• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.2
• /
• pp.37-41
• /
• 2017

Cuprous oxide ($Cu_2O$) is one of the potential candidates as an absorber layer in ultra-low-cost solar cells. $Cu_2O$ is highly desirable semiconducting oxide material for use in solar energy conversion due to its direct band gap ($E_g={\sim}2.1eV$) and high absorption coefficient that absorbs visible light of wavelength up to 650 nm. In addition, $Cu_2O$ has other several advantages such as non-toxicity, low cost and also can be prepared with simple and cheap methods on large scale. In this work, we deposited the $Cu_2O$ thin films by electrodeposition on gold coated $SiO_2/Si$ wafers. We changed the process conditions such as pH of the solution, applied potential on working electrode, and solution temperature. Finally, we confirmed the structural properties of the thin films by XRD and SEM.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.435-440
• /
• 2002

In this study, we have investigated photo-induced changes of optical energy gap( $E_{OP)}$ and photoluminescence (PL) in amorphous ($\alpha$-) S $e_{100-x}$G $e_{x}$ (x=5, 25 and 33) thin films prepared by conventional thermal evaporation method. In the $\alpha$-S $e_{100-x}$G $e_{x}$ thin film, the $E_{OP}$ is obtained by a linear extrapolation of the ($\alpha$hν)$^{\frac{1}{2}}$ versus hν plot to the energy axis using the optical absorption coefficient ($\alpha$) calculated from the extinction coefficient k measured in the wavelength range of 290~900nm. Although the values of $\Delta$ $E_{OP}$ are very different, all films exhibit photo-induced photo-darkening (PD) effect that is a red shift of $E_{OP}$ . In particular, $\Delta$ $E_{OP}$ in $\alpha$-S $e_{75}$ G $e_{25}$ thin film exhibits the largest value (i, e., $\Delta$ $E^{OP}$ ~40meV for $\alpha$-S $e_{95}$ G $e_{5}$ , $\Delta$ $E_{OP}$ ~200meV for $\alpha$-S $e_{75}$ G $e_{25}$ , $\Delta$ $E_{OP}$ ~130meV for $\alpha$-S $e_{67}$ G $e_{33}$ ). PL spectra in $\alpha$-SeGe by hν$_{HeCd}$ have no-Stokes shift (SS) and show a tendency dependent on both composition and illumination time. We explain the energy-induced phenomena such as the PD and thermal bleaching, the native charged-defect generation and the no-SS PL, etc..the PD and thermal bleaching, the native charged-defect generation and the no-SS PL, etc..tc..

• Journal of Sensor Science and Technology
• /
• v.8 no.3
• /
• pp.226-231
• /
• 1999

Pyroelectric infrared sensors have been fabricated using P(VDF/TrFE) film with pyroelectric effect. The weight percent and thickness of the poled P(VDF/TrFE) film are 75/25 percent and $25\;{\mu}m$ respectively. For easier fabrication and connection method new top and bottom electrodes design was adapted for human body detecting pyroelectric infrared sensor. An aluminum infrared absorption electrode and bottom electrode were deposited by thermal evaporator. And the device was mounted in TO-5 housing to detect infrared light of $5.5{\sim}14\;{\mu}m$ wavelength. The responsibility, NEP (noise equivalent power) and specific detectivity $D^*$ of the device were $9.62{\times}10^5\;V/W$, $3.95{\times}10^{-7}\;W$ and $5.06{\times}10^5\;cm/W$ under emission energy of $13\;{\mu}W/cm^2$ respectively.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.35 no.12
• /
• pp.1477-1485
• /
• 2011

Dyeability and colorfastness of the blended knits of cotton/rayon (40/60; C/R) and wool/tencel (10/90; W/T) are examined using the natural dyestuff ($Pinux^{TM}$) manufactured from Pinus radiata pine bark extract. In addition, pre-treatments (such as bleaching, mercerization and cationization) are performed to improve dyeability and colorfastness. The $Pinux^{TM}$ powder dyestuffs produced by Pinux Co., Ltd. are used as dyestuffs and their properties are examined for dyeing concentration (0.5-2% (owb)), dyeing time (30-120 minutes) and dyeing temperature (30-$90^{\circ}C$). Dyeability is evaluated with K/S value at 400nm, which is the maximum absorption wavelength for $Pinux^{TM}$. The results show the dyeability of W/T sample containing protein fiber with $Pinux^{TM}$ is superior to all cellulose fiber C/R. A concentration of dyestuff greater than 1.5% (owb), dyeing time 120 minutes and dyeing temperature of $90^{\circ}C$ are the most optimized conditions. It shows that the dyeability of C/R and W/T samples are high in the condition of an acid-dyeing bath and that dyeability highly declined in alkaline bath due to the instability of the proanthocyanidin pigment. After analyzing the effect of bleaching, mercerizing and cationizing (as pre-treatments on dyeability) it was concluded that the dyeability of the C/R sample was enhanced by mercerization but no significant effect by cationization. However, the simultaneous treatment of cationizing and dyeing resulted in far improved dyeability compared to dyeing after cationizing pre-treatment. As for the W/T sample, the effect of cationization was more prominent than the C/R sample. Colorfastness to color changes in the control W/T sample was higher than that of C/R's level 1-2, and it increased to Level 2 when bleaching pre-treatment was given and when a simultaneous cationizing treatment was adopted to the dyeing process. Colorfastness to light in W/T control sample resulted in Level 3 and further increased to an excellent Level of 4 with bleaching and simultaneous cationizing during dyeing process.

• Journal of Surface Science and Engineering
• /
• v.37 no.6
• /
• pp.307-312
• /
• 2004

Extensive efforts have been made in an attempt to utilize photocatalytic properties of $TiO_2$ in visible range. $TiO_2$ and TiO-N thin films were made by the DC reactive magnetron sputtering method at $300^{\circ}C$. Various gases (Ar, $O_2$ and $N_2$) were used and Ti target was impressed by 0.6 kW-5.8 kW power range. The hysteresis phenomenon of the $TiO_2$ thin film as a function of the discharge voltage characteristic was observed to be higher as applied power increases. That of TiO-N thin film was occurred at the 5.8 kW power. The cross section and surface roughness of thin films were observed by FE-SEM and AFM. Average surface roughness of TiO-N thin film was observed as $15.9\AA$ and that of $TiO_2$ as $13.2\AA$. The crystal phases of both $TiO_2$ and TiO-N thin films were found to be anatase structure. The atomic $\beta$-N (396 eV peak in N 1s XPS) was shown in the rutile crystal of TiO-N and was considered acting as the origin of wavelength shift to the visible light.

• Polymer(Korea)
• /
• v.37 no.6
• /
• pp.736-743
• /
• 2013

Novel carbazole based copolymers were synthesized by Suzuki coupling polymerization. (Diphenylene)vinylene and n-octyl was introduced to carbazole as pendants for reducing band gap and improving solubility, respectively. Thermal, photoluminescence and electro-luminescence of copolymers were studied for applying the emitting layer of polymer light emitting diode (PLED). Maximum UV-vis absorption and photoluminescence (PL) emission wavelength of copolymers showed 333~340 nm and 409~464 nm in solution state, respectively. The relative quantum yield using 9,10-diphenylanthracene as a reference was 25.8%. These copolymers exhibited high thermal stability ($T_d$ = $350^{\circ}C$) and good film forming ability. Good luminance was obtained at voltages lower than 8 V and the onset voltage was observed at 4.0 V.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.5 s.248
• /
• pp.413-421
• /
• 2006

The bubble dynamics induced by direct laser heating is experimentally analyzed as a first step to assess the technical feasibility of laser-based ink-jet technology. To understand the interaction between laser light and ink, the absorption spectrum is measured for various ink colors and concentrations. The hydrodynamics of laser-generated bubbles is examined by the laser-flash photography. When an Ar ion laser pulse (wavelength 488 nm) with an output power up to 600 mW is incident on the ink solution through a transparent window, a hemispherical bubble with a diameter up to ${\sim}100{\mu}m$ can be formed with a lifetime in a few tens of microsecond depending on the laser power and the focal-spot size. Parametric study has been performed to reveal the effect of laser pulse width, output power, ink concentration, and color on the bubble dynamics. The results show that the bubble generated by a laser pulse is largely similar to that produced by a thin-film heater. Consequently, the present work demonstrates the feasibility of developing a laser-actuated droplet generation mechanism for applications in ink-jet print heads. Furthermore, the results of this work indicate that the droplet generation frequency is likely to be further increased by optimizing the process parameters.

• Applied Chemistry for Engineering
• /
• v.23 no.6
• /
• pp.539-545
• /
• 2012

3-(2-benzotriazolovinyl)thiophene (BVT) was synthesized by the connection of the thiophene with the electron-withdrawing group, benzotriazole, through the vinylene. Its structure was confirmed by FT-IR, $^1H$-NMR, $^{13}C$-NMR and 2D hetero-cosy spectroscopy. Both BVT and 3-octylthiophene (OT) were copolymerized and showed an average molecular weight of 12000 (PDI 2.67) and 15000 (PDI 2.55), respectively. The copolymers were dissolved in the organic solvent such as chloroform, THF, TCE, etc. The mole ratios of BVT and OT in the synthesized copolymers were confirmed as 1 : 1.8 and 1 : 2.8 from $^1H$-NMR spectra. The UV-vis maximum absorption of copolymers appeared at the wavelength of 470 nm and 465 nm and the photoluminescence at ${\lambda}_{max}$ = 662 nm and 641 nm correspond to red-orange light. The band gaps of copolymers at 1.96 eV and 2.02 eV were found to be higher than those of poly(3-octylthiophene). The HOMO energy levels of the copolymers decreased overall in comparison with those of poly(3-octylthiophene), but the overall LUMO energy level increased.

• Laser Solutions
• /
• v.6 no.3
• /
• pp.19-28
• /
• 2003

The manufacturing process for the microfluidic device can include sequential steps such as master fabrication, electroforming, and injection molding. The laser ablation, using masks, has been applied to the fabrication of channels in microfluidic devices. In this research, an excimer laser was used to engrave microscopic channels on the surface of PET (polyethylene terephthalate), which shows a high absorption ratio for an excimer laser beam with a wavelength of 248 m. When 50-${\mu}{\textrm}{m}$-wide rectangular microscopic channels are ablated with a 500 ${\times}$ 500 ${\mu}{\textrm}{m}$ square mask at a magnification ratio of 1/10, ditch-shaped defects were found in both corners. The measurement of laser beam intensity showed that a coherent image in the PET target caused such defects. Analysis based on the Fourier diffraction theory enabled the prediction of the coherent shape at the image surface as well as the diffraction beam shape between the mask and the image surface. It also showed that the diameter of the aperture had a dominant effect. The application of aperture with a diameter of less than 3 mm helped to eliminate such defects in the ablated rectangular microscopic channels on PET without such ditch-shaped defects.

• Textile Coloration and Finishing
• /
• v.11 no.3
• /
• pp.15-22
• /
• 1999

This study investigated the mordanting effect of natural mordants such as camellia ash, bean chaff ash and pyrolignite of iron(Iron(II) Acetate) on silk fabrics dyed with green tea extracts. Experimental variables include the conditions of extraction and dyeing, and types of natural mordants. Inorganic ion contents In natural mordants were analysed by Induced Coupled Plasma Atomic Emission Spectrometer. In the ash Al, Fe, Si and Mn were in % unit, Cr and Ni were detected in ppm unit, and in the aqueous extracts of the ash all the metal ions were in ppm unit. On the other hand, fairly high content of Al(2.13% ) in camellia ash extract and Fe(7.91% ) in the aqueous extracts of pyrolignite iron were detected. The absorbance intensity of green tea extracts in UV-Visible spectrum increased with the temperature and time of extraction. The maximum absorption wavelength of the extracts appeared at 272.5nm and 210.5nm. The US values of silk fabrics dyed with green tea extracts were increased with temperature and time of dyeing. Surface color of silk fabric dyed with green tea extracts was 9.1YR, but it was changed from 7.9YR to 7.5YR by camellia ash extract and 7.4YR to 6.4YR by bean chaff ash extract with increase in mordant concentration. Pre-mordanted and post-mordanted fabrics with pyrolignite of iron were changed from 1.4YR to 1.1R and 7.2P to 4.2P, respectively.