• 펄프종이기술
• /
• 제39권3호
• /
• pp.24-29
• /
• 2007

The stress and strain properties of KOCC were modified to improve the performance of KOCC as a packaging raw material. The refining consistency, refining degree, blending conditions and the grammage of handsheet were varied. The stress-strain properties, tensile energy absorption were measured. The refining improved significantly the stress and strain properties of paper, especially at lower refining consistency. The increase of grammage also contributed to the improvement in the stress and strain of paper. It was also found that the refining, blending and grammage contributed to the increase of tensile energy absorption. However, it is strongly recommended to apply the combination of refining consistency, refining degree and mechanical treatment(blending).

• 한국안전학회지
• /
• 제9권4호
• /
• pp.112-118
• /
• 1994

Rock seems to be the ultimate excellent reaction for engineering loads, and often it Is. But the term rock includes a variety of types and conditions of material, some of which are surely not excellent and some that are potentially dangerous. Therefore, It is necessary to research absorption properties by rock strength. In this aspect the present paper deals essentially with the absorption exhibited by some Gneiss and Shale relation to its point load Index and specific gravity. In order to verify the rock strength, point load tester and two types rock specimen were used. Experimental results show that the absorption properties are highly dependent on rock strength. (suggested)

• International Journal of Internet, Broadcasting and Communication
• /
• 제10권4호
• /
• pp.1-5
• /
• 2018

The property of magnetic field and properties of EMW(Electro Magnetic Wave) absorption with multi-shaped EMW absorber was simulated. As a magnetic field having high density was showed at bottom of EMW absorber, simulation showed that overall EMW was absorbed at the bottom of multi-shaped absorber. The absorption properties of EMW according to thickness of absorber showed that it enhanced about 50-60 percent. Also, EMW absorption properties was checked with surface area of EMW absorber. A cylinder-shaped EMW absorber exhibited good property among multi-shaped EMW absorber based on these result.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.1155-1158
• /
• 2003

In this paper, we studied on the electrical characteristics of insulation material of elastomer epoxy. As the results of test, properties of epoxy represent differently according to elastomer contents. Also, its permittivity, tan ${\delta}$ and BDV(Break-Down Voltage) strength show big difference when those compare before moisture absorption test and after moisture absorption test. From this test we find results that mush elastomer contents can cause insulation properties to degrade.

• 한국의류학회지
• /
• 제40권3호
• /
• pp.495-505
• /
• 2016

This study explores and selects an appropriate material that considers light and soft physical properties as well as activity for impact absorption pads that can be used to develop practical impact protective clothes worn during daily life by the elderly to reduce the impact of falls. Physical properties, impact absorption performance, and compression characteristics were evaluated on 5 types of foam, 2 types of 3D spacer fabric, and 3 types of polymer gel to select a material appropriate for the pad to be inserted into impact protective clothes. The evaluation of the physical properties showed that 3D spacer fabrics had lower density compared to other materials and polymer gels had the highest density. The elongation percentage was higher in foams than 3D spacer fabrics and EPDM foam had the highest elongation percentage. The impact absorption performance of honeycomb polymer gel was better than foams and 3D spacer fabrics. As a result of looking into compression energy and compression characteristics of materials, 'CR foam A' was found to absorb the largest amount of compression energy, 24.1%, among foams and polymer gels. A high energy absorption rate of 50.0% (or above) was indicated by 3D spacer fabrics; however, foams and polymer gels showed a progressive deformation of energy compression / recovery curve with 3D spacer fabrics that showed drastic deformation. Based on characteristics of materials, 'CR foam C' and EPDM with relatively high absorption performance can be used as protective pad materials among foams. Among polymer gels, 2 open-type polymer gels that have relatively low impact protective performance but a relatively lighter weight on human body (compared to closed-type) are considered appropriate protective pad materials.

• 반도체디스플레이기술학회지
• /
• 제9권2호
• /
• pp.33-39
• /
• 2010

The moisture absorption properties such as diffusion coefficient and moisture content ratio of liquid type epoxy resin systems with the filler were investigated. Bisphenol A type and Bisphenol F type epoxy resin, Kayahard MCD as hardener and 2-methylimidazole as catalyst were used in these epoxy resin systems. The nano-sized spherical type fused silica as filler were used in order to study the moisture absorption properties of these liquid type epoxy encapsulant according to the change of filler size. The temperature of glass transition (Tg) of these epoxy resin systems was measured using Dynamic Scanning Calorimeter (DSC), and the moisture absorption properties of these epoxy resin systems according to the change of time were observed at $85^{\circ}C$ and 85% relative humidity condition using a thermo-hygrostat. The diffusion coefficients in these systems were calculated in terms of modified Crank equation based on Ficks' law. An increase of Tg and diffusion coefficient with filler size in these systems can be observed, which are attributed to the increase of free volume with Tg. The change of maximum moisture absorption ratio according to the filler size and filler content cannot be observed; however, the diffusion coefficients of these systems decreased with filler content. The diffusion via free volume is dominant in the epoxy resin systems with low nano-sized filler content; however, the diffusion with the interaction of absorption according the increase of the filler surface area is dominant in the liquid type epoxy encapsulant with high nano-sized filler content.

• 한국산학기술학회논문지
• /
• 제22권4호
• /
• pp.131-139
• /
• 2021

이 논문은 흡수율이 높은 제올라이트를 일반 굵은골재의 대체재로 보도용 조경포장 콘크리트에 적용하기 위한 기초 연구로서, 제올라이트 굵은골재 대체율에 따른 포장 콘크리트의 흡수성능과 강도 특성을 파악하였다. 제올라이트 굵은골재의 흡수율은 약 14%로서 일반 굵은골재와 비교하여 흡수성능이 2.5배 증가하였다. 그리고, 제올라이트 굵은골재를 포장 콘크리트에 혼입하면 굵은골재 대체율에 따라 흡수율이 증가하고, 최대 대체율 50%에서 5.2%로 일반 포장 콘크리트와 비교하여 약 42% 증가하였다. 제올라이트 혼입 포장 콘크리트의 압축강도는 대체율 20%까지 증가한 후 감소하였지만 건설기준코드에서 규정하는 압축강도 기준은 모두 충족하였다. 휨강도는 대체율 10%까지 기준강도를 만족하였으나 대체율에 따라 강도가 감소하였으며, 포장 콘크리트의 균열저항성에 영향을 주는 쪼갬인장강도는 대체율 20%까지 일반 포장 콘크리트의 강도보다 크게 나타났다. 제올라이트 혼입 포장 콘크리트의 흡수성능과 강도 특성에 대한 연구결과로부터 제올라이트 굵은골재를 일반 굵은골재의 대체재로 적용이 가능함을 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.479-482
• /
• 1999

Cured epoxy resins are extensively used for the electrical insulation in high-voltage equipments. The bisphenol A-based epoxy resins lured with azine show, especially, good thermal properties and mechanical resistances. For the technical and economic reasons, varing amount of inorganic fillers are added to endow the required special properties. In the large generators and motors of power plants, epoxy insulation is disclosed to the harsh conditions like the superheated steam and abrupt temperature variation. Hygrothermal aging at elevated temperatures tends to induce degradation in epoxy resins. To predict the effect of this degradation in DGEBA/MDA/SN/zeolite system, we proceeded the forced moisture absorption experiment using the autoclave. The thermal properties of the untreated and treated specimens were analyzed by DSC and TGA under the nitrogen flowing condition. The moisture absorption results showed a weight increase during hygrothermal aging at 1207. At the initial aging period, the system leaded to more or less postcuring but more prolonged environmental aging leaded the discoloration of specimen and lowering the T$_{g}$./.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.359.1-359.1
• /
• 2016

The electromagnetic (EM) properties of media, such as propagation, focusing and scattering, strongly rely on the electric permittivity and the magnetic permeability of media. Recently, artificially-created metamaterials (MMs) composed of periodically-arranged unit cells with tailored electric permittivity and magnetic permeability have drawn wide interest due to their capability of adjusting the EM response. MM absorbers using the conventional sandwich structures usually have very high absorption at a certain frequency, and the absorption properties of MMs can be adjusted simply by changing the geometrical parameters of unit cell. In this work, we suggested an incident-angle-independent broadband perfect absorber based on resistive layers. We analyze the absorption mechanism based on the impedance matching with the free space and the distribution of surface currents at specific frequencies. From the simulation, the absorption was expected to be higher than 96% in 1.4-6.0 GHz. The corresponding experimental absorption was found to be higher than 96% in 1.4-4.0 GHz, and the absorption turned out to be slightly lower than 96% in 4.0-6.0 GHz owing to the irregularity in the thickness of resistive layers.

• The Journal of the Acoustical Society of Korea
• /
• 제21권2E호
• /
• pp.81-90
• /
• 2002

Single absorbing materials and Helmholtz resonators have limited absorption characteristics over limited frequency ranges due to their structures and properties. Porous materials are highly absorptive for mid and high frequency ranges, while they have little sound absorption for low frequency sounds. Helmholtz resonators are generally used to absorb sound energy for a specified frequency range. Hence they have limited capability in controlling the overall acoustic properties of a space. Not much has been known about useful finishing materials which have enough rigidity and absorption over broad frequency range, in spite of wide demands from acoustic designers and consultants. The present work measured and analyzed absorption characteristics of a slit absorber by varying surface materials, depths of air gap, dimensions of slat and slit widths. It was found that the narrower the slit width, the larger the absorptions over the wide frequency ranges and the pattern was dependent on the presence of porous material. Narrower slat's width tend to increase the slit absorber's absorption more or less. Absorption coefficients at low frequency ranges were dramatically improved (from 0.23 to 0.56) by increasing air gap when porous materials were present.