• Journal of Sensor Science and Technology
• /
• v.8 no.6
• /
• pp.469-475
• /
• 1999

The chips may be produced in the form of either broken chips or unbroken chips in turning process. The unbroken chips are dangerous to the operator and difficult to handle at high speed machining. The signal of Acoustic Emission is related to cutting conditions, tool materials, test conditions and tool geometry in turning. The relationship between AE signal and chip formation was experimentally investigated. The experimental results show that two types of chip formations are possible to classify from the statistical analysis of the amplitude of AE signal. The AE-sensor could be used to monitor the chip condition in turning.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.2
• /
• pp.258-266
• /
• 2012

Recently, Acoustic Emission (AE) technique is widely applied to develop the early fault detection system, and the problem about a signal processing method for AE signal is mainly focused on. In the signal processing method, envelope analysis is a useful method to evaluate the rolling element bearing problems and Wavelet transform is a powerful method to detect faults occurred on gearboxes. However, exact method for AE signal is not developed yet. Therefore, in this paper, two methods, which is Hilbert transforms (HT) and Hilbert-Huang transforms (HHT), will be compared for development a signal processing method for early fault detection system by using AE. AE signals were measured through a fatigue test. HHT has better advantages than HT because HHT can show the time-frequency domain result. But, HHT needs long time to process a signal, which has a lot of data, and has a disadvantage in de-noising filter.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.254-262
• /
• 2003

In this study, acoustic emission (AE) signals due to surface cracking and moisture movement in the flat-sawn boards of oak (Quercus Variablilis) during drying under the ambient conditions were analyzed and classified using the principal component analysis. The AE signals corresponding to surface cracking showed higher in peak amplitude and peak frequency, and shorter in rise time than those corresponding to moisture movement. To reduce the multicollinearity among AE features and to extract the significant AE parameters, correlation analysis was performed. Over 99% of the variance of AE parameters could be accounted for by the first to the fourth principal components. The classification feasibility and success rate were investigated in terms of two statistical classifiers having six independent variables (AE parameters) and six principal components. As a result, the statistical classifier having AE parameters showed the success rate of 70.0%. The statistical classifier having principal components showed the success rate of 87.5% which was considerably than that of the statistical classifier having AE parameters.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.1035-1042
• /
• 1988

The acoustic emission(AE) signal is monitored in milling operation in order to investigate the relationship between the progressive tool wear and the AE signals. A signal processing technique so called time domain averaging(TDA) is presented for the elimination of the influences of the noise imbedded in the periodic signals. The relationship between the progressive tool wear and the AE signals is investigated by varying the cutting speed, feed, depth of cut and the number of insert. From the measured data, it is observed that the averaged level of the AE signal increases at first with the increase of flank wear to a certain critical value, and then stays almost constant or fluctuates with further increase of the flank wear.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.5
• /
• pp.480-487
• /
• 2003

To improve environmental control in various plants, signal characteristics of plants have been studied by a nondestructive technique. In this paper, the acoustic emission (AE) from plants was analyzed for water stress dependency. AE signals were taken from gymnosperm and angiosperm. AE sensor detected AE signals from the plant stem underneath the plant surface below the sensor. AE hit-event counts in daytime were more than those in night time, and it was found that the daily hit counts pattern was strongly affected by the water stress in the plant. frequency bands of AE signals from the angiosperm was different from those from the gymnosperm. Frequency bands of AE in outdoor condition were in accord with those in indoor having similar conditions.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.1
• /
• pp.48-57
• /
• 2007

The fatigue crack growth behavior of a cracked and patch-repaired Ah2024-T3 panel has been monitored by acoustic emission(AE). The overall crack growth rate was reduced The crack propagation into the adjacent hole was also retarded by introducing the patch repair. AE signals due to crack growth after the patch repair and those due to debonding of the plate-patch interface were discriminated by usiag the principal component analysis. The former showed high center frequency and low amplitude, whereas the latter showed long rise tine, low frequency and high amplitude. This type of AE signal recognition method could be effective for the prediction of fatigue crack growth behavior in the patch-repaired structures with the aid of AE source location.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.8
• /
• pp.863-867
• /
• 2014

In this study, an acoustic emission (AE) sensor was used for measuring the abrasive and molecular-scale phenomena in chemical mechanical polishing (CMP). An AE sensor is a transducer that converts a mechanical wave into an electrical signal, and is capable of acquiring high-level frequencies from materials. Therefore, an AE sensor was installed in the CMP equipment and the signals were measured simultaneously during the polishing process. In this study, an AE monitoring system was developed for investigating the sensitivity of the AE signal to (a) the variations in the material properties of the pad, slurry, and wafer and (b) the change in conditions during the CMP process. This system was adapted to Oxide and Cu CMP processes. AE signal parameters including AE raw frequency, FFT, and amplitude were analyzed for understanding the abrasive and molecular-level phenomena in the CMP process. Finally, we verified that AE sensors with different bandwidths could function in complementary ways during CMP process monitoring.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.4
• /
• pp.308-315
• /
• 2009

Because the attenuation of AE signal in composite materials is relatively higher than that of metallic materials, it is required to develop a damage assessment technique less affected by the attenuation property of composite materials in order to use AE sensing as a damage detection method. In the signal processing procedure, it is profitable to use the leading wave that arrives first because the leading wave is less influenced by the boundary conditions. Using wavelet transform, we investigated the frequency characteristics of impact induced AE signals focused on the leading wave in advance and chose the key factors to discriminate the damaged condition quantitatively. In this research, we established a damage assessment technique using the sharing percentage of the wavelet detail components of AE signal, and conducted a low-velocity impact test on composite laminates to confirm the feasibility of the proposed signal processing method.

• Composites Research
• /
• v.14 no.5
• /
• pp.46-53
• /
• 2001

In this research, damage behavior of singly oriented ply (SOP) fiber metal laminate (FML) subjected to concentrated load was studied. The static indentation tests were conducted to study fiber orientation effect on damage behavior of FML. During the static indentation tests, acoustic emission technique (AE) was adopted to study damage characteristics of FML. AE signals were obtained by using AE sensor with 150kHz resonance frequency and the signals were compared with indentation curves of FML. The damage process of SOP FML was divided by three parts, i.e., crack initiation, crack propagation, and penetration. The AE characteristics during crack initiation show that the micro crack is initiated at lower ply of the plate, then propagate along the thickness of the plate with creating tiber debonding. The crack grow along the fiber direction with occurring 60∼80dB AE signal. During the penetration, the fiber breakage was observed. As fiber orientation increases, talc fiber breakage occurs more frequently. The AE signal behaviors support these results. Cumulative AE counts could well predict crack initiation and crack propagation and AE amplitude were useful for the prediction of damage failure mode.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.1
• /
• pp.112-122
• /
• 1995

본 연구에서는 절삭공구가 채터진동을 일으킬때 AE(Acoustic Emission) 신호와 어떤관계가 있는지를 실험적으로 연구하였다. 모달분석을 통하여 절삭공구의 고유진동수 및 모우드형상을 구하였으며, 실제 절삭실험에서는 이송방향 및 절삭방향의 가속도를 계측하여 위상치를 결정하었다. AE신호와 두 가속도 와의 관계를 알기위하여 AE 실험을 하였다. AE신호의 폭발점은 대개 Lissajous loop의 방향전환점에서 관찰 되었다.