• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1433-1435
• /
• 1997

ZnO shows the properties of wide conductivity variation, high optical transmittance, and excellent piezoelectricity. Using these properties of ZnO, the material applications were extended to sensors, SAW filters, solar cells, and display devices. This paper investigated transmittance influencing factors for thin film ZnO grown by RF magnetron sputtering. The growth rate and structural investigation were carried out in conjunction with optical transmittance characteristics of thin film ZnO. The glass substrate temperature of $175^{\circ}C$ exhibited a preferential crystallization along (002) orientation. Transmittance of ZnO film deposited at the substrate temperature of $175^{\circ}C$ showed higher than 92%. An active sputter gas was investigated with a variation of $O_2$ partial pressure from 0 to 10% in an Ar atmosphere. ZnO film grown in 100% Ar gas shows that a reduced transmittance of 82% at the short wavelengths and decreased resistivity value. As the partial pressure of $O_2$ gas increased, the optical transmittance was increased above 90% at the short wavelengths, however, resistivity was drastically increased to higher than $10^4{\Omega}$-cm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.6
• /
• pp.470-474
• /
• 2001

This paper describes the fabrication and characteristics of CrN thin-film type pressure sensors, in which the sensing elements were deposited on SuS. 630 diaphragm by DC reactive magnetron sputtering in an argon-nitride atmosphere(Ar-(10%)N$_2$). The optimized condition of CrN thin-film sensing elements was thickness range of 3500$\AA$ and annealing condition(300$\^{C}$, 3 hr) in Ar-10%N$_2$ deposition atmosphere. Under optimum conditions, the CrN thin-films for strain gauges is obtained a high resistivity, ρ=1147.65 $\mu$Ωcm, a low temperature coefficient of resistance, TCR=186ppm/$\^{C}$ and a high temporal stability with a good longitudinal, 11.17. The output sensitivity of fabricated CrN thin-film type pressure sensors is 2.36 mV/V, 4∼20nA and the maximum non-linearity is 0.4%FS and hysteresis is less than 0.2%FS.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.2160-2170
• /
• 1991

Three-dimensional turbulent structures in the near field of elliptic jet were experimentally investigated by using a three-color, three-component Laser Doppler Velocimeter. The Reynolds number based on the nozzle exit velocity and nozzle equivalent diameter(De) was about 4*10$^{4}$. The turbulent characteristics of a sharp-edged elliptic nozzle with aspect ratio of 2 were analyzed along major and minor axis at X/De=2,3,5,7 and along the centerline up to X/De=14. Quantities measured at each point with the 3-D LDV system were three orthogonal velocity components, turbulent intensity, skewness, flatness, and Reynolds shear stress. The nondimensional mean velocities coincided well with the Schlichting's empirical curve with going downstream. Elliptic jet of AR=2 had two switching points at about X/De=2 and 16. The turbulent intensity along the minor axis was distributed widely than that along the major axis. In the near field, X/De<5, the Reynolds shear stresses of the inner part of the elliptic jet had negative value, which indicated the enhancement of entrainment toward the inner part.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.1080-1083
• /
• 2002

In this paper, we have studied with regard to the use of lasers for modifying the surface properties of silicon in order to improve it's wettability and adhesion characteristics. Using an Nd:YAG pulse laser, the wettability and adhesion characteristics of silicon surface have been developed by an Nd:YAG pulse laser. It was found that the laser treatment of silicon surfaces modified the surface energy. In the result of wetting experiments, by the sessile drop technique using the distilled water, wetting characteristic of silicon after the laser irradiation shows a decreased value of the contact angle. In case of the laser treated silicon surface, laser direct writing of copper lines has been achieved by pyrolytic decomposition of copper formate films$(Cu(HCOO)_2{\cdot}4H_2Q)$, using a focused $Ar^+$ laser beam$(\lambda=514.5nm)$ on the silicon substrates. The deposited patterns were measured by energy dispersive X-ray(EDX), Scanning Electron Microscopy(SEM) and surface profiler($\alpha$-step) to examine the cross section of deposited copper lines and linewidth.

• Electrical & Electronic Materials
• /
• v.10 no.3
• /
• pp.262-267
• /
• 1997

In order to improve the brightness and chromaticity of green emitting low voltage phosphor for FED, we examine PL, PLE and CL emission characteristics of ZnGa$_{2}$O$_{4}$:Mn,O prepared in Ar and vacuum. ZnGa$_{2}$O$_{4}$:Mn,O sintered in vacuum shows about 16 times as bright as the one fabricated in Ar and excellent chromaticity. In PL emission spectra of ZnGa$_{2}$O$_{4}$:Mn,O at low temperature of 9 K, two peaks are observed at 504 nm and 513 nm. At room temperature, the two peaks are superimposed due to the lattice thermal vibrational energy, and only one peak is observed at 509 nm. From PLE measurements, it is believed that the energy levels of the host lattice and Mn ions are coexisted. The energy transfer from the host lattice to the emission center of Mn$^{2+}$ ions occurs.s.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.8
• /
• pp.319-324
• /
• 2003

AIN thin films are deposited on Si (100) and $SiO_2$/Si substrates by using an RF magnetron sputtering method and by changing the conditions of deposition variables, such as RF power, $N_2$/Ar flow ratio, and substrate temperature ($T_sub$). For all the deposited AIN films, XRD Peak patterns are monitored to examine the effect of deposition condition on the crystal orientation. Highly (002)-oriented AIN films are obtained at following nominal deposition conditions; RF Power : 350W, $N_2$/Ar ratio = 10/20, T$_{sub}$ : $250^{\circ}C$, and working pressure = 5mTorr, respectively. AIN-based SAW devices are fabricated using a lift-off method by varying the thickness of AIN layer. Insertion losses and side-lobe rejection levels of fabricated SAW devices are extracted from their frequency response characteristics, which are also compared in terms of AIN thickness and substrate. Relationships between the film properties of AIN films and the frequency responses of SAW devices are discussed. It is concluded from the experimental results that the (002)-preferred orientation as well as the surface roughness of AIN film may play a crucial role of determining the device performances of AIN-SAW devices.s.

• Journal of ILASS-Korea
• /
• v.9 no.1
• /
• pp.1-7
• /
• 2004

This paper describes the characteristics of injection rate and macroscopic behavior of fuel spray injected from common-rail type diesel injectors with different nozzle geometries. The injection rates according to the nozzle geometries were measured at different energizing duration of the injector solenoid and injection pressure by using the Bosch's injection rate meter based on the pressure variation in the tube. The spray behaviors injected from the different nozzles were visualized using the spray visualization system composed of an Ar-ion laser, an ICCD camera, and a synchronization system at various injection and ambient pressures. It is revealed that VCO nozzle has higher spray tip velocity at the early stage of injection duration and wider spray cone angle than the mini-sac nozzles. Also the spray cone angle is increased with the increase of nozzle diameter.

• Korean Journal of Biological Psychiatry
• /
• v.11 no.1
• /
• pp.33-39
• /
• 2004

Objective:Nitric oxide(NO) has been known to be associated with tolerance and preference to alcohol. It has also been known to affect various alcohol drinking behavior, alcohol withdrawal symptoms and alcohol- induced brain damage. The purpose of this study was to determine the difference, among alcohol dependence group, alcohol drinking group and abstinence group, in serum concentration of nitrite, a stable metabolite of NO, and it's relationship to clinical and biochemical markers of alcoholism. Methods:Forty subjects diagnosed as alcohol dependence according to DSM-IV diagnostic criteria were evaluated for the clinical characteristics and biochemical markers of alcohol dependence including nitrite with their CIWA-Ar scores checked just after admission. Thirty-nine healthy controls were also evaluated, divided into twenty-three alcohol drinking group and sixteen abstinence group. Clinical characteristics were evaluated by CIWA-Ar, CAGE and AUDIT questionnaires. Aspartate aminotransferase(AST), alanine aminotransferase (ALT), gamma glutamyltransferase(GGT) and mean corpuscular volume(MCV) were used as the biochemical markers of alcohol dependence. Serum nitrite concentrations were measured by Griess reaction. Results:1) The concentrations of nitrite in alcohol dependence patients were not different from those in the control subjects. 2) There were no significant association between the nitrite concentrations and the CIWA-Ar scores in alcohol dependence patients. 3) Nitrites are significantly increased in alcohol dependence group and alcohol drinking group compared with abstinence group. Conclusions:These findings suggest that serum nitrite concentration has no relation with alcohol withdrawal symptoms, but alcohol drinking increases serum nitrite concentration influenced by general condition of the body.

• Solar Energy
• /
• v.15 no.1
• /
• pp.53-71
• /
• 1995

Experiments have been conducted on a planar, free surface jet of water to investigate the effects of aspect ratios(AR=6.67, 15, 26.67), average nozzle velocity($V_0=3.3m/s{\sim}78m/s$) and nozzle-to-plate spacings($Z/W=6{\sim}40$) on the characteristics of heat transfer, when 3 rectangular waterjets impinging on a flat plate which has the uniform heat flux. the scondary peaks which produced by circular jets also produced by rectangular water jets. The position of the scondary peaks depends upon the aspect ratio of nozzle. The heat transfer coefficient was subjected to the influence of aspect ratio. The heat transfer correlations and best position of nozzles which produced maximum heat transfer coefficient at stagnation point are provided.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.34 no.2
• /
• pp.21-37
• /
• 2021

Objectives : Allergic rhinitis(AR) is a common chronic disease that accounts for 10-40% of the world's population. This study aims to analyze the status of claims, prevalence, and medical utilization of allergic rhinitis patients using representative patients sample data. Methods : This study used the National Patients Sample(HIRA-NPS) of the Health Insurance Review and Assessment Service for 7 years(2010-2016). And we defined AR patients as all statements including J30 or a subcategory of J30 as the main disease, using the Korean Standard Classification of Diseases(KCD-7). The trend of AR patients by year was divided into Western medicine(WM) and Korean medicine(KM), and analyzed by subgroup analysis such as inpatient/outpatient, gender, age, insurance type, and care institution. Results : Patients with AR were mainly claimed for first sub diagnosis in WM and major diagnosis in KM, and the number of claims increased about 1.3 times and 1.4 times compared to 2010 in WM and KM, respectively. In addition, the total annual medical expenses in 2016 increased 1.3 times and 1.7 times compared to 2010, respectively. Conclusions : Both WM and KM are showing a steadily increasing trend in medical use due to allergic rhinitis. Further research is needed by considering genetic and environmental factors and individual characteristics, and linking with additional data.