• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.237-240
• /
• 2000

본 연구에서는 한국 동해 대륙붕 해역에서의 주요 해양현상인 수직 수온구조의 단기변동, 수온전선, 그리고 내부파의 변동을 분석하고 이들 변화에 따른 음파의 음장변화를 고찰하였다. 한국 동해항 근해에서 수온의 수직적 변화는 계절적인 변화 이외에 약 2주간의 짧은 기간에도 매우 극적인 변화가 존재함이 실측자료를 통해 밝혀졌다. 1999년 관측된 CTD 자료를 바탕으로 음장 변화를 살펴본 결과 주파수 1kHz, 음원수심 $30{\cal}m$ 인 경우 수신기 수심에 따라 최소 3dB, 최대 10dB까지 차이를 가져올 수 있음을 알 수 있었다. 한국 동해에서 연안과 외해 사이에는 수온전선이 매우 자주 발달하며 여름에 가장 강한 것으로 알려져 있다. 동해항 근해에는 대표적인 수괴인 대마난류수와 북한한류수가 공존하며 이들의 상대적인 세력 변화 때문에 수은(음속)이 거리에 따라 급격하게 변하는 수온전선이 발달할 수 있다. 저주파수 대역 (200Hz)에 대한 간단한 시뮬레이션 결과는 수온전선이 정상적인 분포에 비해서 거리에 따라 7dB 정도의 큰 전파손실을 초래할 수 있음을 보인다. 한국 동해 연안에도 내부파가 존재한다는 사실이 최근 3년간의 연구 결과 밝혀졌다. 내부파는 외해에서 발생하여 대륙단을 거쳐 대륙붕으로 진행해 오면서 내부파 군 (Packets)으로 분산된다. 수직적 변화가 전체 수층의 $14\%$를 차지하는 간단한 형태의 내부파를 가정하여 음장변화를 시물레이션 한 결과 주파수 1 kHz, 음원수심 $20{\cal}m$인 경우 내부파는 수렴구역 형성을 현저하게 방해하여 최대 5dB까지의 차이를 유발하였다. 추후 이에 대한 연구는 내부파 전체의 시,공간적 분포 특성이 구체적으로 규명되면 보다 정확한 음장변화 추정이 이뤄져야 할 것으로 보인다. 또한 내부파와 음파의 상대적인 진행 방향에 따라 음장변화가 크게 다를 것이 예상되므로 이를 규명하기 위해서는 궁극적으로 3차원적인 음장분포 연구가 필요하다. 음향센서를 해저면에 매설할 경우 수충의 수온변화와 센서 주변의 수온변화 사이에는 어느 정도의 시간지연이 존재하게 되므로 이에 대한 영향을 규명하는 것도 센서의 성능예측을 위해서 필요하리라 사료된다.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.4
• /
• pp.29-37
• /
• 1995

A resonant frequency of piezoelectric transducer depends remarkably on the electric impedance connected to the vibrator. In this paper, using this effect of frequency controllable two layered PZT ultrasonic transducer is designed and its acoustic characteristics are analyzed by a new transmission model equivalent circuit. The theoretical and the experimental results of the electric impedance effect on the resonant frequency variation were compared and both results showed a good consistency each other. The resonant frequency has been controlled continuously in the wide frequency range of 180kHz~580kHz and the effective attenuations were less than 7dB in the frequency range of 330kHz~470kHz.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.11a
• /
• pp.13-18
• /
• 2009

Flight vehicles such as wheel wells and bomb bays have many cavities. The flow around a cavity is characterized as an unsteady flow because of the formation and dissipation of vortices brought about by the interaction between the free stream shear layer and the internal flow of the cavity. The resonance phenomena can damage the structures around the cavity and negatively affect the aerodynamic performance and stability of the vehicle. In this study, a numerical analysis was performed for the cavity flows using the unsteady compressible three-dimensional Reynolds-Averaged Navier-Stokes (RANS) equation with Wilcox's turbulence model. The Message Passing Interface (MPI) parallelized code was used for the calculations by PC-cluster. The cavity has aspect ratios (L/D) of 2.5 ~ 7.5 with width ratios (W/D) of 2 ~ 4. The Mach and Reynolds numbers are 0.4 ~ 0.6 and $1.6{\times}106$, respectively. The occurrence of oscillation is observed in the "shear layer and transient mode" with a feedback mechanism. Based on the Sound Pressure Level (SPL) analysis of the pressure variation at the cavity trailing edge, the dominant frequencies are analyzed and compared with the results of Rossiter's formula. The dominant frequencies are very similar to the result of Rossiter's formula and other experimental data in the low aspect ratio cavity (L/D = ~ 4.5). In the large aspect ratio cavity, however, there are other low dominant frequencies due to the leading edge shear layer with the dominant frequencies of the feedback mechanism. The characteristics of the acoustic wave propagation are analyzed using the Correlation of Pressure Distribution (CPD).

• Journal of the Korean Institute of Gas
• /
• v.9 no.3 s.28
• /
• pp.1-8
• /
• 2005

We studied on the nondestructive evaluation of the elastic wave signals of locally wall thinned straight pipe. Wavelet transform was applied for the time-frequency analysis of waveforms obtained by fracture wave detector due to the dropping steel ball. The time-frequency analysis provides time variation of each frequency component involved in a waveform, which makes it possible to evaluate the shape of local wall thinning at each frequency. In this study, comparison by wavelet transform of the AE signals and monotonic bending tests without internal pressure are conducted on 1.91 inch diameter full-scale carbon steel pipe specimens. As the results of tests, fracture behaviors could be shown by the characteristic of mechanical strength of locally wall thinned pipes and the waveforms could be evaluated for the integrity insurance of the piping system according to the length and depth range of the deffeted shape pipes in the real field.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.2
• /
• pp.82-90
• /
• 2011

The small precision spindle motors in the high value-added products including the visible home appliances such as DLP projector require not only the energy conversion devices but also high efficiency, low vibration and sound operation. However, the spindle motors using the conventional ball bearing and sintered porous metal bearing have following problems, respectively: the vibration by the irregularity of balls and the short motor life cycle by the ball's abrasion and higher sound noises by dry contact between shaft and sleeve. In this paper, it is proposed that the spindle motor with a fluid dynamic bearing is suitable for the motor to drive the color wheel of the DLP(digital lightening processor) in the visible home appliances. The proposed spindle motor is composed of the fluid dynamic bearing with both the radial force and the thrust force. The fluid dynamic bearing is solved by the finite element analysis of the mechanical field with the Reynolds equations. The magnetic part of spindle motor, which is a type of Brushless DC Motor, is designed by the electro-magnetic field analysis coupled with the Maxwell equation. And the load capacity and the friction loss of fluid dynamic bearing are analyzed to bearing clearance variation by the fabrication error in designed motor. The design of the proposed motor is implemented by the load torque caused by the eccentricity and the unbalance of the fluid dynamic bearing when the motors are fabricated in error. The prototype of the motor with the fluid dynamic bearing is manufactured, and experiment results show the vibration, sound, and phase current at no load and color wheel load of the motors in comparison. The high performance characteristics with the low vibration, the low acoustic noise and the optimal mechanical structure are verified by the experimental results.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.12
• /
• pp.93-102
• /
• 1998

In noisy environments, human speech productions are influenced by noises(Lombard effect), and speech signals are contaminated. These distortions dramatically reduce the performance of speech recognition systems. This paper proposes a method of the Lombard effect compensation and noise suppression in order to improve speech recognition performance in noise environments. To estimate the intensity of the Lombard effect which is a nonlinear distortion depending on the ambient noise levels, speakers, and phonetic units, we formulate the measure of the Lombard effect level based on the acoustic speech signal, and the measure is used to compensate the Lombard effect. The distortions of speech under noisy environments are cancelled out as follows. First, spectral subtraction and band-pass filtering are used to cancel out noise. Second, energy nomalization is proposed to cancel out the variation of vocal intensity by the Lombard effect. Finally, the Lombard effect level controls the transform which converts Lombard speech cepstrum to clean speech cepstrum. The proposed method was validated on 50 korean word recognition. Average recognition rates were 82.6%, 95.7%, 97.6% with the proposed method, while 46.3%, 75.5%, 87.4% without any compensation at SNR 0, 10, 20 dB, respectively.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.5
• /
• pp.63-73
• /
• 1995

The conventional acoustic sounds can be synthesized by Frequency Modulation which includes the variation of frequency, amplitude, and modulation index. In this paper the number of variable synthesis parameters are limited to easily implement the existing two carrier FM algorithm by hardware. The DSP(Digital Signal Processor), which is able to carry out the modified algorithm and synthesize 16 sounds at a time, is designed with $0.8{\mu}m$ standard sells. The DSP which can synthesize 2 sounds at a time is implemented by ASIC emulator to examine the sound quality of the designed DSP. Through the objective and subjective estimation, it is confirmed that the sounds of many instruments from the implemented DSP are very closed to their real sound. Finally the designed DSP is layouted and simulated by VLSI desgn tool. According to the simulation, the designed DSP has the sufficiently fast speed for synthesizing 16 sounds at a time.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.8
• /
• pp.78-83
• /
• 2000

Passive sonar system is designed to classify the underwater targets by analyzing and comparing the various acoustic characteristics such as signal strength, bandwidth, number of tonals and relationship of tonals from the extracted tonals and frequency lines. First of all the precise detection and extraction of signal frequency lines is of particular importance for enhancing the reliability of target classification. But, the narrowband frequency lines which are the line formed in spectrogram by a tonal of constant frequency in each frame can be detected weakly or discontinuously because of the variation of signal strength and transmission loss in the sea. Also, it is very difficult to detect and extract precisely the signal frequency lines by the complexity of impulsive ambient noise and signal components. In this paper, the automatic detection and extraction method that can detect and extract the signal components of frequency tines precisely are proposed. The proposed method can be applied under the bad conditions with weak signal strength and high ambient noise. It is confirmed by the simulation using real underwater target data.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.5
• /
• pp.765-771
• /
• 2001

Elastic-plastic fracture toughness JIC can be used a s an effective design criterion in elastic-plastic fracture mechanics. Among the JIC test methods approved by ASTM, unloading compliance method was used in this study. In order to examine the relationship between fracture behavior of JIC test and AE signals, the post processing of AE signals has been carried out by Short Time Fourier Transform(STFT), one of the time-frequency analysis methods. The objective of this study is to evaluate the application of characterization of AE signals for unloading compliance method of JIC test. As a result of time-frequency analysis, we could extract the AE from the raw signal and analyze the frequencies in AE signal at the same time. AE signal generated by elastic-plastic fracture of material has some different aspects at elastic and plastic ranges, or the first portion of crack growth by fracture. First of all, increased energy recorded and detected by using AE count method increase rapidly from the start of ductile fracture. The variation of main frequency range with time-frequency analysis method could be confirmed. We could know fracture behavior of interior material by examination AE characteristics generated in real-time when elastic-plastic fracture occurred in material under loading.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.3
• /
• pp.235-241
• /
• 2009

Composite wood materials are very sensitive to water and inspection without any coupling medium of a liquid is really needed to wood materials due to the permeation of coupling medium such as water. However, air-coupled ultrasound has obvious advantages over water-coupled experimentation compared with conventional C-scanner. In this work, it is desirable to perform contact-less nondestructive evaluation to assess wood material homogeneity. A wood material was nondestructively characterized with non-contact and contact modes to measure ultrasonic velocity using automated data acquisition software. We have utilized a proposed peak-delay measurement method. Also through transmission mode was performed because of the main limitation for air-coupled transducers, which is the acoustic impedance mismatch between most materials and air. The variation of ultrasonic velocity was found to be somewhat difference due to air-coupled limitations over conventional scan images. However, conventional C-scan images are well agreed with increasing the resin-infiltrated time as expected. Finally, we have developed a measurement system of an ultrasonic velocity based on data acquisition software for obtaining ultrasonic quantitative data for correlation with C-scan images.