• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.267-270
• /
• 2014

This paper presents a CMOS interface circuit for vibration energy harvesting. The proposed circuit consists of an AC-DC converter and a DC-DC boost converter. The AC-DC converter rectifies the AC signals from vibration devices(PZT), and the DC-DC boost converter generates a boosted and regulated output at a predefined level. A full-wave rectifier using active diodes is used as the AC-DC converter for high efficiency, and a schottky diode type DC-DC boost converter is used for a simple control circuitry. A MPPT(Maximum Power Point Tracking) control is also employed to harvest the maximum power from the PZT. The proposed circuit has been designed in a 0.35um CMOS process. The chip area is $530um{\times}325um$. Simulation results shows that the maximum efficiencies of the AC-DC converter and DC-DC boost converter are 97.7% and 89.2%, respectively. The maximum efficiency of the entire system is 87.2%.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.412-415
• /
• 2015

This paper presents a MPPT(Maximum Power Point Tracking) control CMOS interface circuit for vibration energy harvesting. The proposed circuit consists of an AC-DC converter, MPPT Controller, DC-DC boost converter and PMU(Power Management Unit). The AC-DC converter rectifies the AC signals from vibration devices(PZT). MPPT controller is employed to harvest the maximum power from the PZT and increase efficiency of overall system. The DC-DC boost converter generates a boosted and regulated output at a predefined level and provides energy to load using PMU. A full-wave rectifier using active diodes is used as the AC-DC converter for high efficiency, and a schottky diode type DC-DC boost converter is used for a simple control circuitry. The proposed circuit has been designed in a 0.35um CMOS process. The chip area is $950um{\times}920um$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.8
• /
• pp.805-808
• /
• 2011

This paper presents a design of high-efficiency and high-power class E power transmitter. The transmitter is composed of 300 Watt class E power amplifier and AC-DC converter. The AC-DC converter converts 220 V and 60 Hz AC to a 290 V DC. The generated DC voltage is directly applied to a bias of the class E power amplifier. Because the converter does not have DC-DC converter unit, it has very high conversion efficiency of about 98.03 %. To minimize the loss at the output of the power amplifier, high-Q inductor was implemented and deployed to the output resonant circuit. As a result, the 13.56 MHz class E power amplifier has a high power-added efficiency of 84.2 % at the peak output power of 323.6 W. The overall efficiency of class E power transmitter, including the AC-DC converter, is as high as 82.87 %.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.4
• /
• pp.617-624
• /
• 2023

Recently, miniaturization and low power consumption of electronic products and improved efficiency and power factor improvement have become a matter of great interest. In this paper, an AC-DC converter based on PWM control was designed and made. The AC-DC converter is designed with a structure in which one rectifier circuit and one output voltage control circuit are connected in series. The rectifier circuit is a diode-based single phase full-wave current circuit and the output voltage control circuit is a DC-DC conversion circuit based on PWM control. Arduino was used as the main control device for PWM control, and LCD was configured at the output stage so that the control result could be checked. The error between the output voltage displayed on the oscilloscope and LCD and the target output voltage was confirmed through repeated experiments with the test circuit, and the validity of the proposed design methodology was confirmed by showing an error rate of about 5% based on the oscilloscope measurement value.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.2
• /
• pp.72-75
• /
• 2012

In this paper, high-efficiency DC-AC converter is implemented for the wireless power transmission. The DC-AC converter is implemented by combining the oscillator and power amplifier. Because the conversion efficiency of wireless power transmitter is strongly affected by the efficiency of power amplifier, the high-efficiency power amplifier is implemented by using the Class-E amplifier structure. Also, because the output power of oscillator connected to the input stage of power amplifier is low, high-gain two-stages power amplifier using the drive amplifier is implemented to realize the high-output power DC-AC converter. The dual band harmonic suppression filter is implemented to suppress 2nd, 3rd harmonics of 13.56 MHz. The output power and conversion efficiency of DC-AC converter are 40 dBm and 80.2 % at the operation frequency of 13.56 MHz.

• Journal of IKEEE
• /
• v.20 no.1
• /
• pp.45-53
• /
• 2016

This paper presents a CMOS interface circuit for vibration energy harvesting with MPPT (Maximum Power Point Tracking). In the proposed system a PMU (Power Management Unit) is employed at the output of a DC-DC boost converter to provide a regulated output with low-cost and simple architecture. In addition an MPPT controller using FOC (Fractional Open Circuit) technique is designed to harvest maximum power from vibration devices and increase efficiency of overall system. The AC signal from vibration devices is converted into a DC signal by an AC-DC converter, and then boosted through the DC-DC boost converter. The boosted signal is converted into a duty-cycled and regulated signal and delivered to loads by the PMU. A full-wave rectifier using active diodes is used as the AC-DC converter for high efficiency, and a DC-DC boost converter architecture using a schottky diode is employed for a simple control circuitry. The proposed circuit has been designed in a 0.35um CMOS process, and the designed chip occupies $915{\mu}m{\times}895{\mu}m$. Simulation results shows that the maximum power efficiency of the entire system is 83.4%.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.369-370
• /
• 2012

본 논문은 380V DC 배전 시스템의 양방향 전력 흐름 제어와 전력 변환 효율 개선을 위한 고효율 절연형 양방향 AC-DC 컨버터를 제안한다. 제안하는 회로는 비절연형 양방향 AC-DC 정류기와 절연형 양방향 CLLC 공진형 컨버터로 구성된다. AC-DC 정류기의 전력 변환 효율 높이기 위해서 단극성 SPWM 방식을 이용하여 SiC 다이오드와 Anti-parallel 다이오드가 없는 IGBT와 MOSFET를 이용하여 전력 변환 효율을 증가 시켰다. 절연형 양방향 DC-DC 컨버터의 효율을 높이기 위해서 전 범위 ZVS 동작이 가능한 양방향 CLLC 공진형 컨버터를 이용하였다. 5kW 시제품을 통하여 제안하는 절연형 양방향 AC-DC 컨버터의 성능을 검증하였다.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.709-712
• /
• 2004

본 논문에서는 고밀도 전원 장치에 적합한 플랫 트랜스포머(Flat Transformer)를 사용하여 다양한 출력을 갖는 AC/DC 변환장치의 설계 예를 제시하였다. 기존의 트랜스포머에 비해 플랫 트랜스포머는 다수의 트랜스포머를 병렬로 구성하여 제작하고, 이차 권선이 항상 1턴으로 구성되므로 누설 인덕턴스가 크게 감소하게 되어 고주파 스위칭에 적합한 형태를 가지고 있다. 일차측 AC/DC 변환기는 고조파 규제를 만족시키기 위해 경계 모드 (Boundary Mode)에서 동작하는 역률 보상회로로 구성하여 설계하였으며, 이차측 DC/DC 변환기는 플랫 트랜스포머에 적당한 하프 브리지(Half-Bridge) 컨버터를 적용하였다. 본 논문에서는 500W급 AC/]DC 변환기를 구성하여 다양한 출력을 갖는 전원 장치를 설계/제작하였다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.6
• /
• pp.1315-1320
• /
• 2012

In this study, piezoelectric AC-DC converter using ring-dot type multilayer piezoelectric transformer with no anisotropic of polarization was developed. Considering the characteristics of piezoelectric transformer which is very narrow operating frequency range, piezoelectric converter was designed with mixed structure of PFM driving method for feedback control of oscillation frequency and PWM driving method for output control. Maximum power and allowed current of the developed piezoelectric converter showing stable driving with minimum heat was 25W and 900mA, respectively. The output voltage of the piezoelectric converter was controlled by the driving oscillation frequency and showed stable and efficient operating characteristics at the maximum power.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.10
• /
• pp.2253-2260
• /
• 2012

In this paper, an efficient hardware architecture is proposed for inverse transform and inverse quantization of H.264/AVC decoder. The previous inverse transform and quantization architecture has a different AC and DC coefficients decoding order. In the proposed architecture, IQ is achieved after IT regardless of the DC or AC coefficients. A common operation unit is also proposed to reduce the computational complexity of inverse quantization. Since division operation is included in the previous architecture, it will generate errors if the processing order is changed. In order to solve the problem, the division operation is achieved after IT to prevent errors in the proposed architecture. The architecture is implemented with 3-stage pipeline and a parallel vertical and horizontal IDCT is also implemented to reduce the operation cycle. As a result of analyzing the proposed ITIQ architecture operation cycle for one macroblock, the proposed one has improved by 45% than the previous one.