• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.11
• /
• pp.969-975
• /
• 2000

Laser direct writing of micro-patterned copper lines has been achieved by pyrolytic decomposition of copper formate films (Cu(HCOO)$_2$.4$H_2O$), as a metallo-organic precursor, using a focused CW Ar$^{+}$ laser beam (λ=514nm) on PCB boards and glass substrates. The linewidth and thickness of the lines wee investigated as a functin of laser power and scan speed. The profiles of the lines were measured by scanning electron microscope (SEM), surface profiler ($\alpha$-step) and atomic force measured by scanning electron microscope (SEM), surface profiler ($\alpha$-step) and atomic force microscopy (AFM). The electrical resistivities of the patterned lines were also investigated as a function of laser parameters using probe station and semiconductor analyzer. We compared resistivities of the patterned copper lines with these of the Cu bulk. Resistivities decreased due to changes in morphology and porosity of the deposit, which were about 3.8 $\mu$$\Omega$cm and 12$\mu$$\Omega$cm on PCB and glass substrates after annealing at 30$0^{\circ}C$ for 5 minutes.s.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.321-322
• /
• 2009

Al doped ZnO films deposited on glass substrate using RF magnetron sputtering in Ar and $Ar+H_2$ gas ambient at $100^{\circ}C$. The films deposited in $Ar+H_2$ were hydrogen-annealed at the temperature of $150\sim300^{\circ}C$ for 1hr. The lowest resistivity of $4.25\times10^{-4}{\Omega}cm$ was obtained for the AZO film deposited in $Ar+H_2$ after hydrogen annealing at $300^{\circ}C$ for 1hr. The average transmittance is above 85% in the range of 400-1000 nm for all films. The absorption efficiency of solar cell was improved by using the optimized AZO films as a top electrode.

• Applied Science and Convergence Technology
• /
• v.25 no.6
• /
• pp.145-148
• /
• 2016

This paper, Al-doped ZnO(AZO) thin films for application as transparent conducting oxide films were deposited on the Corning glass substrate by using RF magnetron sputtering system. The effects of various Argon gas flow rates on optical and electrical characteristics of AZO films were investigate sputtering method. The Carrier Concentration is enhanced as Ar gas rate increases, and also the oxygen vacancy concentration. The figure of merit obtained in this study means that AZO films which deposited Ar gas rate of 75 sccm have the highest Carrier concentration and Hall mobility, which have the highest photoelectrical performance that it could be used as transparent electrodes.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.3
• /
• pp.164-168
• /
• 2004

Polycrystalline silicon thin films were deposited by inductively coupled plasma (ICP) assisted magnetron sputtering using a gas mixture of Ar and $H_2$ on a glass substrate at $250^{\circ}C$. At constant Ar mass flow rate of 10 sccm, the working pressure was changed between 10mTorr and 70mTorr with changing $H_2$ flow rate. The effects of RF power applied to ICP coil and $Ar/H_2$ gas mixing ratio on the properties of the deposited Si films were investigated. The crystallinity was evaluated by both X-ray diffraction and Raman spectroscopy. From the results of Raman spectroscopy, the crystallinity was improved as hydrogen mixing ratio was increased up to$ Ar/H_2$=10/16 sccm; the maximum crystalline fraction was 74% at this condition. When RF power applied to ICP coil was increased, the crystallinity was also increased around 78%. In order to investigate the surface roughness of the deposited films, Atomic Force Microscopy was used.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.81-81
• /
• 2008

Applications of CdS films in this study are to exhibit a high conductivity when they are exposed at light with visible wavelength and sequentially to show a low conductivity in dark state. For this purpose, CdS films should have a high photosensitivity, still maintaining a high conductivity at a visible light. In this study, CdS films were prepared at room temperature on glass substrates by rf magnetron sputtering. In order to increase the photo-conductivity in visible light, various defect levels should be located within the CdS band gap. In order to nucleate the defect sites within the CdS band gap, CdS films were deposited on glass substrates at room temperature using various $H_2$/(Ar+$H_2$) flow ratios by an rf magnetron sputtering. Through the investigation of the structural and photoconductive properties of CdS films by an addition of hydrogen, the relationship between photo- and dark-resistance in CdS films was investigated in detail. 200-nm-thick CdS films for photoconductive sensor applications were prepared at various $H_2$/(Ar+$H_2$) flow ratios on glass substrates at room temperature by rf magnetron sputtering. Sulfur concentration in CdS films crystallized at room temperature with (002) preferred orientation depends directly on the hydrogen atmosphere and the surface roughness of the films gradually increases with increasing hydrogen atmosphere. Films deposited at 8% of $H_2$/(Ar+$H_2$) exhibit an abrupt decrease of dark- and photo-resistance, showing a low photo-sensitivity ($R_{dark}/R_{photo}$). Onthe other hand, films deposited at a hydrogen atmosphere of 42% exhibit a photo-sensitivity of $5\times10^3$, maintaining a photo-resistance of an approximately $2\times10^4\Omega$/square. The dark- and photo-resistance values of CdS films were related with a composition, surface roughness, and defect sites within the band gap.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.62.1-62.1
• /
• 2011

The structural, optical, and electrical properties of Ga-doped ZnO (GZO) thin films on glass substrates grown by radio-frequency(RF) magnetron sputtering were investigated. The flow ratio of Ar was varied as a deposition parameter for growing high-quality GZO thin films. The structural properties and surface morphologies of GZO were characterized by the X-ray diffraction. To analyze the optical properties of GZO, the optical absorbance was measured in the wavelength range of 300-1100 nm by using UV-VIS spectrophotometer. The optical transmittance, absorption coefficient, and optical bandgap energy of GZO thin films were calculated from the measured data. The crystallinity of GZO thin films is improved and the bandgap energy increases from 3.08 to 3.23eV with the increasing Ar flow ratio from 10 to 100 sccm. The average transmittance of the films is over 88% in the visible range. The lowest resistivity of the GZO is $6.215{\times}10^{-4}{\Omega}{\cdot}cm$ and the hall mobility increases with the increasing Ar flow ratio. We can optimize the characteristics of GZO as a transparent electrode for thin film solar cells by controlling Ar flow ratio during deposition process.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.1
• /
• pp.119-126
• /
• 2022

MAS-based glass, which has been studied to replace the ceramic material used in the plasma etching chamber, has problems such as forming and processing due to its high melting temperature. To solve this problem, in this study, fluoride was added to the existing MAS-based glass to increase the workability in the glass manufacturing and to improve the chemical resistance to CF₄/Ar/O₂ plasma gas. Through RAMAN analysis, the structural change of the glass according to the addition of fluoride was observed. In addition, it was confirmed that high-temperature viscosity and thermal properties decreased as the fluoride content increased and plasma resistance was maintained, it showed an excellent etching rate of up to 11 times compared to quartz glass.

• Journal of the Korean Vacuum Society
• /
• v.19 no.3
• /
• pp.206-210
• /
• 2010

Al-doped ZnO thin films were deposited with various Ar flow rate by RF magnetron sputtering, and theire properties were studied. A high-quality thin film was obtained by controlling the Ar flow rate, and the influence of the Ar flow rate on the Al-doped ZnO thin film was confirmed. In all Al-doped ZnO thin films, light transmittance had above 80%. Through Hall measurement and X-ray photoelectron spectrometer, the sample of 60 sccm, which had the lowest resistivity, showed the lower Al concentration. This result was attributed to oxygen vacancy rather than Al concentration.

• The Korean Journal of Ceramics
• /
• v.4 no.3
• /
• pp.189-192
• /
• 1998

The mechanical properties of alkali resistance (AR) glass fiber reinforced cement(GFRC) under different curing conditions were investigated in this study. The specimens were formed by extrusion process, and then steam cured and autoclaved. An autoclaved specimen showed the elastic-brittle behavior up to 4% of fiber volume fraction. However, it was found that the fracture behavior for cured specimen was changed to the elastic-plastic with crack branches fracture at greater than 3 vol.% of fiber.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.6
• /
• pp.34-41
• /
• 1984

MOEN/MO double layer which is to be used It)r the RMOS (refractory metal oxide semiconductor) gate material has been fabricated by means of low temperature reactive sputtering in N2 and Ar mixture. Good Mo2N film was obtained in the volumetric mixture of Ar:N2=95:5. The sheet resistance of the fabricated Mo7N film was about 1.20 - 1.28 ohms/square, which is about an order of magnitude lower than that of polysilicon film, and this would enable to improve the operational speed of devices fabricated with this material. When PSG (phosphorus silicate glass) was used as impurity diffusion source for the source and drain of the RMOSFET in the N2 atmosphere at about 110$0^{\circ}C$, the Mo2N was reduced to Mo resulting in much smaller sheet resistance of about 0.38 ohm/square. The threshold voltage of the RMOSFET fabricated in our experiment was - 1.5 V, and both depletion and enhancement mode RMOSFETs could be obtained.