• Journal of Ocean Engineering and Technology
• /
• v.13 no.1 s.31
• /
• pp.62-69
• /
• 1999

67Ni-22Cr-10Al-1Y and $ZrO_2-8Y_2O_3$ were coated on the substrate surface of ST304 and Al2024 by the plasma spraying method. The adgesion of the films varies depending on the substrates and the laminating method. In the case of STS304, the cracks were observed at thermal shock temperature difference ${Delta}T$ of $900^{circ}C$ in the non functionally gradient material(NFGM) and at $1100^{circ}C$ in the functionally gradient material(FGM). The film adhesion of the FGM is better than that of the NFGM in ST304. The cumulative AE count of the FGM of STS304 increased continuously at the bending test. But the NFGM of STS304 showed discontinuity of the AE count. The total AE count for the FGM of STS304 decreased as the number of thermal shock increased, and this tendency was evident as the thermal shock temperature difference increased.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.4
• /
• pp.402-410
• /
• 1996

Recently carbon fiber reinforced plastic(CFRP) has been used structural materials in corrosive environment such as for water, chemical tank and chemical pipes. However, mechanical properties of such materials may change when CFRP are exposed to corrosive environment for long periods of time. Therefore, it is important to understand the effect of moisture absorption on mechanical properties of the CFRP. In this study, degradation behavior of immersed carbon fiber/epoxy resin composite material was investigated using acoustic emission(AE) technique. Fracture toughness test are performed on the compact tension(CT) test specimens that are pilled by two types of laminates $[0^{\circ}_2$/$90^{\circ}_2]_3s$ and $[0^{\circ}_2$/$90^{\circ}_2]_6s$During the fracture toughness test, AE test was carried out to monitor the damage of CFRP by moisture absorption. In spite of the change of moisture absorption rate, the fracture toughness of CFRP was not change. As immersion time increased, AE event count numbers decreased in low amplitude range of AE for amplitude distribution histogram. The event in low amplitude range was known to be generated by debonding of matrix-fiber interface. Therefore, decrease of AE event count numbers in low amplitude range represents that debonding of matrix-fiber interface which was probably generated by moisture absorption.

• Journal of Biosystems Engineering
• /
• v.29 no.3
• /
• pp.261-266
• /
• 2004

This study was Performed to classify the acoustic emission(AE) signal due to surface cracking and moisture movement in the flat-sawn boards of oak(Quercus Variablilis) during drying using the principal component analysis(PCA) and artificial neural network(ANN). To reduce the multicollinearity among AE parameters such as peak amplitude, ring-down count event duration, ring-down count divided by event duration, energy, rise time, and peak amplitude divided by rise time and to extract the significant AE parameters, correlation analysis was performed. Over 96 of the variance of AE parameters could be accounted for by the first and second principal components. An ANN analysis was successfully used to classify the Af signals into two patterns. The ANN classifier based on PCA appeared to be a promising tool to classify the AE signals from wood drying.

• Journal of Ocean Engineering and Technology
• /
• v.26 no.5
• /
• pp.5-10
• /
• 2012

In this study, carbon steel (A53) is used as the material for the pipes in a marine plant and ship industry. Welds are necessary to join the carbon steel, and the effect of this welding on the properties of the carbon steel has been studied by many researchers. In this study, the dynamic behavior of welded carbon steel was studied using an acoustic emission (AE) technique, which is a nondestructive test. There are numerous AE parameters that can be used to analyze the damage behavior of carbon steel by external loading. The AE parameters of energy, cumulative count, amplitude, and AE event were used, and each parameter was differentiated according to the degree of damage to the carbon steel. The energy showed a high level at the elastic range of the load curve, while the amplitude had the highest value at the hardening region. The cumulative count showed a growth tendency similar to the loading curve. In addition, an ultrasonic technique and hardness test were applied to evaluate the mechanical properties according to the base zone, HAZ region, and weld zone of the weld specimen. The velocity and attenuation ratio showed little change between zones, and an evaluation of the ultrasonic waves on each zone of the specimen was found to be a useful method to clarify the mechanical properties of the carbon steel.

• Journal of Applied Reliability
• /
• v.13 no.2
• /
• pp.129-140
• /
• 2013

As a fundamental experimental study for reliability improvement of lithium ion secondary battery, degradation mechanism was investigated by microscopic observation and acoustic emission monitoring. Microstructural observation of the decomposed battery after cycle test revealed mechanical and chemical damages such as interface delamination, microcrack of the electrodes, and solid electrolyte interphase (SEI). Acoustic emission (AE) signal was detected during charge and discharge of lithium ion battery to investigate relationships among cumulative count, discharge capacity, and microdamages. With increasing number of cycle, discharge capacity was decreased and AE cumulative count was observed to increase. Observed damages were attributed to sources of the detected AE signals.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.365-368
• /
• 1995

Rotary Compressor has many AE(Acoustic Emission) sources according to condition of parts because it is operated with combination of various parts. In this study, analysis of AE raw signal generated form Rotary compressor which artificially-made parts inflicted abnormal condition was carried out. AE raw signals were acquired form high-speed A/D board, and many burst type signals were observed. By analyzing burst type signals which is caused form internal AE source,efficient AE parameters for monitoring and diagnosis were presented.

• The Journal of Engineering Geology
• /
• v.20 no.1
• /
• pp.89-100
• /
• 2010

Although various methods for determination of damage threshold in rock have been suggested, clear damage thresholds were determined by some methods, but different thresholds were measured by other methods. We determined the damage thresholds in Hangdeung granite using all the methods suggested, and investigated the best methods, applicability and errors of each method. The crack initiation threshold and the crack damage threshold which are important in investigation of characteristics of crack development and failure were verified by field strength ratio method and long-term constant load test. The crack closure stress and the crack initiation stress were 57.5 MPa and 77.6 MPa, and the most exact values were yielded by crack volumetric strain. The secondary crack initiation stress was 90.6 MPa and AE event count and AE event count rate were the effective methods. The volumetric stiffness, AE event count and AE event count rate were the most effective methods for determination of crack coalescence threshold and crack coalescence stress was 110.3 MPa. The crack damage stress was 127.5 MPa and was measured correctly by volumetric stiffness and AE event count rate. The ratio between crack initiation stress and uniaxial compressive strength was 0.47 which was very similar with the FSR value of 0.46. The ratio between crack damage stress and uniaxial compressive strength was almost the same as the ratio between long-term strength and uniaxial compressive strength, indicating that the crack initiation stress and the crack damage stress measured were correct.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.220-226
• /
• 2003

This paper presents the result of an investigation on the application of the acoustic emission method to the monitoring of fatigue crack initiation, growth and track location in welded joints. Fatigue test was carried out for a typical fillet welded joint of ship structure. AE parameter such as ring down count was analyzed in time domain and crack locations were examined by source location and cluster option which is one of the functions of AE signal processor The usability of AE mettled was confirmed for the detection of the initiation and location of through crack.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.124-130
• /
• 1995

연삭작업에 있어서 요구되는 가공능률과 가공정밀도를 얻기 위해서는 적절한 결합도를 갖는 연삭숫돌을 선택하 는 것이 중요한 요건이 된다. 본 연구에서는 결합도를 평가하기 위한 일정한 기준을 설정할 목적으로 AE계측 시스템을 이용하여 대월식결합도시험방법에 따라 연삭숫돌표면의 일부를 파괴시켰을 때 발생되는 AE신호를 검출 하고 연삭숫돌의 파괴량과 AE 신호특성과의 관계 및 AE를 이용한 결합도평가의 가능성을 검토하였다.

• Journal of the Korean Society of Safety
• /
• v.16 no.4
• /
• pp.7-13
• /
• 2001

Wire electrical discharge machining experiments in conducted to investigate characteristics of acoustic emission (AE) and electrical discharge energy due to current peak (I$_{p}$), pulse on time($\tau$/on/). The AE signals are obtained with a sensor attached to workpiece side. Machining states are identified with scanning electron microscopy and residual stress analyzer. It is demonstrated that the residual stress provide reliable informations about the machining states. Moreover, machining states can be detected successfully using both the residual stress and AE count rate.e.