• 한국전기전자재료학회논문지
• /
• 제24권5호
• /
• pp.359-363
• /
• 2011

To integrate the sensor driver and logic circuits, fabricating down scaled transistors has been main issue. At this research, short channel effects were analyzed after n channel polycrystalline silicon thin film transistor was fabricated at high temperature. As a result, on current, on/off current ratio and transconductance were increased but threshold voltage, electron mobility and s-slope were reduced with a decrease of channel length. When carriers that develop at grain boundary in activated polycrystalline silicon have no gate biased, on current was increased with punch through by drain current. Also, due to BJT effect (parallel bipolar effect) that developed under region of channel by increase of gate voltage on current was rapidly increased.

• Journal of Mechanical Science and Technology
• /
• 제19권3호
• /
• pp.802-810
• /
• 2005

Deformations of single crystals were studied using finite element analysis to investigate the localized modes and the orientation dependence of plastic deformation observed in single crystals. Investigation of mechanical properties of single crystals is closely related with the understanding of deformation processes in single crystals. Localized bands such as shear and kink were studied and the material and geometric characteristics that influence the formation of such localized bands were investigated. Orientation dependence of material behavior in NiAl single crystals was studied by rotating slip directions from 'hard' orientation. The maximum nominal compressed stress in NiAl single crystals was widely ranged depending on the misalignment from 'hard' orientation. As the compression axis was set closer to 'hard' orientation, the maximum nominal compressed stress was rapidly increased and made <100> slips difficult to activate. Therefore, non-<100> slips will be activated instead of <100> slips for 'hard' orientation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.848-850
• /
• 2001

In this work, we investigated on the white-colored ribbon fiber synthesized from GaN powder. We convinced the formation of monoclinic phase $\beta$-Ga$_2$O$_3$from the X-ray diffraction pattern on ribbon fiber. The 10 K PL spectrum consisted with the strong emission band caused by self-activated optical center at 3.464 eV with the full-width at half maximum of 48 meV and the impurity related emission bands. Through this work, the optical properties and the electrical conductivity of $\beta$-Ga$_2$O$_3$, it will be useful for the fabrication of optoelctronic devices operating in visible spectrum region.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.851-854
• /
• 2001

Europium-activated Ga$_2$O$_3$powders were prepared by modified "Pechini method" from mixed aqueous solutions of gallium nitrate, europium nitrate, ethylene glycol and citric acid. The formation process and structure of the phosphor powders were investigated by means of TG/DTA, XRD and SEM. It has been found that the phosphor powders were amorphous up to 50$0^{\circ}C$ and changed into crystalline $\beta$-Ga$_2$O$_3$phase above $600^{\circ}C$. The resulting nano-sized powders were obtained. Red luminescence in emission spectra were observed at room temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.621-624
• /
• 2002

Lanthanum nickel oxide$(LaNiO_3)$ powders have been prepared via a mechanochemical processing without any additional heat treatment. When a mixed lanthanum and nickel oxide was mechanically activated for 6 hours with 450 rpm, a stable and single phase perovskite powder was successfully synthesized and its crystallite size of about 90 nm is calculated by using the Scherrer equation.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.64-69
• /
• 1999

Slags are by-products of the metallurgical industry. The most important slag from the standpoint of the quantity used as building material is iron blastfurnace slag. Slags are either crystalline stable solid used as aggregates or glassy material used as hydraulic binder. Slag cements are low heat of hydration cements. Slags react more slowly with than portland cement but they can be activated chemically. Activatiors can be either alkaline activators such as soda, lime, sodium carbonate, sodium silicate or sulphate activators such as calcium sulphate or phosphogypsum. So, in this study slaked lime was used as an activator that the compressive strength of this modified cement(M1 type) is high range in early age. And initial setting time of M1 type cement was shorter than conventional cements.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.113-114
• /
• 2008

Conventional furnace annealing (CFA) for activating Mg-doped p-type GaN films had been performed in pure $N_2$ ambient. All sample activated the same gas ambient. The annealing process change temperature: the first process is performed at $550^{\circ}C$ for 10 min. but, the first process is the same bulk. From second to five process increase activation temperature to change $50^{\circ}C$ and annealing time keeping for 10 min. It is found that the samples characteristic measure hall measurement. Similar results were also evidenced by photoluminescence (PL) measurement.

• 한국정밀공학회지
• /
• 제25권3호
• /
• pp.126-133
• /
• 2008

The main objective of the present study is to achieve linear temperature distribution of cooling surface of plunger. K type thermocouples are attached at the surface of plunger to measure temperature. Nozzle and insulating material are inserted in the pin hole of the plunger for this study. Cooling water flow enters at one nozzle and leaves at three nozzles. Flow through nozzle can be activated in the pin hole, temperature of hot point around hole is decreased. Meanwhile, insulating material blocks off heat transfer, temperature of cold point around hole is increased. By combination of nozzle and insulation, heat transfer of hole is controlled effectively, as result its, temperature of plunger surface shows linear temperature distribution.

• 환경위생공학
• /
• 제10권2호
• /
• pp.13-22
• /
• 1995

Most of small- scale livestock facility have difficulties to treat organic wastewater by activated sludge process as distinguished feces and urine. The organic wastewater discharged have characteristics of slurry, high concentration of BOD, 55 etc. This study was performed to estimate suitable condition for the application of packing materials, air flow, pollutant load and so on as important parameter to treat organic wastewater by thermopile oxlc process. As a result obtained at this experiments the most suitable condition for BOD load, air flow indicate 3.0kg · m$^{-3}$ day$^{-1}$,50 ∼ 100L· min$^{-1}$ m$^{-3}$, respectively, and we knew that it was necessary to add waste contained high calories to degrade about 80% of pollutant among waste- water. It showed that plastic material can be used as packing media because it can be provided as inhabitation for microorganism owing to intensity of material and characteristic of keeping moisture.

• 소성∙가공
• /
• 제8권3호
• /
• pp.253-253
• /
• 1999

Dense WC-10 vol.%Co composite was simultaneously synthesized with field-activated and pressure-assisted combustion synthesis (FAPACS) within several minutes in one step from elemental powders of W, C and Co. Combustion synthesis was carried out under the combined effect of an electric field and mechanical pressure. Under the application of 60MPa pressure and 3000A current on the reactants, the relative density of WC-10 vol.%Co composite was 98.4%. The fracture toughness and hardness of WC-10 vol.%Co were 8.6 MPa·$m^{1/2}$ and 1900 kg/mm², respectively.