annealed in the condition of vacuum (5 $\times$ 10$^{-6}$ Torr) at 300$^{\circ}C$ for 30 min and investigated the nature of c-axis preferred orientation and physical properties with different Co concentrations. Znl_xCOxO thin films with different Co concentrations were well oriented along the c-axis, but especially a highly c-axis oriented Zn$_{l-x}$Co$_{x}$O thin film was grown at 10 at$\%$ Co concentration. The transmittance spectra showed that Zn$_{l-x}$Co$_{x}$O thin films occur typical d-d transitions and sp-d exchange interaction became activated with increasing Co concentration. The electrical resistivity of the films at 10 at$\%$ Co had the lowest value due to the highest c-axis orientation. X-ray photoelectron spectroscopy and alternating gradient magnetometer analyses indicated that no Co metal cluster was formed, and the ferromagnetic properties appeared, respectively. The characteristics of the electrical resistivity and room temperature ferromagnetism of Zn$_{l-x}$Co$_{x}$O thin films suggested the possibility for the application to dilute magnetic semiconductors.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.5
• /
• pp.1088-1099
• /
• 2020

The purpose of this study was to confirm the possiblility of Zingiber mioga as a cosmetic material. For this we carried out biologically activated material characteristic evaluation about anti-oxidant, anti-inflammatory, wrinkle reduction effects using Zingiber mioga extract. To carry out this experiment, we extracted Zingiber mioga extract from Zingiber mioga flowers exract (ZMF) and Zingiber mioga leaves exract (ZML) with 70% ethanol. In order to evaluate the anti-inflammatory effect, we tested the toxicity and the hindrance activity to nitric oxide of samples using macrophages (RAW 264.7 cells). After we measured DPPH radical scavenging activity, ABTS+ radical scavenging activity and superoxide dismutase (SOD)-like activity of the Zingiber mioga extracts, we knew that they increased depending on their concentration. ZMF showed higher antioxidant activity than ZML after the measurement of ABTS+ radial scavenging activity and superoxide desmutase (SOD)-like activity. According to the measurement result of Nitric oxide inhibition activity we knew that ZMF reduced NO productions in a concentration-dependent manner. After the measurement of the biosynthesis quantity of pro-collagen type-1, we knew that its excellent effect appeared 110% or more at the concentration of 25 ㎍/ml. And at the same concentration, the result of the measurement of metalloprotease (MMP)-1 inhibition effect showed the 20% activation. In conclusion, ZMF is expected to be applied as a cosmetic material for wrinkle reduction. Zingiber mioga is believed to be used as a natural cosmetic material because it has been proven to have antioxidant, anti-inflammatory, and wrinkle-improving effects.

• Journal of Hydrogen and New Energy
• /
• v.22 no.3
• /
• pp.380-385
• /
• 2011

$MgH_2$ was synthesized by hydriding chemical vapor deposition (HCVD). In this study, we examined the hydrogen storage property of $MgH_2$ synthesized by HCVD. The results of pressure-composition-temperature (PCT) measurement showed that the HCVDed $MgH_2$ reversibly absorbed hydrogen as much as 6 wt%. Each hydrogenation rate was very greater than the conventional alloy methods. The reason was that the particle size made by HCVD was small as approximately 1 ${\mu}m$. The PCT of $MgH_2$ made by HCVD methode was similar to a commercial $MgH_2$. The ${\Delta}H$ and ${\Delta}S$ value are respectively -76.8 $kJ/mol{\cdot}H_2$ and -137.4 $kJ/mol{\cdot}H_2$. Mg made by HCVD methode was activated easily than commercial Mg. Also the initial reaction rate was faster than that of commercial $MgH_2$. 70% of the total storage were stored during 400s.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.11 no.2
• /
• pp.95-102
• /
• 2013

There was a study for biological characteristics, except for physico-chemical and mineralogical properties, on the natural bentonite that is considered as a buffer material for the high-level radioactive waste disposal site. A bentonite slurry that was prepared from a local 'Gyeongju bentonite' in Korea was incubated in a serum bottle with nutrient media over 1 week and its stepwise change was observed with time. From the activated bentonite in the nutrient media, we can find a certain change of both solid and liquid phases. Some dark and fine sulfides began to be generated from dissolved sulfate solution, and 4 species of sulfate-reducing bacteria (SRB) were identified as living cells in samples that were periodically taken and incubated. These results show that sulfate-reducing (or metal-reducing) bacteria are adhering and existing in the powder of bentonite, suggesting that there may be a potential occurrence of longterm biogeochemical effects in and around the bentonite buffer in underground anoxic environmental conditions.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.1
• /
• pp.1-9
• /
• 2009

Nowadays, Tra catfish fat is given attention as an appropriate material for biodiesel production in Vietnam. The aim of this work is to investigate the optimal conditions of refining biodiesel and recovering glycerin by the transesterification from Tra catfish fat using KOH catalyst. As our results, the yield of transesterification was achieved to 94.17% at $50^{\circ}C$ for 45 min with 6:1 molar ratio of methanol to fat in the presence of 0.8% KOH catalyst, and wherein the biodiesel was refined by washing with distilled water at $70^{\circ}C$ and dried in a microwave oven. The yield of raw glycerin recoveries from the transesterification process was 78.58%. The purity of raw glycerin was 84.14% by the conditions of neutralization state with $H_{3}PO_{4}$ solution (pH = 5), $70^{\circ}C$, and 60 min. Activated carbon (3.0 wt.%) was used for the bleaching process at $80^{\circ}C$ for 20 min. The biodiesel was obtained in accordance with for ASTM D 6751 (biodiesel standard). The ash and water of raw glycerins were 7.32 and 8.01%, respectively, and implied that the raw glycerin is very promising candidate to be used as a raw material for textile and cosmetic industries.

• The Journal of Korean Academy of Prosthodontics
• /
• v.40 no.3
• /
• pp.236-245
• /
• 2002

The acrylic resin was first introduced as denture base materials in 1937 and it is commonly used for denture base fabrication nowadays. Three different curing cycles (Conventional curing cycle, short curing cycle and long curing cycle) and three commercially available heat-activated acrylic resins (Vertex RS, Lucitone 199 and ProBase Hot) were investigated to find the curing cycle and material that showed the minimum shrinkage of the resin during polymerization process. A brass master mold was fabricated and duplicated by additional silicone impression material. Stone molds were made by pouring of type III dental stone (SILKY-ROCK YELLOW, Whip-Mix, Louisville, Kentucky). It was embedded in the flask. Strain gauge and thermocouple were embedded in the specimen. Strain gauge and thermocouple were connected to signal conditioning amplifier and data was recorded by pre-programmed software. The parameters ESmax (Maximum expansion strain), Sb (Strain measured just before deflasking procedure), Sa (Strain measured just after deflasking procedure) and Sf (Strain measured at the end of the experiment) were measured. ${\Delta}$S was calculated from Sb and Sa (${\Delta}$S=Sb-Sa). In the experiment concerned about materials, the parameters 90-ESmax (Maximum expansion strain measured during early 90 minutes of curing procedure), 180-ESmax (Maximum expansion strain measured from 90 minutes to 180 minutes), Sb, Sa, ${\Delta}$S and Sf were measured and the following conclusions were made. 1. The ESmax value of conventional curing cycle showed the largest value and the 180-ESmax value of Lucitone 199 showed the smallest value. 90-ESmax values showed no significant difference (p<0.05). 2. ${\Delta}$S values of conventional curing cycle showed the positive values. ${\Delta}$S values of short curing cycle and long curing cycle showed the negative values. All three materials cured by conventional curing cycle showed the positive values. 3. The Sf values of long curing cycle and ProBase Hot (cured by conventional curing cycle) showed the smallest values.

• The Korean Journal of Food And Nutrition
• /
• v.21 no.1
• /
• pp.35-42
• /
• 2008

To develop physiological functionality of Omija extracted with water was evaluated on antioxidative activity. Omija, high acid material with pH 3.6, contain $57.5{\pm}1.03%$ of moisture, and $18.8{\pm}0.12%$ of crude fat. This material have $12.6{\pm}0.04%$ of carbohydrate and $11.1{\pm}0.07%$ of crude protein as well, but ash and crude protein contents were found less than 10%. 10 mineral contents were also found, too; K and Ca showed the highest level, then Al, Mg, Na and Mn were followed. In composition amino acid contents, glutamic acid took the largest portion, $131.7{\pm}1.3$ mg/100 g, aspartic acid $51.5{\pm}0.6%$, and other composition amino acid under 50%. In case of free sugar contents, 7 types were found. Most of them were glucose and fructose. Total phenolic compounds showed the highest level, $2,862.6{\pm}31.7$ mg/100 g. $197.8{\pm}14.6$ mg/100 g of flavonoid and $225.6{\pm}18.2$ mg/100 g were included. In terms of electron donating ability, radical scavenging ability activated as the amount of Omija extract increased. In particular, Omija extract in 1,000 ${\mu}g/m{\ell}$ demonstrated almost similar electron donating ability, $72.4{\pm}0.21%$, to BHT. It was also found that antioxidant activities of electron donating ability, SOD-like ability, hydroxyl radical scavenging ability and nitrite scavenging ability were highly promoted as Omija extract concentration increased. The nitrite scavenging ability was significant when the extract belonged to strong acid region and doping concentrations increased.