• 한국소음진동공학회논문집
• /
• 제23권5호
• /
• pp.456-462
• /
• 2013

Eco-friendly material applied to building would be one of the materials which is must developed for global environmental conservation and reduction of carbon dioxide. For development of eco-friendly material, a cellulose absorber has been developed with waste paper through adjustment of various mix proportions. The developed cellulose absorber has been tested for its acoustic properties such as absorption coefficient and dynamic stiffness. The absorption coefficient was evaluated by developing six samples and using impedance tube and reverberation chamber. As a result of the evaluation, 0.64(NRC) was secured in absorption coefficient and 4.7 $MN/m^3$ was indicated in dynamic stiffness. Also, for practical use of developed absorbers as inner heartwood in drywall, comparison test of sound reduction index was performed with existing glass wool absorbers and constructed drywall of gypsum board. The results have shown 55 dB(Rw) of sound reduction index in glass-wool wall and 46 dB(Rw) in cellulose.

• Composites Research
• /
• 제13권3호
• /
• pp.1-8
• /
• 2000

Excellent environmental durability and handy installation procedure as well as high specific strength and stiffness have introduced fiber-reinforced polymeric composite materials into the civil and architectural engineering field. This study presents the considerably enhanced strength characteristics of the mortal beams by being reinforced with epoxy-bonded carbon fiber sheets(CFS). Three point bending and Charpy impact tests were performed on both of bare and reinforced mortar specimens. The influences of length, and the number of reinforcing plies were investigated. Strength reduction due to pre-existent notch was lessened dramatically. The acoustic emission(AE) measurement revealed the progressive damage process in reinforced specimens.

• 소음진동
• /
• 제1권2호
• /
• pp.141-147
• /
• 1991

A vectorial approach is used to reduce the objectionable booming noise in the vehicle interior cabin. After identifying the structural transmisson paths, the structural-acoustic transfer functions are evaluated at those mounting positions. Using the measured deformations in the mounting elements and multiplying them with each dynamic stiffness value one can easily get the dynamic input forces acting on the mounting elements. By summing all the contributors vectorially, most important contributor or transmission path can be determined. According to the experimental information, devised countermeasures are applied to a development car and good results are obtained.

• 한국음향학회지
• /
• 제25권4호
• /
• pp.164-171
• /
• 2006

임의의 등방성재료에 대한 종파, 횡파 및 누설표면파의 음속을 알면 해석적으로 그 재료의 탄성정수와 밀도를 산출할 수 있다. 종래, 그 음속들은 각각 다른 진동모드를 갖는 세 개의 초음파 트랜스듀서에 의해 측정되어져 왔다. 본 연구에서는 하나의 트랜스듀서에 의해 그 세 가지 파의 개략적인 음속을 동시에 측정하기위한 전극분할형 PVDF 직선집속 초음파 트랜스듀서를 새로이 제안하고, 설계, 제작하였다. 그리고 그것에 의한 각 파의 음속측정 방법을 확립한 후, 용융석영 등 몇몇 등방성재료에 적용하였다. 또한, 측정된 각 파의 음속을 이용하여 탄성 강성정수 및 밀도를 산출하고, 각 값들의 오차를 검토하였는데, 얻어진 값들은 문헌치와 비교적 잘 일치함을 알 수 있었다.

• Composites Research
• /
• 제17권3호
• /
• pp.15-22
• /
• 2004

위성 발사체의 추진 기관에 의한 음향 하중은 이륙 시 작용하는 주요한 동적 하중 중 하나로서, 이에 의한 위성이나 탑재물의 파손이 보고되고 있다. 위성이나 탑재물에 작용하는 음향 하중의 강토를 저감하기 위해서는 노즈 페어링의 구조 설계 시 차음 성능을 고려한 설계가 필요하다. 특히 복합재 구조의 경우 금속재 구조에 비해 비강성이 커서 음향 하중의 차음 측면에서는 불리하다. 본 논문에서는 위성 발사체의 노즈 페어링용 복합재 평판의 차음 특성을 살펴보았다. 노즈 페어링 구조로 사용 가능한 4종의 복합재 구조에 대하여 무한판 이론 및 통계적 에너지 해석법(SEA)을 이용하여 차음 성능을 평가하였다. 해석 결과를 토대로 두 종류의 복합재 평판을 제작하여 이에 대한 차음 성능을 측정하고 예측치와 비교를 수행하였다. 이를 바탕으로 무게 대비 차음 성능이 우수한 노즈 페어링용 복합재 구조를 선정할 수 있었다.

• Composites Research
• /
• 제35권2호
• /
• pp.61-68
• /
• 2022

복합재료는 비강도, 비강성 및 내부식성 등이 우수하여 항공우주산업뿐만 아니라 다양한 산업에서 사용되고 있다. 그러나 복합재료는 충격에 취약하고 이러한 충격은 복합 재료 내부의 균열 형성과 균열 성장으로 이어져 구조 파단의 원인이 된다. 본 논문에서는 음향 방출 신호 및 유한요소해석(Finite element analysis, FEA)을 이용하여 복합재 적층판의 Mode I 파괴 모드의 특성을 분석하였다. DCB 시험은 탄소/에폭시 적층판의 Mode I 파괴 특성을 분석하기 위하여 수행되었고 시편의 파괴에 의해서 발생되는 탄성파를 측정하기 위하여 시편에 음향 방출 센서를 부착하였다. 누적 음향 방출 에너지와 균열 선단 위치의 관계를 이용하여 시편의 파괴 인성(Fracture toughness, G_I)을 계산하였다. 계산된 파괴 인성 값을 유한요소모델에 적용하여 해석을 수행하였고 하중-변위 곡선 및 균열 길이-변위 곡선을 통하여 DCB 시험 결과와 비교/분석하였다. 유한요소해석 및 DCB 시험의 결과가 잘 일치함을 보였다.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제11권3호
• /
• pp.105-113
• /
• 2003

This study developed a practical two-microphone impedance tube method to measure the sound transmission loss of sound isolation materials without the use of an expensive reverberation room or an acoustic intensity probe. In order to evaluate the validation and applicability of the two-microphone impedance tube method, sound transmission losses for several sound isolation materials with different surface density and bending stiffness were measured, and the measured values were compared with the results from the reverberation room method and the theory. From the experimental results, it was found that the accuracy of sound transmission loss obtained by the impedance tube method depends upon the diameter size of the impedance tube (i.e., tested sample size). For sound isolation materials having relatively large bending stiffness such as acryl, wood, and aluminum plates, it was found that the impedance tube method proposed by this study was not valid to measure the sound transmission loss. On the other hand, for sound isolation materials having relatively small bending stiffness such as rubber, polyvinyl, and asphalt sheets, the comparisons of transmission loss between the results from the impedance tube method and the theory showed a good agreement within the range of the frequencies satisfying the normal incidence mass law. Therefore, the two-microphone impedance tube method proposed by this study can be an effective measurement method to evaluate the sound transmission loss for soft sound isolation sheets having relatively small bending stiffness.

• International Journal of Automotive Technology
• /
• 제4권1호
• /
• pp.21-30
• /
• 2003

In this paper a systematic test procedure for evaluation of road-induced noise of a vehicle and guidelines for each test are presented. Also, a practical application of the test procedure to a small SUV is presented. According to the test procedure, all the tests were performed to evaluate road-induced booming noise that is in low frequency range. First of all the information on characteristics of road-induced noise was obtained through baseline test. Coupling effects between body structure and acoustic cavity of a compartment were obtained by means of modal tests for a structure and an acoustic cavity. Local stiffness of joint areas between chassis system and car-body was determined by test for measurement of input point inertance. Noise sensitivities of body joints to operational forces were obtained through test for measurement of noise transfer functions. Operational deflection shapes made us analyze behaviors of chassis system under running condition and then find sources of noise due to resonance of the chassis system. Finally, Principal Component Analysis and Transfer Path Analysis were utilized to investigate main paths of road-induced noise. In order to evaluate road-induced booming noise exactly, all of tests mentioned above should be performed systematically.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.111-111
• /
• 2009

In this work, we discuss simulation of surface acoustic wave device using Comsol Multiphysics. The structure SAW device based on piezoelectric thin film aluminum-nitride (AlN) on silicon was simulated. Some parameters of SAW device such as surface velocity, displacement of piezoelectric thin film were evaluated by software. Many modes and shapes of wave are also discussed in this paper. For evaluation physical parameters of AlN piezoelectric layer, the SAW resonator was modeled and simulation results were also compared with experiment results. we simulated arid evaluated the surface Rayleigh wave of AlN thin film on silicon substrate. Results simulation and experiment showed the surface velocity of AlN thin film was about 5200 m/s and shape of surface wave was also displayed. This paper has also proposed as method to study SAW characteristic of piezoelectric thin film and found out measurement values accurately of film such as stiffness matrix, piezoelectric matrix. These values are very important in calculation and design SAW device or MEMS device based on AlN piezoelectric layer.

• 한국소음진동공학회논문집
• /
• 제14권11호
• /
• pp.1066-1074
• /
• 2004

A vibration isolation system for a large reverberation chamber (1,228 $m^3$ and 1,000 ton) has been installed and verified. The reverberation chamber generates loud noise and induces high level of vibration while performing spacecraft acoustic reliability tests. The isolation system prevents vibration transfer from the chamber to the enclosure buildings. This paper describes design process and commissioning experiments of the system. Design criteria have been derived from rigid body model of the chamber. The stiffness of neoprene pads has been selected by employing finite element analysis of the reverberant chamber and isolation system. A total of 21 neoprene pads have been installed between the chamber and supporting Pedestals. A sand bag of 800kg was dropped on the chamber floor to measure the natural frequency of the isolation system. While 136.9 dB noise is generated in the chamber, absolute transmissibility of the isolation system has been measured. The measured natural frequency of the chamber is 10.2Hz, which is 80% of the predicted value. Overall transmissibility at working frequency range (25∼10.000 Hz) is less than -12.4 dB.