• Journal of Korea Foundry Society
• /
• v.26 no.5
• /
• pp.211-216
• /
• 2006

The study for thixoextrusion process of 7075, 7003 Al wrought alloys and AZ31 Mg wrought alloy was carried out with respect to reheating rate, isothermal holding temperature and time with an emphasis to the effect of homogenization on thixotropic micro-structures during the partial remelting, especially in the low liquid fraction ($f_L<0.2$). The liquid fraction and average grain size with respect to reheating profile such as reheating rate, isothermal holding temperature and time were almost uniform. It is considered very useful for thixoextrusion in terms of process control such as billet temperature control and actual extrusion time. Micro-structural controls of 7075, 7003 Al wrought alloys and AZ31 Mg wrought alloy before and after homogenization were available and thixotropic microstructures were obtained in both specimens.

• Journal of Korea Foundry Society
• /
• v.26 no.5
• /
• pp.217-221
• /
• 2006

The main emphasis of this study was to utilize thixoextrusion process for improving extrudability of 7075, 7003 Al wrought alloys and AZ31 Mg wrought alloy. The results of thixbextrusion experiments about microstructures and extrusion pressures were compared with conventional hot extrusion results. The maximum extrusion pressure of thixoextrusion was greatly decreased compared with that of conventional hot extrusion. It was pointed out that the extrusion temperature dependence of the maximum extrusion pressure was large and the influence of extrusion temperature on the improvement of extrudability was remarkable in thixoextrusion. This will contribute to extrudability in terms of extrusion pressure, which in turn means that shorter process time is required and smaller extrusion machine can be applied for the same operation. The elongated grains to extrusion direction were generally observed during conventional hot extrusion, while the thixoextruded microstructures were isotropic.

• Korean Journal of Veterinary Research
• /
• v.28 no.2
• /
• pp.365-369
• /
• 1988

The present study was done to demonstrate ADV antigens in frozen and paraffin sections from ADV-infected pigs and cell cultures by using of the IGS method. Tissue specimens from 3 young pigs infected with ADV-phylaxia strain and of 2 healthy pigs were used. Fibroblastic cells originated from pig brain and BHK cells were grown and confluent monolayers were infected with the virus. Two monoclonal antibodies and a specific hyperimmune serum to ADV were used as the source of primary antibodies for both the IGS and immunoperoxidase methods. Application of the IGS method yielded a black fine granular reaction in positive areas, and the results were superior to those obtained using the immunoperoxidase technique for all cases tested. The IGS method might be useful in the detection of various viral antigens in tissue sections.

• Korean Journal of Veterinary Research
• /
• v.35 no.2
• /
• pp.369-374
• /
• 1995

Aujeszky's disease virus(ADV) was inoculated intranasally into the Korean native goats to investigate pathological findings and pathogenesis of ADV infection by using of histological and immunohistochemical methods and in situ hybridization(ISH). Clinical signs of salvation, pyrexia, pruritus and staggering were followed by death with five days after inoculation, Pathoanatomical findings were edema of the lung and the urinary bladder with hemorrhage and congestion, petechial hemorrhages on the endo-and epicardium, renal congestion, moderate splenomegaly and cystic edema. Main microsocpic lesions observed in all infected goats were confined to the CNS and charcterized by perivascular cuffing with lymphocytes and macrophages, focal gliosis, neuronal degeneration and necrosis, and intranuclear inclusion bodies in the neurons and glial cells. Positive reactions to ADV were detected more frequently in the nuclei than in the cytoplasms of infected nerve cells in the CNS by immunohistochemistry and ISH. Frequenctly localized sites of ADV in the CNS were olfactory bulb, prietal cortex, callosal sulcus and corpus callosum. Positive reactions were also detected in the tonsillar epithelium, and alveolar macrophage and sloughed epithelium of the lung.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.517-518
• /
• 2006

In this study, a commercial fixation device, BioFlex, which was designed with shape memory alloy(SMA) for dynamic stabilization of spine was biomechanically evaluated. The finite element model of intact lumbar spine from L1 to S was developed using CT images. Also, low FE models of 2-level(L4-L5-S) and 3-level(L3-L4-L5-S) posteriori fixation using titanium(Ti) rod and BioFlex(SMA) rod. The rotations of bone segments in the intact model and four models were predicted. Although the rotations of the BioFlex fixation model were smaller than those of the intact model, they were relatively larger than those of Ti fixation. The present can be applied for not only evaluation of the stability of interbody fixator, but also development of new implant.

• Korean Journal of Veterinary Pathology
• /
• v.1 no.2
• /
• pp.119-124
• /
• 1997

The objective of this study was to develop digoxigenin (DIG)-labeled in situ hybridization (ISH) test for diagnosis of Aujeszky's Disease(AD) in infected organs. Specific DNA with well conserved gene sequences encoding gp50 antigen in AD virus (ADV) was obtained by Polymerase Chain Reaction (PCR) method. A pair of oligonucleotide primers used in PCR allowed amplification of a 217 bp sequence from the gp50 ADV gene. The DNA was then labeled with DIG by primer labeling method for use as probe in ISH test to detect ADV nucleic acids in various tissue. Positive hybridization was demonstrated by dark pigmentation in nuclei and cytoplasm of ADV infected cells particularly in brain tonsillar crypt epithelium and pulmonary alveolar cells. This result suggests that ISH is a valuable sensitive and rapid diagnostic test for AD.

• Journal of Korea Foundry Society
• /
• v.25 no.6
• /
• pp.254-258
• /
• 2005

Semisolid process is possible in any material system possessing a freezing range where the microstructure should consist of the nondendritic globular solid phase separated and enclosed by the liquid phase, referred to as semisolid slurry. There are two primary semisolid processing routes, thixocasting and rheocasting. Especially, rheocasting process has become a new focus in the field of semisolid process because of its many advantages such as no special billet required and possibility of in-house scrap recycling, compared with the thixocasting process. In-Ladle direct thermal control (DTC) rheocasting has been developed, based on the fact that there is slurry and mush transition in every molten metal and the transition, which normally occurs in the range of liquid traction of 0.1 to 0.6, could be controlled by controlling solid shape and relative solid-liquid interfacial energy. In this study, A356 Al alloy was investigated to verify In-Ladle DTC rheocasting for obtaining semisolid slurry. Modeling of heat transfer was carried out to investigate the effect of pouring temperature and ladle material, geometry and temperature and the simulation results were compared with the actual experiments.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.4
• /
• pp.421-428
• /
• 2005

Dissolved air flotation (OAF) is a solid-liquid separation system that uses fine bubbles rising from bottom to remove particles in water. In this study, we investigated the effect of L/W (L; Length, W; Width) on the hydro-dynamic behavior in DAF system using CFD (Computational Fluid Dynamics) and ADV (Acoustic Doppler Velocimetry) technique. The factual full-scale DAF system, L/W ratio of 1:1, was selected and various L/W ratio (2:1, 3:1, 4:1 and 5:1) conditions were simulated with CFD. For modelling, 2-phase (gas-liquid) flow equations for the conservation of mass, momentum and turbulence quantities were solved using an Eulerian-Eulerian approach based on the assumption that very small particle is applied in the DAF system. Also, for verification of CFD simulation results, we measured the factual velocity at some points in the full-scale DAF system with ADV technique. Both the simulation and the measurement results were in good accordance with each other. As the results of this study, we concluded that L/W ratio and outlet geometry play important role for flow pattern and fine bubble distribution in the flotation zone. In the ratio of 1:1, the dead zone is less than those in other cases. On the other hands, in the ration of 3:1, the fine bubbles were more evenly distributed.

• Ecology and Resilient Infrastructure
• /
• v.5 no.3
• /
• pp.156-162
• /
• 2018

This research aimed at analyzing comparison results between in gravel and sand bed with respect to the detailed Acoustic Doppler Current Profiler (ADCP) measurement in a velocity, depth, and flow rate data based on Acoustic Doppler Velocimeter (ADV) measurement result. Conclusionally, similar results were shown for gravel and sand bed in velocity, depth and flow rate data using ADV and ADCP measurement. The results of the flow rate show a relative error mean of 3.5 - 4.8% in the gravel bed and 0.02 - 3.2% in the sand bed, which is better performance than the mean error of 5% suggested by United States Geological Survey (USGS). The results can be used as a basis data for the measurement of ADCP and potentially able to be utilized for the more detailed uncertainty analysis of ADCP flow rate measurement.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.8
• /
• pp.748-756
• /
• 2015

In this paper, we developed a miniaturized real time video compression system satisfying the military environment using ADV212 and FPGA. We present an efficient hardware design scheme for the weight reduction of the device and also a software solution to deal with noisy image signals. Experimental results show that the frame delay is reduced by a factor of 2 or 3 and the device's weight is decreased by a factor of 6 to 7. In order to prove the reliability for the military usage of this development, we examine the environmental test (MIL-STD-810G) and EMI test (MIL-STD-461F). Experimental results show that the developed system satisfies the requirements.