• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.151.1-151.1
• /
• 2017

This work studied the corrosion behavior of AZ31 Mg alloy galvanically coupled with Cu during immersion in 0.1 and 0.5 M NaCl solutions by in-situ observation and galvanic corrosion current measurement using a zero resistance ammeter. The corrosion behavior of AZ31 Mg alloy was also studied by salt spray test. The average galvanic corrosion density during 2 h immersion in 0.1 NaCl solution was found to decrease as an exponential function with increasing the surface area ratios between AZ31:Cu or with increasing the distance between AZ31 and Cu. The corrosion of electrodeposited Cu on AZ31 Mg alloy was concentrated at the area next to Cu (about 5 mm for immersion test and 2 mm for salt spray test) and pitting corrosion was accelerated at the area beyond the severely corroded area by the galvanic coupling effect.

• 소성∙가공
• /
• 제20권8호
• /
• pp.601-610
• /
• 2011

Based on the facts that AZ31 magnesium alloy can be blow formed just like superplastic aluminum alloys and that most superplastic alloys fail by cavitation, the present study was undertaken to investigate the cavitation behavior of a fine-grained AZ31 sheet during blow forming at the elevated temperature. Other points of interest included the much lower strain rate and temperature dependencies of the magnesium alloy compared with conventional superplastic alloys. It was also aimed to find if cavitation in the AZ31 alloy can be suppressed by hydrostatic pressure, as is the case in most superplastic alloys. Interestingly, the application of hydrostatic pressure did not increase the blow formability of AZ31 sheet, even though it reduced the degree of cavitation. A possible reason for this behavior is discussed.

• 한국레이저가공학회지
• /
• 제9권1호
• /
• pp.25-29
• /
• 2006

This study aimed to investigate the change of mechanical properties with the rolling direction and shielding condition during laser welding of AZ31 magnesium alloy. AZ31 magnesium alloy sheets of 1mm thickness were welded using a continuous wave Nd:YAG laser with and without Ar shielding gas. The effect of Ar shielding gas and rolling direction on the mechanical properties were investigated using Vickers hardness, transverse-weld tensile. Porosity in the weld metals was investigated using an optical microscope. The experimental results showed that mechanical properties of AZ31 magnesium alloy laser welds were upgraded compared to those of base metal. Mechanical properties of AZ31 magnesium alloy laser welds were not substantially changed when Ar shielding gas was supplied.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.194.1-194.1
• /
• 2016

The present study investigated the effect of zincate treatment time on the dissolution behavior and the deposition of copper by immersion process and electroplating process on AZ31 Mg alloy substrate in a copper pyrophosphate bath. Without zincate pretreatment, the AZ31 Mg substrate quickly dissolved in the copper pyrophosphate solution although an external cathodic current was applied. The copper layers deposited on non-zincate treated AZ31 Mg alloy substrate by both immersion and electroplating processes showed very porous structure and very poor adhesion. With increasing zincate treatment time up to 2 min, the dissolution of AZ31 substrate in pyrophosphate solution rapidly decreased and the deposited copper layer was less porous and exhibited stronger adhesion. The immersion of AZ31 Mg sample in zincate solution for 5 min was found as a critical time for producing a non-porous and adherent electrodeposited copper layer on AZ31 Mg alloy. The optimum zincating time can be determined by observing the open circuit potential (OCP) of AZ31 Mg alloy samples in a copper pyrophosphate electroplating bath. The OCP reached a stable value of about -0.10 V (vs. SCE) after 5 min of immersion in the copper pyrophosphate electroplating solution.

• 한국군사과학기술학회지
• /
• 제15권3호
• /
• pp.315-321
• /
• 2012

In the study, corrosion characteristics of AZ31 magnesium alloy under various environments exposed during machining(immersion in cutting oil, 5 % cutting oil aqueous solution and distilled water & contact with dissimilar metals, SPC4 and A5052-H32) were investigated. A corrosion test was performed AZ31 magnesium alloy was immersed in each electrolyte solution after contacting with each dissimilar metals, and the results were observed by an electron microscope. In immersion tests, corrosion of AZ31 magnesium alloy showed to be in the sequence of distilled water> 5 % cutting oil aqueous solution> cutting oil> air, and in the test of contact with dissimilar metals, corrosion showed to be in the sequence of SPC4> A5052-H32> AZ31. It can be concluded that to prevent corrosion during machining, AZ31 magnesium alloy must prevent contacting water and use magnesium alloy for raw material of Jig & Fixture.

• 한국주조공학회지
• /
• 제32권2호
• /
• pp.75-80
• /
• 2012

In this study, we are aimed to prevent grain growth of semi-solid AZ31 magnesium alloys during reheating process. The semi-solid AZ31+(Ca) billets were investigated by using metallographic analysis, X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy in order to elucidate the effect of Ca addition during reheating process. The grain growth of semi-solid AZ31+(Ca) billet was reduced with increasing Ca content during reheating. The grain size of AZ31+(Ca) billet decreased with increasing volume fraction of Al2Ca particles. The grain growth rate constant K calculated by Oswald ripening LSW theory in AZ31+1.5wt.% Ca billet was the lowest 129.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.281-284
• /
• 2007

The effect of Ca addition on the microstructure evolution and deformation behavior of AZ31 magnesium alloy produced by hot extrusion was investigated. For this purpose, Ca was added into AZ31 melts to the level of 0.7 and 2.0 wt.% Ca. Then, AZ31 base alloy and Ca modified AZ31 alloys were extruded at $383^{\circ}C$. Ca added alloys showed finer grain size and increased hardness value rather than AZ31 base alloy. After isothermal hot compression, the shape of tested specimen exhibited a noticeable anisotropy due to the crystallographic texture effect. The ratio of major and minor axes of ovality was not directly related to test condition and Ca amount. Flow stress level increases with the increase of Ca addition at temperature below $300^{\circ}C$ because of fine microstructure. However, at high temperature and low strain rate region ($400^{\circ}C$ and $10^{-3}s^{-1}$), reverse tendency was observed since main deformation mechanism changes from dislocation slip to grain boundary sliding or diffusional process at high temperature.

• 한국레이저가공학회지
• /
• 제18권1호
• /
• pp.1-6
• /
• 2015

High welding speed and narrow weld seam are favorable for welding of magnesium alloy. Magnesium alloy is recommended for the smart frame because it has several advantages such as low density, high thermal conductivity, EMI shielding capability and good cast ability. This study is for the assembly welding of the magnesium smart frame with high productivity, good performance and low cost. The window for battery on AZ91D frame produced by die-casting was prepared by CNC machining. Corresponding AZ31 blank of 0.2mm thickness was prepared by die-blanking cut. All system set was fixed at the stationary bed but the laser beam was manipulated by scanner up-to 1,000mm/s speed. The weld joint between AZ31 sheet and AZ91D frame was welded by fiber laser on 850~1,000W output power. The joint showed penetration enough but some humping bead. The distortion by the weld heat was almost free because of the quick dissipation of the heat by small beam size and fast welding. Consequently, the thinner magnesium foil was assembled successfully to the magnesium frame of mobile phone.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2011년도 춘계학술대회 및 Fine pattern PCB 표면 처리 기술 워크샵
• /
• pp.116-116
• /
• 2011

AZ31과 AZ80의 마그네슘합금 소재를 이용하여 분극곡선과 전기화학적 임피던스를 측정하였고, 다른 금속과 접촉하여 대기환경에 노출시킨 부식시험을 하였다. 그 결과 AZ31보다는 AZ80의 부식저항이 더 큰 것을 확인할 수 있었고, 마그네슘 모재가 이종금속과 접촉된 상황에서 Cu>Fe>Al의 접촉재 순으로 부식이 진행되었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 추계총회 및 학술대회 논문집
• /
• pp.18-18
• /
• 2012

마그네슘 합금의 화성처리는 주로 탈지-산세-디스머트-화성처리의 4단계를 거쳐 진행되는 것으로 알려져 있다. 즉, 마그네슘 합금은 공기 중에서 자연 산화막이 쉽게 생성되며 이때 생성된 산화막을 제거하기 위한 산세 공정이 필수적이다. 본 연구에서는 AZ91D 마그네슘 주조재에 주로 사용되어 왔던 다양한 산 종류에 따른 AZ31B 마그네슘 판재의 산 에칭 후의 표면 상태 및 부식 거동을 관찰하였다. 따라서 AZ31B에 적합한 산 종류를 선별하고 그에 따른 표면 거동에 대한 논의를 통하여 마그네슘 합금의 표면에 대한 이해를 높이고자 한다.