• Progress in Medical Physics
• /
• v.10 no.2
• /
• pp.103-114
• /
• 1999

In this study, as a preliminary study for developing a full 3D photon dose calculation algorithm, We developed 2.5D photon dose calculation algorithm by extending 2D calculation algorithm to allow non-coplanar configurations of photon beams. For this purpose, we defined the 3d patient coordinate system and the 3d beam coordinate system, which are appropriate to 3d treatment planning and dose calculation. and then, calculate a transformation matrix between them. For dose calculation, we extended 2d "Clarkson-Cunningham" model to 3d one, which can calculate wedge fields as well as regular and irregular fields on arbitrary plane. The simple Batho's power-law method was implemented as an inhomogeneity correction. We evaluated the accuracy of our dose model following procedures of AAPM TG#23; radiation treatment planning dosimetry verifications for 4MV of Varian Clinac-4. As results, PDDs (percent depth dose) of cubic fields, the accuracy of calculation are within 1% except buildup region, and $\pm$3% for irregular fields and wedge fields. And for 45$^{\circ}$ oblique incident beam, the deviations between measurements and calculations are within $\pm$4%. In the case of inhomogeneity correction, the calculation underestimate 7% at the lung/water boundary and overestimate 3% at the bone/water boundary. At the conclusions, we found out our model can predict dose with 5% accuracy at the general condition. we expect our model can be used as a tool for educational and research purpose.. purpose..

• Nuclear Engineering and Technology
• /
• v.55 no.11
• /
• pp.4102-4111
• /
• 2023

In order to better perform thermal hydraulic calculation and analysis of supercritical water reactor, based on the experimental data of supercritical water, the model training and predictive analysis of the heat transfer coefficient of supercritical water were carried out by using the support vector machine (SVM) algorithm. The changes in the prediction accuracy of the supercritical water heat transfer coefficient are analyzed by the changes of the regularization penalty parameter C, the slack variable epsilon and the Gaussian kernel function parameter gamma. The predicted value of the SVM model obtained after parameter optimization and the actual experimental test data are analyzed for data verification. The research results show that: the normalization of the data has a great influence on the prediction results. The slack variable has a relatively small influence on the accuracy change range of the predicted heat transfer coefficient. The change of gamma has the greatest impact on the accuracy of the heat transfer coefficient. Compared with the calculation results of traditional empirical formula methods, the trained algorithm model using SVM has smaller average error and standard deviations. Using the SVM trained algorithm model, the heat transfer coefficient of supercritical water can be effectively predicted and analyzed.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.5 no.1
• /
• pp.49-58
• /
• 1987

The use of digital terrain model has been enlarged in calculating the earthwork due to the development of aerial photogrammetry. The calculation of earthwork plays a major role in plan or design of many civil engineering projects, and thus it has become very important to advance the accuracy of earthwork calculation. In this study, I have made an analysis of influences which DTM makes on the height accuracy of data ; on the basis of the analysis, we can develop the predictive model formula of profile shape coefficients by which the accuracy of earthwork can he preestimated in practical design according to data density of terrain, making thereby good contribution to the calculation of both earthwork amount and its expenses. This study shows that the accuracy of earthwork is more affected by the distances of cross-sections than by data density and that the effects by the standard errors of height decrease in proportion as the distances of cross-sections are great It also shows that when the prediction model formula of profile shape coefficients is applied to ordinary cases, the differences between the predicted earthwork errors and the errors by ordinary est imation are at 0.8374~3.1437$cm^3$/m, on flat terrain and 1.5628~6.967$cm^3$/m, on mountainous terrain-so little as to be ignored ; thus it can be safely ascertained that the accurate earthwork errors can be predicted applying the prediction model formula made in this study.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.91-99
• /
• 2017

In order to meet the thermal performance analysis accuracy requirements of high density permanent magnet synchronous motor (PMSM), a method of multi physical domain coupling thermal analysis based on control circuit, electromagnetic and thermal is presented. The circuit, electromagnetic, fluid, temperature and other physical domain are integrated and the temperature rise calculation method that considers the harmonic loss on the frequency conversion control as well as the loss non-uniformly distributed and directly mapped to the temperature field is closer to the actual situation. The key is to obtain the motor parameters, the realization of the vector control circuit and the accurate calculation and mapping of the loss. Taking a 48 slots 8 poles high density PMSM as an example, the temperature rise distribution of the key components is simulated, and the experimental platform is built. The temperature of the key components of the prototype machine is tested, which is in agreement with the simulation results. The validity and accuracy of the multi physical domain coupling thermal analysis method are verified.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1387-1395
• /
• 2016

A method for the identification of mechanical parameters based on integral calculation is presented. Both the moment of inertia and the friction constant are identified by the method developed here, which is based on well-known mechanical differential equations. The mechanical system under test is excited according to a pre-determined low-frequency sinusoidal motion, minimizing the distortion, and increasing the accuracy of the results. The parameters are identified using integral calculation, increasing the robustness of the results against measurement noise. Experimental data are supported by simulation, confirming the effectiveness of the proposed technique. The performance improvements shown here are of use in the design of speed and position controllers and observers. Owing to its simplicity, this method can be readily applied to commercial inverter products.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.26 no.3
• /
• pp.162-177
• /
• 1998

Conentionally, LS factor for the USLE suggested by Wischmeier has been computed manually on topographic maps based on one dimensional approach. But outcomes of the equation could be severely affected by the convergence and divergence of surface runoff at complex terrains. Thus the objective of this research are to develop a method to automatically compute LS factor based on the multiple flow algorithm, and to test the accuracy of this method by comparing outcomes of this method to previous measurements or estimations of soil erosion. The program for the automatic calculation of LS factor was developed by utilizing Fox Pro 4.5, and outcomes of the program is designed to input to IDRISI. The accuracy test of LS factor was carried out by comparing the actual measurements of soil loss at two test sites in and around of Suwon. The calculated volume of soil erosion at Buju mountain, Mokpo, was also compared to the outcome of a previous research based on the LS factor calculated by the conventional onedimensional approach. The outcomes of this research are as follows. First, the computed L based on the multiple flow algorithm for concae slopes are greater than those of convex slopes,. Second, the estimated soil loss based on this method at the test site in Mokpo is much greater than the outcomes based on the conventional one-dimensional approach. It can e concluded that the application of this automatic calculation method of LS factor can improve the accuracy of USLE and facilitate soil erosion prevention methods.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2007.04a
• /
• pp.813-818
• /
• 2007

A method for automatic check of omitted design item in structural calculation document of steel box bridges is proposed. A method for automatic check of omitted design item in structural calculation document of steel box bridges is proposed. Information processing for the proposed method is divided into two steps: automatic generation of document structure in XML Schema Definition (XSD) format and extract omitted design items by using the XML Schema matching technique. The automatic omitted element filter is developed on the basis of the proposed method, and the accuracy of the developed module is examined with case study subjected to existing structural calculation document samples.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.188-192
• /
• 2000

An analysjs model for calculation the motion accuarcy of double sides hydrostatic table is proposed in thn paper. For the analysis of motion accuracy, profiles of each rails are assumed as periodic function, and represented using Fourier coefficients. Variahon of bearing clearance is represented as the vanation of linear, angular displacement of table and profiles of rails. Motion accuracy is calculated in the basis of finite element analysis on the pressure dutributmn of table. In order to improve calculating time in the analysis of motion accuracy, The proposed modeling method converts double sides table to single side table equivalently Results by the proposed method 1s compared with directly caculated results mdyhcally, and also compared wlth experimental results. From the theoretical and experimental analysis, it is confirmed that the proposed modeling mothod is very effective to analyze the motion accuracy of dauble sides hydrostatic table.

• Nuclear Engineering and Technology
• /
• v.45 no.6
• /
• pp.753-758
• /
• 2013

A new method of calculating sensitivity coefficients of core characteristics relative to infinite-dilution cross sections has been developed. Conventional sensitivity coefficients are evaluated for the changes of effective cross sections which are dependent on individual models of core and cell. Therefore a correction has been derived to the conventional sensitivity coefficients based on the perturbation theory. The accuracy of the present method has been verified by comparing numerical results of sensitivity coefficients with a reference Monte-Carlo method.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.11B no.4
• /
• pp.137-145
• /
• 2001

The magnetic force calculation methods, the Maxwell＇s stress tensor method, virtual work method, and nodal force method, are reviewed and the equivalence of them are theoretically proved. The methods are applied to the magnetic force calculation of 2D linear and nonlinear problems, and 3D nonlinear problem. As the results, the convergence of the methods as the number of elements increases, accuracy of the methods, and integral path dependence of the methods are discussed. Finally some recommendations on the usage of the methods, including the determination of the integral path, are given.