• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.52 no.1
• /
• pp.1-8
• /
• 2003

In this paper, an observer-based adaptive controller is proposed to control the longitudinal motion of vehicles. The standard gradient method is used to estimate the vehicle parameters, mass, time constant, etc. The inter-vehicle spacing and its derivatives are estimated by using the sliding mode cascade observer introduced in this paper. It is shown that the proposed adaptive controller is uniformly ultimately bounded. It is also shown that the errors of the relative distance, the relative velocity and the relative acceleration asymptotically converge to zero. The simulation results are presented to investigate the effectiveness of the proposed method.

• Steel and Composite Structures
• /
• v.9 no.2
• /
• pp.119-130
• /
• 2009

This paper reports results of the structural response of empty steel tanks under vertical ground motions. The tanks are modeled using a finite element discretization using shell elements, and the vertical motion is applied and analyzed using nonlinear dynamics. Several excitation frequencies are considered, with emphasis on those that may lead to resonance of the roof. The computational results illustrate that as the base motion frequency is tuned with the frequency of the first roof-mode of the tank, the system displays large-amplitude displacements. For frequencies away from such mode, small amplitude displacements are obtained. The effect of the height of the cylinder on the dynamic response of the tank to vertical ground motion has also been investigated. The vertical acceleration of the ground motion that induces significant changes in the stiffness of the tank was found to be almost constant regardless of the height of the cylinder.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.12
• /
• pp.2032-2038
• /
• 1989

Single mode optical fiber interferometeric sensors using phase tracking homodyne detection are typically susceptible to environmentally indured temperature fluctuations and other types of disturbances. A simple and effective phase tracking feedback electronic circuit for compensator is described to achieve stabilizing signal output, maximum sensitivity and linearity in the fiber optic Mach-Zehnder infterferometer in the presence of differential phase drift. The phase tracking range of the piezoelectric cyclinder in the reference arm is \ulcorner.7 \ulcornerad and the prabe mass about 1 gram in the sensing arm was used for measurements of the gravity acceleration.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.840-843
• /
• 1993

In this paper, an LPM controller using microprocessor was implemented and adopted Microstep method to control the LPW. In Microstep method, current waveform is sinusoidal not square. This method is characterized by less vibrating, less noisy, and more precise position control. Also, we simulate the static thrust characteristics for each waveform. The experiment was performed according to the mechanical vibration at the acceleration mode and slewing mode. The current tracks reference sinusoidal waveform well and stability was improved as we expected. Therefore, the possibility of the open loop position control was proposed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1394-1399
• /
• 2001

The purpose of this paper is that investigates the dynamic behavior characteristic of W.T.S(Wind Turbine System) and carries out the evaluation analysis during operating W.T.S. To investigate the dynamic behavior characteristic of W.T.S. the experiments to measure vibration of the blade from the attached accelerometer on the flap and edge section of the blade that is one of the most important elements of dynamic characteristic of W.T.S are performed. Natural frequency and mode shape are calculated with commercial program (STAR MODAL) using the measured vibration acceleration that receives the signal with F.F.T Analyzer from the accelerometer. For validation of these experiments. the finite element analysis is performed with commercial F.E.M Program (ANSYS) on the basis of the natural frequency and mode shape. The results indicate that experimental values have good agreements with the finite element analysis.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.4
• /
• pp.190-199
• /
• 1993

In this study a three-axes mobile robot which has two independently controlled driving wheels and a function of simultaneously steering the driving wheels has been developed. Two-motion modes of the mobile robot, the first is a differential velocity motion of two driving wheels and the second is a equal driving and steering motion, have been analyzed and the kinematic and dymanic analyses about the each motion mode have been carried out. As a result of dynamic analysis, the torque used on a motor control and acceleration have been derived explicitly. Hence, a computation time is saved effectively and a real time control of the mobile robot considering the dynamics has become possible. Through a simulation the results considering the dynamics have been compared with that no regarding the dynamics and the possibility of real-time control has been proved.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.104-104
• /
• 2011

The fuel economy estimates essentially serve two purposes : to provide consumers with a basis on which to compare the fuel economy of different vehicles, and to provide consumers with a reasonable estimate of the range of fuel economy they can expect to achieve. The current fuel economy label values utilize measured fuel economy over city driving cycles. However, this test driving mode can not be evaluated the variety factor of the real-world. These factors include differences between the way vehicles are driven on the road and over the test cycles, air conditioning use, widely varying ambient temperature and humidity, widely varying trip lengths, wind, precipitation, rough road conditions, hills, etc. The purpose of this paper is to account for three of these factors on the fuel economy : 1) on-road driving patterns (i.e. higher speeds and more aggressive driving (higher acceleration rates)), 2) air conditioning, and 3) colder temperatures. The new test methods will bring into the fuel economy estimates the test results from the five emissions tests in place today : CVS-75, HWFET, US06, SC03 and Cold CVS-75. Based on these new test methods, this paper discusses the characteristics of driving condition on Hybrid electric vehicle (HEV). And this paper assesses the fuel economy label of HEV.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.2
• /
• pp.278-294
• /
• 2015

Considering the guidance and control problem of the near space interceptor (NSI) during the terminal course, this paper proposes a three-channel independent integrated guidance and control (IGC) scheme based on the backstepping sliding mode and finite time disturbance observer (FTDO). Initially, the three-channel independent IGC model is constructed based on the interceptor-target relative motion and nonlinear dynamic model of the interceptor, in which the channel coupling term and external disturbance are regarded as the total disturbances of the corresponding channel. Then, the FTDO is introduced to estimate the target acceleration and control system loop disturbances, and the feed-forward compensation term based on the estimated values is employed to effectively remove the effect of disturbances in finite time. Subsequently, the IGC algorithm based on the backstepping sliding mode is also given to obtain the virtual control moment. Furthermore, a robust least-squares weighted control allocation (RLSWCA) algorithm is employed to distribute the previous virtual control moment among the corresponding aerodynamic fins and reaction jets, which also takes into account the uncertainty in the control effectiveness matrix. Finally, simulation results show that the proposed IGC method can obtain the small miss distance and smooth interceptor trajectories.

• Earthquakes and Structures
• /
• v.11 no.2
• /
• pp.245-264
• /
• 2016

A suitable ground motion intensity measure (IM) plays a crucial role in the seismic performance assessment of a structure. In this paper, we introduce a scalar IM for use in evaluating the seismic response of single-layer reticulated domes. This IM is defined as the weighted geometric mean of the spectral acceleration ordinates at the periods of the dominant vibration modes of the structure considered, and the modal strain energy ratio of each dominant vibration mode is the corresponding weight. Its applicability and superiority to 11 other existing IMs are firstly investigated in terms of correlation with the nonlinear seismic response, efficiency and sufficiency using the results of incremental dynamic analyses which are performed for a typical single-layer reticulated dome. The hazard computability of this newly proposed IM is also briefly discussed and illustrated. A conclusion is drawn that this dominant vibration mode-based scalar IM has the characteristics of strong correlation, high efficiency, good sufficiency as well as hazard computability, and thereby is appropriate for use in the prediction of seismic response of single-layer reticulated domes.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.194-207
• /
• 2000

In this paper, we suggest a vision-based lane change control system, which can be applied on the straight road, without additional sensors such as a yaw rate sensor and a lateral accelerometer. In order to reduce the image processing time, we predict a reference line position during lane change using the lateral dynamics and the inverse perspective mapping. The sliding mode control algorithm with a boundary layer is adopted to overcome variations of parameters that significantly affects a vehicle`s lateral dynamics and to reduce chattering phenomenon. However, applying the sliding mode control to the system with a long sampling interval, the stability of a control system may seriously be affected by the sampling interval. Therefore, in this paper, a look ahead offset has been used instead of a lateral offset to reduce the effect of the long sampling interval due to the image processing time. The control algorithm is developed to follow the desired trajectory designed in advance. In the design of the desired trajectory, we take account of the constraints of lateral acceleration and lateral jerk for ride comfort. The performance of the suggested control system is evaluated in simulations as well as field tests.