• Journal of Ocean Engineering and Technology
• /
• v.31 no.1
• /
• pp.69-79
• /
• 2017

This paper presents the operations of a multi-beam echo sounder (MBES) installed on the deep-sea remotely operated vehicle (ROV) Hemire. Hemire explored hydrothermal vents in the Forecast volcano located near the Mariana Trench in March of in 2006. During these explorations, we acquired profiling points on the routes of the vehicle using the MBES. Information on the position, depth, and attitude of the ROV are essential to obtain higher accuracy for the profiling quality. However, the MBES installed on Hemire does not have its own position and depth sensors. Although it has attitude sensors for roll, pitch, and heading, the specifications of these sensors were not clear. Therefore, we had to merge the high-performance sensor data for the motion and position obtained from Hemire into the profiling data of the MBES. Then, we could properly convert the profiling points with respect to the Earth-fixed coordinates. This paper describes the integration of the MBES with Hemire, as well as the coordinate conversion between them. Bathymetric maps near the summit of the Forecast volcano were successfully collected through these processes. A comparison between the bathymetric maps from the MBES and those from the Onnuri Research Vessel, the mother ship of the ROV Hemire for these explorations, is also presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.408-416
• /
• 2010

A study on the calibration of an X-band HPS(Hongik Polarimetric Scatterometer) system for ground-based operation is presented in this paper. In order to calibrate the scatterometer system, the degree of its distortions are analyzed by comparison between theoretical- and measured-values using the theoretically well-known calibration targets such as a metal sphere, a trihedral corner reflector(CR) and a metal cylinder. The calibration works in the field conditions depend on the precise and stable measurements of those calibration target. we present a measurement technique, so-called, an automatic 2-D target-scanning technique, using the incidence-angle(${\xi}-$ and ${\phi}-$ directions) control of HPS system. Then, we used STCT(Single-Target Calibration Technique) and GCT(General Calibration Technique) to calibrate a distortion of the scatterometer system, and measured the polarimetric RCS(Radar Cross Section) and phase-difference of a trihedral-CR as a test-target to verify the accuracy of the calibration technique. Then, three different types(i.e., 10, 20, 30 cm) of trihedral-CR were used. we obtained the error ranges about ${\pm}1.0$dB, ${\pm}0.5$ dB in a polarimetric RCS and about $-20^{\circ}{\sim}0^{\circ}$ and ${\pm}5^{\circ}$ in the co-polarized phase-difference by using the GCT and STCT, respectively.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.8
• /
• pp.67-75
• /
• 2004

The landslide is one of the most significant natural disasters, which cause a lot of loss of human lives and properties. The landslides in natural slopes generally occur by complicated problems such as soil properties, topography, and geology. Artificial Neural Network (ANN) model is efficient computing technique that is widely used to solve complicated problems in many research fields. In this paper, the ANN model with application of error back propagation method was proposed for estimation of landslide hazard in natural slope. This model can evaluate the possibility of landslide hazard with two different approaches: one considering only soil properties; the other considering soil properties, topography, and geology. In order to evaluate reasonably the landslide hazard, the SlideEval (Ver, 1.0) program was developed using the ANN model. The evaluation of slope stability using the ANN model shows a high accuracy. Especially, the prediction of landslides using the ANN model gives more stable and accurate results in the case of considering such factors as soil, topographic and geological properties together. As a result of comparison with the statistical analysis(Korea Institute of Geosciences and Mineral Resources, 2003), the analysis using the ANN model is approximately equal to the statistical analysis. Therefore, the SlideEval (Ver. 1.0) program using ANN model can predict landslides hazard and estimate the slope stability.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.26 no.4
• /
• pp.419-432
• /
• 2010

Various torque generating devices have been developed and employed to apply a proper torque. These devices are usually calibrated by the manufacturer to apply appropriate torque levels for their specific implants and attachments. The purpose of this investigation was to determine and compare the accuracy of the torque controllers. In this study, 4 types of torque controllers were used; torque limiting device(TLD), torque indicating device(TID) and contra angle torque driver(CA), electronic torque controller(ETC). Digital torque gauge was employed to measure the de-torque value. Thirty cycles of tightening and loosening were repeated with each torque controller. All implant torque controllers have shown slight errors and deviations. The contra angle torque driver exhibited the most accurate data. In the limitation of this study, it would be recommended that the implant torque controllers should be checked whether uniformed and precise torque can be generated and a measuring error should be corrected.

• Journal of Gastric Cancer
• /
• v.3 no.4
• /
• pp.182-185
• /
• 2003

Purpose: Preoperative staging of gastric cancer is crucial because the treatment modality and the prognosis depend upon the stage of gastric cancer. Current treatment modalities for early gastric cancer have focused on the quality of life. Endoscopic ultrasonography (EUS) and abdominal computed tomography (CT) are commonly used diagnostic tools to evaluate the invasiveness (T stage) of the primary tumor. The purpose of this paper is to evaluate the sensitivity and the specificity of preoperative EUS and CT in comparison with postoperative pathology. Materials and Methods: From October 2001 to October 2002, EUS and abdominal CT were performed simultaneously on 75 patients who underwent radical gastric surgery for the treatment of gastric cancer. Through analyzing the clinical T stage and the pathologic T stage, We evaluated the diagnostic sensitivities and specificities of endoscopic ultrasonography and abdominal computed tomography. Results: The male-to-female sex ratio was 1 : 0.6 (males: 47, females: 28). The mean age was 55.4 years in males (range: $28\~81$) and 54.4 years in females (range: $23\∼77$). The clinical T stage based on EUS included 22 T1mm, 7 T1sm, 22 T2, and 24 T3. The clinical T stage based on CT included 20 Tx, 23 T2, and 32 T3. The permanent pathologic report confirmed 23 T1mm, 10 T1sm, 17 T2, 24 T3, and 1 T4. The sensitivity and specificity of EUS were $84.2\%\;and\;94.7\%$, respectively. However, the sensitivity and specificity of abdominal CT were $53.3\%\;and\;77.0\%$, respectively. Conclusion: Our data suggest that EUS is a very useful diagnostic tool for evaluating the T stage of gastric cancer because EUS has higher specificity than abdominal CT. Therefore, EUS may have a significant role as a preoperative diagnostic modality in patients undergoing minimally invasive surgery.

• Asian-Australasian Journal of Animal Sciences
• /
• v.26 no.6
• /
• pp.788-794
• /
• 2013

Mastitis set apart as clinical and sub clinical is a disease complex of dairy cattle, with sub clinical being the most important economically. Of late, laboratories showed interest in developing biochemical markers to diagnose sub clinical mastitis (SCM) in herds. Many workers reported noteworthy alternation of acute phase proteins (APPs) and nitric oxide, (measured as nitrate+nitrite = NOx) in milk due to intra-mammary inflammation. But, the literature on validation of these parameters as indicators of SCM, particularly in riverine milch buffalo (Bubalus bubalis) milk is inadequate. Hence, the present study focused on comparing several APPs viz. ${\alpha}_1$-anti trypsin, ${\alpha}_1$-acid glycoprotein, fibrinogen and NOx as indicators of SCM in buffalo milk. These components in milk were estimated using standardized analytical protocols. Somatic cell count (SCC) was done microscopically. Microbial culture was done on 5% ovine blood agar. Of the 776 buffaloes (3,096 quarters) sampled, only 347 buffaloes comprising 496 quarters were found positive for SCM i.e. milk culture showed growth in blood agar with $SCC{\geq}2{\times}10^5$ cells/ml of milk. The cultural examination revealed Gram positive bacteria as the most prevalent etiological agent. It was observed that ${\alpha}_1$-anti trypsin and NOx had a highly significant (p<0.01) increase in SCM milk, whereas, the increase of ${\alpha}_1$-acid glycoprotein in infected milk was significant (p<0.05). Fibrinogen was below detection level in both healthy and SCM milk. The percent sensitivity, specificity and accuracy, predictive values and likelihood ratios were calculated taking bacterial culture examination and $SCC{\geq}2{\times}10^5$ cells/ml of milk as the benchmark. Udder profile correlation coefficient was also used. Allowing for statistical and epidemiological analysis, it was concluded that ${\alpha}_1$-anti trypsin indicates SCM irrespective of etiology, whereas ${\alpha}_1$-acid glycoprotein better diagnosed SCM caused by gram positive bacteria. NOx did not prove to be a good indicator of SCM. It is recommended measuring both ${\alpha}_1$-anti trypsin and ${\alpha}_1$-acid glycoprotein in milk to diagnose SCM in buffalo irrespective of etiology.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.1
• /
• pp.259-263
• /
• 2015

Background: In the field of cancer, the ICD-10 coding convention is based on the site of a neoplasm in the body and usually ignores the morphology, thus the same code may be assigned to tumors of different morphologic types in an organ. Nowadays, all general (provincial) and center hospitals in Thailand are equipped with the hospital information system (HIS) database. Objective: This study aimed to find the characteristics and magnitude of agreement represented by the positive predictive value (PPV) of provisional cancer diagnoses in the HIS database in Pattani Hospital in Thailand in comparison with the final cancer diagnosis of the ICD-10 codes generated from a well established cancer registry in Songklanagarind Hospital, the medical school hospital of Prince of Songkla University. Materials and Methods: Data on cancer patients residing in Pattani province who visited Pattani Hospital from January 2007 to May 2011 were obtained from the HIS database. The ICD-10 codes of the HIS computer database of Pattani Hospital were compared against the ICD-10 codes of the same person recorded in the hospital-based cancer registry of Songklanagarind Hospital. The degree of agreement or positive predictive value (PPV) was calculated for each sex and for both sexes combined. Results: A total of 313 cases (15.9%) could be matched in the two databases. Some 222 cases, 109 males and 113 females, fulfilled the criteria of referral from Pattani to Songklanagarind Hospitals. Of 109 male cancer cases, 76 had the same ICD-10 codes in both hospitals, thus, the PPV was 69.7% (95%CI: 60.2-78.2%). Agreement in 76 out of 113 females gave a PPV of 67.3% (95%CI: 57.8-75.8%). The two percentages were found non-significant with Fisher's exact p-value of 0.773. The PPV for combined cases of both sexes was 68.5% (95%CI: 61.9-74.5%). Conclusions: Changes in final diagnosis in the referral system are common, thus the summary statistics of a hospital without full investigation facilities must be used with care, as the statistics are biased towards simple diseases able to be investigated by available facilities. A systematic feedback of patient information from a tertiary to a referring hospital should be considered to increase the accuracy of statistics and to improve the comprehensive care of cancer patients.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.12
• /
• pp.5147-5152
• /
• 2016

Background: Investigations of methods for detection of mutations have uncovered major weaknesses of direct sequencing and pyrosequencing, with their high costs and low sensitivity in screening for both known and unknown mutations. High resolution melting (HRM) analysis is an alternative tool for the rapid detection of mutations. Here we describe the accuracy of HRM in screening for KRAS and BRAF mutations in metastatic colorectal cancer (mCRCs) samples. Materials and Methods: A total of 1000 mCRC patients in Mehr Hospital, Tehran, Iran, from Feb 2008 to May 2012 were examined for KRAS mutations and 242 of them were selected for further assessment of BRAF mutations by HRM analysis. In order to calculate the sensitivity and specificity, HRM results were checked by pyrosequencing as the golden standard and Dxs Therascreen as a further method. Results: In the total of 1,000 participants, there were 664 (66.4%) with wild type and 336 (33.6%) with mutant codons 12 and/or 13 of the KRAS gene. Among 242 samples randomly checked for the BRAF gene, all were wild type by HRM. Pyrosequencing and Dxs Therascreen results were in line with those of the HRM. In this regard, the sensitivity and specificity of HRM were evaluated as 100%. Conclusion: The findings suggest that the HRM, in comparison with DNA sequencing, is a more appropriate method for precise scanning of KRAS and BRAF mutations. It is also possible to state that HRM may be an attractive technique for the detection of known or unknown somatic mutations in other genes.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.2
• /
• pp.307-318
• /
• 2015

In this study, the efficiency of two-dimensional inundation analysis using road network was demonstrated in order to reduce the simulation time of numerical model in urban area. For this objective, three simulation conditions were set up: Case 1 considered only inundation within road zone, while Case 2 and 3 considered inundation within road and building zone together. Accordingly, Case 1 used grids generated based on road network, while Case 2 and 3 used uniform and non-uniform grids for whole study area, respectively. Three simulation conditions were applied to Samsung drainage where flood damage occurred due to storm event on Sep. 21, 2010. The efficiency of suggested method in this study was verified by comparison the accuracy and simulation time of Case 1 and those of Case 2 and 3. The results presented that the simulation time was fast in the order of Case 1, 2 and 3, and the fit of inundation area between each case was more than 85% within road zone. Additionally, inundation area of building zone estimated from inundation rating index gave a similar agreement under each case. As a result, it is helpful for study on real-time inundation forecast warning to use a proposed method based on road network and inundation rating index for building zone.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.9 no.1
• /
• pp.37-47
• /
• 2007

The shield tunneling method has been increasingly employed to minimize environmental damages and civil complaints in the populated and developed area. A lining segment, which is a main structure of the shield tunnel, consists of joints. Conventional foreign and domestic design data have been commonly used for design practices without a specific verification of structural analysis models, design load, and the effect of soil characteristics on the performance of lining segment. In this study, the suitability of existing analytic models used for the design of shield tunnel lining segment has been evaluated through a comparison between analytical and numerical solutions. Based on the evaluation of their suitability performed in the study, a full-circumferential beam jointed spring model (1R-S0) is proposed for design practices by considering user's convenience, the applicability of field conditions and the accuracy of analysis result. By using the proposed model, the parameter analysis was performed to investigate the effects of joint stiffness, ground rigidity, joint distribution and the number of joints on the behavior of lining segment. Parameters considered in the investigation have been appeared to affect the behavior of lining segment. Among those parameters, joint stiffness has been appeared to have the most significant effect on the bending moment and displacement of lining segment.