• International Journal of Air-Conditioning and Refrigeration
• /
• v.10 no.1
• /
• pp.19-30
• /
• 2002

This paper addresses characteristics of compressible flow dynamics inside a pipe with an accumulator and an inlet orifice. It also presents a simple but stable numerical method associated with the accumulator-orifice calculation. In particular, a focus is given to developing a method of finding an optimum design of the accumulator-orifice system (i.e., the accumulator size and the throttle resistance) that gives the most effective dissipation of the water-hammering problem. It is found that there exists indeed an optimum set of parameter values for the most effective dissipation of the wave energy.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.197-204
• /
• 2004

An accumulator in hydraulic systems stores kinetic energy during braking action, and then that controls hasty surge pressure. An energy recovery system using accumulator seems to be advantageous for ERBS due to its high energy density. This study suggests a method to decide suitable accumulator volume for ERBS. The method is based upon energy conservation between kinetic energy of moving inertia and elastic energy of accumulator. The energy conversion was analyzed and a simple formula was derived. Also accumulator tests were conducted for different load mass and motor speed. A series of test work were carried out in the laboratory and the dynamic characteristics of the hydraulic motor system, such as the surge pressure and response time, were investigated in both brake action and acceleration action and these results show that the proposed design is effective for decision accumulator volume in ERBS.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.15-21
• /
• 2001

An accumulator in hydraulic systems stores kinetic energy during braking action, and then that controls hasty surge pressure. An energy recovery system using accumulator seems to be advantageous for ERBS due to its high energy density. This study suggests a method to decide suitable accumulator volume for ERBS. The method is based upon energy conservation between kinetic energy of moving inertia and elastic energy of accumulator. The energy conversion was analyzed and a simple formula was derived. A series of computer simulation was done to verify effectiveness of the formula. The results of the simulation work were compared with those of experiments and these results show that the proposed design is effective for decision accumulator volume in ERBS.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.1
• /
• pp.104-113
• /
• 2002

An accumulator in hydraulic systems stores kinetic energy during braking action and then that controls hasty surge pressure. An energy recovery system using accumulator seems to be advantageous far ERBS due to its high energy density. This study suggests a method to decide suitable accumulator volume far ERBS. The method is based upon energy conservation between kinetic energy of moving inertia and elastic energy of accumulator. The energy conversion was analyzed and a simple formula was derived. A series of computer simulation was done to verify effectiveness of the formu1a. The results of the simulation work were compared with those of experiments and these results show that the proposed design is effective far decision of accumulator volume in ERBS.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.5
• /
• pp.361-368
• /
• 2003

A new high-speed direct digital frequency synthesizer using a low power pipelined parallel accumulator is proposed. The proposed pipelined parallel accumulator uses both pipelining and paralleling techniques to increase speed and to reduce power consumption. The 2-pipelined 2-parallel accumulator only consumes 66% and 69% power of the 4-pipelined accumulator and the 4-parallel accumulator respectively with the same throughput. The proposed accumulator can achieve higher throughput with smaller area and less power consumption in lower clock frequency. All circuit simulations and implementations are based on a 0.35um CMOS process with VCC = 3.3V.

• Journal of KSNVE
• /
• v.6 no.4
• /
• pp.513-519
• /
• 1996

This paper is concerned with the bubble sound at the accumulator which is generated by the difference of the high pressure side and the low pressure side in the cycle of the refrigerator. The causes of the bubble sound generation are verified by the visualized test of the operating refrigerant flow at the accumulator and the measurements of the temperature and pressure. Two cases were tested, one with the accumulator has a orifice and the other with the accumulator hasn't a orifice. So that, it is presented the comparison of the bubble sound levels and spectrums in each cases. To predict the bubble sizes when they are generated, the linearized equation driven by Strasberg is used.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.973-978
• /
• 2001

Noise reduction has become a major issue of the manufacturing industry. This paper describes the reduction of noise and vibration of rotary compressors. Empirical design for the present strap of the accumulator has been considered to be sufficient for the constraint of the accumulator resonance modes without thorough study. Recently, however, some researchers found out that the accumulator contributes considerably to the sound propagation. In this paper, the contribution of accumulator to the noise propagation is investigated through sound measuring experiments by checking the directivity of the noise. And, experimental modal analysis results show that frequencies of some resonance modes of the accumulator coincide with the highest peaks on sound spectrum. To demonstrate the reason for those resonance modes, a finite element analysis is conducted. Normal mode analysis of the finite element model of the rotary compressor shows the mechanism of the accumulator resonance modes.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.641-647
• /
• 2004

Characteristics of the high frequency pulsatile flow have been investigated experimentally to understand the flow phenomena in the hydraulic system. The accumulator in high frequency hydraulic system but that is not effective all frequency zone. Therefore, a hydraulic damper used with accumulator is suggested to reduce the high frequency pulsatile where the accumulator is not effective. The pulsating pressure obtained by Pressure measurement system are analyzed to power spectral density distribution. According to the variations of pump input pressure and actuator acceleration frequency, the pressure is measured with or without an accumulator or pulsatile damper The amplitude of pressure with damper is very lower than those without accumulator or damper due to absorbing function of damper. As the frequency of actuator acceleration is increased, the effect of damper becomes very important to decrease the amplitude of pulsatile Pressure waveform with high frequencies.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.5
• /
• pp.388-397
• /
• 2001

This paper addresses characteristics of compressible flow dynamics inside a pipe with an accumulator and an inlet orifice. It also presents a simple but stable numerical method associated with the accumulator-orifice calculation. In particular, a focus is given to developing a method of finding an optimum design of the accumulator-orifice system (i.e., the accumulator size and the throttle resistance) that gives the most effective dissipation of the water-hammering problem. It is found that there exists indeed an optimum set of parameter values for the most effective dissipation of the wave energy.

• Aerospace Engineering and Technology
• /
• v.7 no.1
• /
• pp.8-14
• /
• 2008

Basic characteristics of wheel brake accumulator for aircraft is studied. Wheel brake accumulator maintains the braking pressure for parking mode, and also it supplies the hydraulic pressure to the wheel brake system for emergency mode. The design requirements of wheel brake accumulator are analyzed and the initial sizing is conducted. A wheel brake accumulator consists of a cylinder and a brake control module, and the basic configuration and detail components are presented. Again, structural static analysis of vessel is performed with NASTARN/PATRAN for preliminary design.