• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.380-391
• /
• 2014

In this study, the scale effect on the performance of the podded propeller of tractor type is investigated. Turbulent flow computations are carried out for Reynolds numbers increasing progressively from model scale to full scale using the CFD analysis. The result of the flow calculation for model scale Reynolds numbers agrees well with that of the experiment of a large cavitation tunnel. The existing numerical analysis indicates that the performance of the podded propeller blades is mainly influenced by the advance coefficient and relatively little by the Reynolds number. However, the drag of pod housing with propeller in operation is different from that of pod housing without propeller due to the acceleration and swirl of propeller slipstream which is altered by propeller loading as well as the pressure recovery and friction according to Reynolds number, which suggests that the pod housing drag under the condition of propeller in operation is the key factor of the scale effect on the performance between model and full scale podded propellers. The so called 'drag ratio', which is the ratio of pod housing drag to total thrust of podded propeller, increases as the advance coefficient increases due to accelerated flow in the slipstream of the podded propeller. However, the increasing rate of the drag ratio reduces continuously as the Reynolds number increases from model to full scale progressively. The contribution of hydrodynamic forces, which acts on the parts composed of the pod housing with propeller operating in various loading conditions, to the thrust and the torque of the total propeller unit are presented for a range of Reynolds numbers from model to full scales.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.9
• /
• pp.831-837
• /
• 2015

Many persons and electronic devices are exposed to electromagnetic (EM) waves generated from magnetic resonance imaging (MRI) equipment, EM pulses (EMPs), and many other kinds of EM wave devices. Finger strips are used to provide shielding from these EM waves. Because of the high thermal conductivity of finger strips, they are used in the design of specialized doors that are installed in shielded rooms. In this study, we perform an accelerated life test using the load acceleration stress, which affects the main failure mode of finger strips. We predict the life of the finger strip under normal usage conditions based on the results of the accelerated life test. We compare the results with those predicted from the life test under normal usage conditions to evaluate the validity of accelerated life testing.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.4
• /
• pp.133-141
• /
• 2013

This paper describes the earthquake risk evaluation of 15 sites of architectural heritages, which are considered ground conditions of sites in Seoul. In order to acquire the input data of earthquake response analysis, surface wave exploration was performed at the site. Earthquake response analysis and 3D earthquake safety evaluation were carried out under the base of scenario earthquakes. Ground displacements of areas, which are located on architectural heritages, are showed about 0.5 mm ~ 9.7 mm, and it was analyzed to small affected by earthquakes. In case of Naksungdae three-story stone pagoda, ground displacement is similar to the others. However, displacement of three-story stone pagoda with granite is 30 mm on the top, because the greatest occurrence of that is caused by stress release at seismic wave effect.

• Journal of the Ergonomics Society of Korea
• /
• v.36 no.5
• /
• pp.535-543
• /
• 2017

Objective: This study was designed to identify factors affecting pilots' +Gz tolerance recovery from +Gz induced exhaustion. Background: +Gz tolerance of pilots has been considered as a crucial factor to fly the modern high performance fighter aircrafts. However, the factors affecting pilots' G-tolerance recovery from +Gz induced exhaustion have not been examined in the acceleration research community. Method: A centrifuge profile consisting of a high +Gz run for pilot's exhaustion and a low +Gz run for pilot's recovery and another high +Gz runs for pilot's second exhaustion was designed. The subjects' +Gz tolerance recovery ratio was measured by ratio of second high +Gz run time to the first high +Gz run time. The subjects' +Gz tolerance recovery rate was measured by dividing the subjects' +Gz tolerance recovery ratio by the low +Gz run time. The subjects' G-tolerance recovery rate was analyzed with respect to the subjects' personal factors including subjects' anthropometric and physiologic characteristics, flight time, flying aircraft type and so on. Results: The subjects' previous three-month flight hours (r=-0.336, p=0.039), six-month flight hours (r=-0.403, p=0.012) and one-year flight hours (r=-0.329, p= 0.044) correlated with the subjects' G-tolerance recovery rate. Conclusion: The subjects' G-tolerance recovery rate is clearly related to the subjects' previous flight hours. However, the subjects' anthropometric and physiologic characteristics do not show any statistically significant correlation with the subjects' G-tolerance recovery rate. Application: This research provides a safety critical insight to aviation community by identifying the factors to affect the gravity-induced loss of consciousness (GLOC) of pilots.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.6
• /
• pp.256-263
• /
• 2007

For $P_B=50Torr,\;P_T=5401Torr,\;T_S=450^{\circ}C,\;{\Delta}T=20K$, Ar=5, Pr=3.34, Le=0.01, Pe=4.16, Cv=1.05, adiabatic and linear thermal profiles at walls, the intensity of solutal convection (solutal Grashof number $Grs=7.86{\times}10^6$) is greater than that of thermal convection (thermal Grashof number $Grt=4.83{\times}10^5$) by one order of magnitude, which is based on the solutally buoyancy-driven convection due to the disparity in the molecular weights of the component A ($Hg_2Cl_2$) and B (He). With increasing the partial pressure of component B from 20 up to 800 Torr, the rate is decreased exponentially. It is also interesting that as the partial pressure of component B is increased by a factor of 2, the rate is approximately reduced by a half. For systems under consideration, the rate increases linearly and directly with the dimensionless Peclet number which reflects the intensity of condensation and sublimation at the crystal and source region. The convective transport decreases with lower g level and is changed to the diffusive mode at $0.1g_0$. In other words, for regions in which the g level is $0.1g_0$ or less, the diffusion-driven convection results in a parabolic velocity profile and a recirculating cell is not likely to occur. Therefore a gravitational acceleration level of less than $0.1g_0$ can be adequate to ensure purely diffusive transport.

• Korean Journal of Materials Research
• /
• v.30 no.6
• /
• pp.301-307
• /
• 2020

In this study, factors considered to be causes of promotion of densification of sintered pellets identified during phase change are reviewed. As a result, conclusions shown below are obtained for each factor. In order for MA powder to soften, a temperature of 1,000 K or higher is required. In order to confirm the temporary increase in density throughout the sintered pellet, the temperature rise due to heat during phase change was found not to have a significant effect. While examining the thermal expansion using the compressed powder, which stopped densification at a temperature below the MA powder itself, and the phase change temperature, no shrinkage phenomenon contributing to the promotion of densification is observed. The two types of powder made of Ti-silicide through heat treatment are densified only in the high temperature region of 1,000 K or more; it can be estimated that this is the effect of fine grain superplasticity. In the densification of the amorphous powder, the dependence of sintering pressure and the rate of temperature increase are shown. It is thought that the specific densification behavior identified during the phase change of the Ti-37.5 mol.%Si composition MA powder reviewed in this study is the result of the acceleration of the powder deformation by the phase change from non-equilibrium phase to equilibrium phase.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.6
• /
• pp.67-72
• /
• 2020

Life tests are essential in reducing the catastrophic damage caused by the accidents of large machinery such as aircraft and ships. However, life tests are challenging to implement due to the high costs and time required to test the life of large machinery parts. Therefore, it is advantageous and convenient to apply accelerated life test techniques for key components to reduce costs and time. In fact, extensive research has already been conducted on these techniques. However, recently, there have been cases in which an experimental value was applied to the shape parameter of the Weibull distribution used in the reliability test, but the test time was not significantly reduced. Therefore, in this paper, the shape parameters are estimated from the probability density function of the Weibull distribution for the analysis of an accelerated life test for bladder accumulators, which are core components of military helicopters. The test time was derived based on the number of samples and confidence level by substituting it into the test time equation. Next, the accelerated life test time was calculated using the steady-state test time with an acceleration factor obtained from the Arrhenius model. The steady-state life test required approximately 15,000 H, whereas the accelerated life test time for one sample at 100 ℃ was 34% shorter than that of the steady-state life test.

• Journal of Applied Reliability
• /
• v.14 no.4
• /
• pp.213-219
• /
• 2014

Wind turbine, which is attracting part of the renewable energy and is researching continuously, is going to be large size for high efficiency. There is a yaw system rotating the nacelle, weighted about 600 tons, to be perpendicular with the wind direction blowing in the large wind turbine. The wind turbine is focusing on the reliability improvement because working environment effect is bigger than any other points and specially, the reliability improvement of the yaw drive is required by the customer because it is the key component of the wind turbine. Because of this, the establishment of criteria for yaw drive is required because yaw drive system is the part of the wind turbine closely related with ensuring the reliability. So, this study did the failure analysis of the yaw drive system, which is consisted with 10 sets of yaw drives through researching and analyzing the site conditions. Also this study designed the life test method based on the failure analysis and working condition of the yaw drive. To design the accelerated life test of the yaw drive, this study reviewed the torque, lubrication condition, and frequency of use and etc. Finally, this selected the torque as the acceleration factor which is affected mainly to the system and also, the test equipment was developed based on the requirement of the life and performance test.

• Journal of Korean Society of Transportation
• /
• v.20 no.1
• /
• pp.121-130
• /
• 2002

Purpose of this paper is proposing technical evaluation method for safety on two-lane rural highways, this method can contribute to an establishment of the safety evaluation criteria and eventually contribute to the highway safety. In this study, accident data and field data(grade, radius, speed factor) are collected and are analyzed. And new technical evaluation method is proposed by problem in review of existent methods and analysis result. Property of new method is verified by comparing with existent one. Following are results of this study. 1) Proposed technical evaluation method is Proposed by using difference of speed variance and difference of acceleration. 2) In range of field survey, proposed method is more proper than existent one by comparing. 3) Headways under 6 second affect speed of next vehicle. 4) A point with the lowest speed in curve is placed about 35m from the beginning point. 5) Correlation of speed variance and severity of highway(EPDO) is statistically significant. For using proposed method, more tests are needed on other locations with various geometries. Moreover, advanced study is needed about classifying and giving the weight of each criterion.

• Journal of Digital Contents Society
• /
• v.8 no.2
• /
• pp.191-203
• /
• 2007

Increasing concern of urban community environment with acceleration of economic growth in modern generation, forcing us to recognize city's environment composition causes important factor for city's spirit. Since implementation of accountability of local government in 1995, local governments are thrives local government activation, compositing financially self support local government and competitiveness by others seeking number of methods for establishing traditional local images. In this study, analyzes cases in street environment facilities to help and support local government developing and applying special features of historical and cultural local images toward street environment facilities in city of Andong. For expression of local image in active installation of street environment facilities will increase tourism and extra value creating self esteem of local people will endures further rapid development of local government. local government seriously consider continuously supporting investment and research in street environment facilities.