• Journal of the Korean Ceramic Society
• /
• 제24권5호
• /
• pp.411-416
• /
• 1987

Thermal expansions and thermal expansion coefficients of cordierite ceramics reinforced by SiC whiskers up to 40 vol. % were investigated. The composite specimens were hot pressed at 1523K for 30 min under 28.5 MPa pressing pressure in Ar atmosphere. Thermal expansions of the hot pressed composites were measured using a differential dilatometer up to 1262 K in air. Thermal expansions and thermal expansion coefficient of the composites increased with SiC whisker content. Thermal expansion behaviors of the composites were well explained by modelling parallel slabs randomly distributed on the whisker plane as the microstructural element of the composites.

• Transactions on Electrical and Electronic Materials
• /
• 제2권1호
• /
• pp.7-11
• /
• 2001

We measured the electron transport coefficients, the electron drift velocity, W, and the longitudinal diffusion coefficient, $D_{L}$, over the E/N range from 0.03 to 100 Td and gas pressure range from 0.133 to 122 kPa in the 0.526% and 5.05% $C_{3}F_{8}$-Ar mixtures by the double shutter drift tube with variable drift distance. And we calculated these electron transport coefficients by using multi-term approximation of Boltzmann equation analysis. We determined the electron collision cross sections set for $C_{3}F_{8}$ molecule by the comparison of measurement and calculation. Our special attention in the present study was focused upon the inelastic collision cross sections of the $C_{3}F_{8}$ molecule.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1544-1545
• /
• 2011

For quantitative understanding of gas discharge phenomena, we should know electron collision cross section. Processing plasma etching of semiconductor, and research are being used in the etching source $C_4F_6$ gas may be used by itself and mixed with other gases are also used. However, the molecular gas $C_4F_6$ study on the characteristics of the electron transport and the cross-sectional area of the decision is still lacking. Therefore, we understand the electron transport characteristics and analysed the electron transport coefficients. And to understand and interpret physical properties of the ionization coefficient ${\alpha}$/N, and the attachment coefficient ${\eta}$/N in $C_4F_6$ gas.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.537-540
• /
• 2001

This paper presents the characteristics of Ta-N thin-film for high precision resistors, which were deposited on Si substrate by DC reactive magnetron sputtering in an argon-nitrogen atmosphere(Ar-(4~16 %)$N_2$). Structural properties studied using X-ray diffraction(XRD) indicate the presence of TaN, $Ta_3N_5$ or a mixture of Ta-N phases in the films depending on the amount of nitrogen in the sputtering gas. The chemical composition are investigated by auger electro spectroscopy(AES). The optimized conditions of Ta-N thin-film resistors were deposited in 4 % $N_2$ gas flow ratio. Under optimum conditions, the Ta-N thin-film resistors are obtained a high resistivity, $\rho=305.7{\mu}{\Omega}cm$, a low temperature coefficient of resistance, TCR=-36 $ppm/^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제19권3호
• /
• pp.301-306
• /
• 2006

The electron drift velocity W and the product of the longitudinal diffusion coefficient and the gas number density $ND_{L}$ in the $0.525\;\%$ and $5.05\;\%$ $C_{3}F_8-Ar$ mixtures were measured by using the double shutter drift tube with variable drift distance over the E/N range from 0.03 to 100 Td and gas pressure range from 1 to 915 torr. And we determined the electron collision cross sections set for the $C_{3}F_8$ molecule by STEP 1 of electron swarm method using a multi-term Boltzmann equation analysis. Our special attention in the present study was focused upon the vibrational excitation and new excitations cross sections of the $C_{3}F_8$ molecule.

• Journal of the korean Society of Automotive Engineers
• /
• 제2권1호
• /
• pp.32-38
• /
• 1980

In the case of a automobile marking skid on road for a period of braking, in general, the automobile velocity just before rapid braking can be obtained by evaluating the coefficient of friction between tires and road. Up to now, the coefficient of friction has been derived from mean velocity measured by a time watch, but the automobile velocity obtained in this manner would be deviated from actual value considerably, due to errors arising from not only measuring time but other various factors. In this paper the presumption method of automobile velocity by accelerometer is presented so as to improve the accuracy of measurement, and to determine the velocity readily. The results obtained in this experiment show that the frictional coefficients between tires and road under the given experimental conditions are considered to take linear relation over the fixed velocity limits 30km/h to 50km/h while for the same limits of velocities the coefficients of friction by the time watch method are not valid ar low velocity range. It will be seen that the former is simple and reliable whilst the latter is cumbersome and unreliable.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.537-540
• /
• 2001

This paper presents the characteristics of Ta-N thin-(ibm for high precision resistors, which were deposited oni substrate by DC reactive magnetorn sputtering in an argon-nitrogen atmosphere(Ar-(4∼16%)N$_2$). Sturcutural properties sutided using X-ray diffraction (XRD) indicate the presence of TaN, Ta$_3$N$\sub$5/ or a mixture of Ta-N phases in the films depending on the amount of nitrogen in the sputtering gas. The chemical composition are investigated by auger electro spectroscopy(AES). The optimized conditions of Ta-N thin-film resistors were deposited in 4 % N$_2$ gas flow ratio. Under optimum conditions, the Ta-N thin-film resistors are obtained a high resistivity, $\rho$=305.7 ${\mu}$Ωcm, a low temperature coefficient of resistance, TCR=-36 ppm/$^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.97-100
• /
• 2001

This paper presents the characteristics of Ta-N thin-film strain gauges as high-temperature strain gauges, which were deposited on Si substrate by DC reactive magnetron sputtering in an argon-nitrogen atmosphere(Ar-(4∼16 %)N$_2$). These films were annealed for 1 hour in 2x10$\^$-6/ Torr vaccum furnace range 500∼1000$^{\circ}C$. The optimized conditions of Ta-N thin-film strain gauges were annealing condition(900$^{\circ}C$, 1 hr.) in 8% N$_2$ gas flow ratio deposition atmosphere. Under optimum conditions, the Ta-N thin-films for strain gauges is obtained a high resistivity, $\rho$=768.93 ${\mu}$Ω cm, a low temperature coefficient of resistance, TCR=-84 ppm/$^{\circ}C$ and a high temporal stability with a good longitudinal gauge factor, GF=4.12.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• 제12권4호
• /
• pp.136-145
• /
• 1998

This paper describes the FFT and coefficient analysis of vibration signals for preventive diagnosis of a mold transformer at normal and abnormal state. Varying applied voltage, loading current and temperature as control variables for he experiment, measurement variables such as magnitude of vibration signals, frequency spectrum and time series coefficient were analyzed. The vibration signals by variation of control variables were measured by acceleration sensor adhered on the surface of winding and core, and measurement variables were calculated using dat acquisition system. After analyzing the normal state, the structural distortion was also simulated. The vibration signals at abnormal state were measured by the same control variables variation as the normal state. As a result, vibration signals between normal and abnormal state could be distinguished by comparison of the perpendicular and horizontal vibration signal.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• 제26권3호
• /
• pp.113-119
• /
• 2014

We carried out flow and structural response analysis of a box-type artificial reef (AR), which is made of concrete and structural steel. From the flow analysis, the wake region and drag coefficient were evaluated and accordingly, the structural analysis was performed to evaluate the stress and deformation of the target reef by considering the pressure field obtained from the flow analysis. The concept of wake volume was presented to quantitatively estimate the wake region and its variation according to flow direction and velocity. From the results, it is shown that the flow responses are only sensitive to the flow direction; the structural responses are sensitive to both of the flow velocity and direction although the magnitudes are negligible; and the wake volume became 3.52 times the AR volume with an optimum installation condition ($30^{\circ}$, flow direction) of the target unit.