• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.240-242
• /
• 2000

This study was investigated absorption properties of electromagnetic wave in thermal sprayed Sr-ferrite coatings. The experiment of this study was ; manufactured thermal spraying powder for improving absorption-efficiency, processed for increasing strength of thermal spray coatings, and measured the electromagnetic wave shielding efficiency. This study was obtained excellent absorption-efficiency by thermal sprayed Sr-ferrite coatings.

• Clean Technology
• /
• v.9 no.1
• /
• pp.43-48
• /
• 2003

As a result of study on factor affecting absorption efficiency using the structured packing, Mellapak N. 250Y for the chemical absorption of $CO_2$ that cause global warming due to development of industry, it is shown that Mellapak N. 250Y has lower pressure drop and superior efficiency of mass transfer than 25mm Pall ring. Also, in the absorption process, it produces high efficiency in the increase of load and concentration of absorption liquid and produces low efficiency in the increase of temperature. In the effect of overall mass transfer coefficient for 15% MEA on the temperature variation of absorbent, when absorbent temperature for 15% MEA varied as 25, 50, $80^{\circ}C$, overall mass transfer coefficients were shown as 0.83, 1.00, $0.90kmol/m^3-h-kPa$.

• Journal of the Optical Society of Korea
• /
• v.18 no.1
• /
• pp.9-14
• /
• 2014

We numerically investigate the effect of sunlight polarization on the absorption efficiency of V-shaped organic solar cells (VOSCs) using the finite element method (FEM). The spectral distribution of absorbance and the spatial distribution of power dissipation are calculated as a function of the folding angle for s-and p-polarized light. The absorption enhancement caused by the light-trapping effect was more pronounced for s-polarized light at folding angles smaller than $20^{\circ}$, where s-polarized light has a relatively larger reflectance than p-polarized light. On the other hand, the absorption efficiency for p-polarized light is relatively larger for folding angles larger than $20^{\circ}$, where the smaller reflectance at the interface of the VOSC is more important in obtaining high absorption efficiency.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.7
• /
• pp.360-365
• /
• 2017

Recently, development efforts of triple-effect absorption chiller have been increased in order to improve the efficiency of double-effect absorption chiller. However, triple-effect absorption chiller has some disadvantages, including high corrosion characteristic of LiBr solution at high temperature of $200^{\circ}C$. Moreover, it is necessary to develop new components for operation under high pressure of 2 bars even though COP is increased to 1.6 or 1.7. The objective of this study was to introduce a new system by combining double effect absorption chiller with single effect absorption chiller with multi-generators using bypass flow of LiBr dilute solution to $3^{rd}$ generator to overcome the disadvantages of triple-effect chiller and improve energy efficiency. Results indicate that the new absorption cycle had a much higher efficiency than double-effect chiller system, showing significant improvement when bypass solution flow rate of 25% was applied to the $3^{rd}$ generator using the main dilute solution of the absorber. The COP of the new chiller system was found to be 1.438, which was 21.7% higher than that (1.18) of the present double-effect system. The COP was decreased when solution by-pass rate to the $3^{rd}$ generator was increased. In addition, lower cooling water temperature caused higher COP. Therefore, the multi-generator system with by-pass solution might be an excellent chiller alternative to triple-effect absorption chiller with higher efficiency.

• The Research Journal of the Costume Culture
• /
• v.20 no.4
• /
• pp.475-484
• /
• 2012

The purpose of this study is to help to prevent daily noises by measuring the noise absorption coefficient of the non-woven fabrics and wallpapers which are commonly used in lining and noise absorption coefficient of lining curtain. Seven types of fiber materials for the interior decoration, one non-woven fabric for the wallpaper linings, and two types of textiles for curtain linings are used as the experimental materials in this study. The noise absorption coefficient of the noise absorbents were measured by using impedance tube. And the thermal transmittance were measured by using thermal transmittance tester. The results of this study are as follows; Observing the noise absorption efficiency of each experimental materials, the combination of fiber materials and linings, the noise absorption efficiency of cotton, polyester and silk were similar and for the experimental materials of flax, rayon, acrylic and nylon were resulted the similar noise absorption efficiency. The result of combination of fiber material and black fabric was highest among the combined linings. For the combination of fiber material and non-woven fabric, double layers of non-woven fabric resulted slightly higher noise absorption coefficient result than single layer of non-woven fabric. The thermal transmittance and the sound absorbents of experimental materials were affected by the thickness, density and layer of air of the experimental materials.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.4
• /
• pp.595-600
• /
• 2012

In this paper, it is investigated the characteristics of DSSC(Dye Sensitized Solar Cell) with cell area(0.25, 1, 2.25 $cm^2$) and dye absorption time(12, 24, 36 h). Thus, we obtain the following results by using the EIS, UV-VIS, I-V measurement. When the cell area increases, the efficiency decreases to 21~32 percent because of the increase about 40~$60{\Omega}$ of internal impedance regardless of dye absorption time. When the absorption time increases up to 24 hours, the efficiency increases to over 40 percent cause of the reduction of internal impedance regardless of cell area. When the dye absorption time becomes 36 hours, the internal impedance increases and at the same time, in the range of 600~700 nm, as the optical absorption reduces. Therefore, the efficiency decreases to 19~31 percent. When it is absorbed the dye for 24 hours in the smallest cell area which is 0.25 $cm^2$, the DSSC has the best efficiency (7.11 %).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.6
• /
• pp.557-563
• /
• 2016

The energy absorption efficiency of a wave power generation system is calculated as the ratio of the wave power to the power of the system. Because absorption efficiency depends on the dynamic behavior of the wave power generation system, a dynamic analysis of the wave power generation system is required to estimate the energy absorption efficiency of the system. In this study, a dynamic analysis of the wave power generation system under wave loads is performed to estimate the energy absorption efficiency. RecurDyn is employed to carry out the dynamic analysis of the system, and the Morison equation is used for the wave load model. According to the results, the lower the wave height and the shorter the period, the higher is the absorption efficiency of the system.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.03a
• /
• pp.294-301
• /
• 2003

The energy concept has been applied to the reported experimental results of six different structural steel connections to investigate the characteristics of system-dependent energy curve and energy absorption efficiency. For this the concept o( static and kinematic energy absorption efficiency has been defined. The present paper closes with the implication of the necessity of further investigation to extend the energy concept to reach the engineering practice.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.7
• /
• pp.567-574
• /
• 2013

An optical model is proposed in the white LED using phosphor and LED chip. In this paper a new model that describes the absorption rate and quantum efficiency with increasing the mixing ratio of phosphor in silicone, and the allotment of the phosphor absorption optical power in the several phosphor mixing in the silicone. Single phosphor in silicone from the optical measurement data before and after molding, the solution to get the blue optical power and the phosphor emission optical power is proposed. By these solution the absorption rate and the quantum efficiency was obtained. The model with single phosphor mixing in the silicone the validity was confirmed.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.1
• /
• pp.564-569
• /
• 2021

In this paper, for the typical LED and the tilted LED, when there is no electrode, when 20% absorption (80% reflection) occurs at the electrode, and when 60% absorption (40% reflection) occurs at the electrode, the effect of the absorption at the electrode and the height of the active region on the photon extraction efficiency and the mean photon path length was investigated, and an appropriate height of the active region was proposed. In a typical LED, as the absorption of the electrode increases, the photon extraction efficiency decreases from 18% to 15% and 13%, and the photon extraction efficiency is highest when the height of the active area is located in the center between the two electrodes. In the tilted LED, as the absorption of the electrode increases, the photon extraction efficiency decreases from 38% to 33% and 25%, and the photon extraction efficiency is highest when the height of the active area is located in the center between the two electrodes. The tilted LED can increase the photon extraction efficiency more than twice than that of a typical LED, where photons are trapped inside the chip due to total reflection.