• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1552-1553
• /
• 2011

The HVDC transformer which is one of the main equipments for HVDC(High Voltage Direct Current) electric power transmission systems is exposed to not only AC voltage but also the inflowing DC voltage which comes from the DC-AC converter systems. Therefore, the HVDC transformer insulation system is required to withstand the electric field stress under AC, DC and DC polarity reversal conditions. However the electric field distributions under those conditions are different because the AC electric field and DC electric field are governed by permittivity and conductivity, respectively. In this study, the changes of electric potential and electric field of conventional AC transformer insulation system under DC polarity reversal test condition were analyzed by FEM(Finite Element Method). The DC electric field stress was concentrated in the solid insulators while the AC electric field stress was concentrated in the mineral oil. In addition, the electric stress under that condition which is affected by the surface charge accumulation at the interfaces between insulators was evaluated. The stress in some parts could be higher than that of AC and DC condition, during polarity reversal test. The result of this study would be helpful for the HVDC transformer insulation system design.

• 한국전기전자재료학회논문지
• /
• 제17권6호
• /
• pp.586-591
• /
• 2004

We studied the dependence of hot-tarrier-induced degradation characteristics on nitrogen concentration in NO(Nitrided-Oxide) gate of nMOS, under ac and dc stresses. The $\Delta$V$_{t}$ and $\Delta$G$_{m}$ dependence of nitrogen concentration were observed, We observed that device degradation was suppressed significantly when the nitrogen concentration in the gate was increased. Compared to $N_2$O oxynitride, NO oxynitride gate devices show a smaller sensitivity to ac stress frequency. Results suggest that the improved at-hot carrier immunity of the device with NO gate may be due to the significantly suppressed interface state generation and neutral trap generation during stress.ess.

• 대한전자공학회논문지SD
• /
• 제44권2호
• /
• pp.13-18
• /
• 2007

본 연구에서는 Lateral DMOS 소자열화 메카니즘이 게이트 산화층의 두께에 따라 다른 것을 측정을 통하여 알 수 있었다. 얇은 산화층 소자는 채널에 생성되는 계면상태와 drift 영역에 포획되는 홀에 의하여 소자가 열화 되고 두꺼운 산화층 소자에서는 채널 영역의 계면상태 생성에 의해서 소자가 열화 되는 것으로 알 수 있었다. 그리고 소자 시뮬레이션을 통하여 다른 열화 메카니즘을 입증할 수 있었다. DC 스트레스에서의 소자 열화와 AC 스트레스에서 소자열화의 비교로부터 AC스트레스에서 소자열화가 적게 되었으며 게이트 펄스의 주파수가 증가할수록 소자열화가 심함을 알 수 있었다. 그 결과로부터 RF LDMOS 에서는 소자열화가 소자설계 및 회로설계에 중요한 변수로 작용할 수 있음을 알 수 있었다.

• Journal of Power Electronics
• /
• 제13권2호
• /
• pp.186-196
• /
• 2013

This paper presents a low voltage-stress AC-linked charge equalizing system for balancing the energy in a serially connected, valve-regulated lead acid battery string using a modular converter that consists of multiple transformers coupled together. Each converter was coupled through an AC-linked bus to increase the overall energy transfer efficiency of the system and to eliminate the problem of the unbalanced charging of batteries. Previous solutions are based on centralized and modularized topologies. A centralized topology requires a redesign of the hardware and related components. It also faces a high voltage stress when the number of batteries is expanded. Modularized solutions use low-voltage-stress, double-stage, DC-linked topologies which leads to poor energy transfer efficiency. The proposed solution uses a low-voltage stress, AC-linked, modularized topology that makes adding more batteries easier. It also has a better energy transfer efficiency. To ensure that the charge equalization system operates smoothly and safely charges batteries, a small intelligent microcontroller was used in the control section. The efficiency of this charge equalization system is 85%, which is 21% better than other low-voltage-stress DC-linked charging techniques. The validity of this approach was confirmed by experimental results.

• 한국생산제조학회지
• /
• 제20권5호
• /
• pp.541-546
• /
• 2011

This study was numerically investigated on thermal deformation of AC4C and AC7A aluminum alloy casting material for manufacturing the automobile tire mold. The metal casting device was used in order to manufacture the mold product of automobile tire at the actual industrial field. The temperature distribution and the cooling time of these materials were numerically calculated by finite element analysis. Thermal deformation with stress distribution was also calculated form the temperature distribution results. The thermal deformation was closely related to the temperature difference between the surface and inside of the casting. As shown by numerical analysis result, the thermal deformation of AC7A casting material became higher than AC4C casting material. In addition, the results of displacement and stress distributions appeared to be larger at the center parts of casting than on its sides because of the shrinkage caused by the cooling speed difference.

• 한국컴퓨터정보학회논문지
• /
• 제9권1호
• /
• pp.9-15
• /
• 2004

본 논문에서는 드레인 부근의 채널 영역에서 접합 전계를 줄이는 WSW(Wrap Side Wall) 구조의 소자를 제안하였다. WSW구조의 소자 제작은 첫 번째 게이트를 식각한 후에 NM1(N-type Minor1) 이 온주입을 하고 다시 질화막을 덮어 식각함으로서 만들어진다. 새로운 WSW구조는 전계를 줄이기 위한 버퍼층으로 되어 있으며 WSW소자와 LDD구조의 소자 수명을 비교하였으며 핫-캐리어 열화 특성도 분석하였다. 또한 AC 핫-캐리어 열화를 칩 상에서 평가하기 위해 펄스 발생기, 레벨 시프터, 주파수 분배기를 포함한 테스트 패턴 회로를 설계하였다. 이러한 것은 AC와 DC 스트레스간의 핫-캐리어 열화 조건이 AC와 DC 스트레스 모두 동일한 물리적 메커니즘을 지닌다는 것을 알 수 있었다. 따라서 일반적으로 회로 동작 조건 하에서 DC 핫-캐리어 열화 특성을 토대로 AC 소자 수명도 예측할 수 있었다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2004년도 춘계학술발표대회 및 제6회 신소재 심포지엄
• /
• pp.82-82
• /
• 2004

• 대한조선학회논문집
• /
• 제46권5호
• /
• pp.498-509
• /
• 2009

Present study is concerned with the simulation of plasticity models for the cyclic stressstrain behavior of aluminum alloy AC4C-T6 that can be used for primary materials of LNG cargo pump. Material model of cyclic hardening and plasticity for aluminum alloy AC4C-T6 was investigated through experiments and numerical simulations. Monotonic tensile and cyclic tension-compression test under symmetric load cycles was performed at both room temperature and cryogenic temperature of $-165^{\circ}C$. Based on the experimental data plastic hardening models were evaluated for isotropic/kinematic/combined hardening. FEA (Finite Element Analysis) models which describe the cyclic stress-strain relationship were evaluated for the simulation of plasticity. An appropriate hardening model is proposed comparing the results of FEA with those of experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.275-277
• /
• 2006

This paper proposes a snubber circuit for a PWM Cuk AC-AC converter. The proposed snubber makes use of an Undeland snubber as a commutation aids. So the snubber keeps such good features as small count of snubber elements, reduction of voltage/current stress of main switching devices and improved efficiency. This paper shows simulation results to verify the adaptability and feasibility of the proposed snubber.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2006년도 전력전자학술대회 논문집
• /
• pp.143-145
• /
• 2006

This paper proposes a snubber circuit for a PWM AC-AC Cuk converter. The proposed snubber applies a modified Undeland snubber as a commutation aid. The snubber circuit has some good features such as reduction of voltage/current stress of the main switches, improved efficiency. The experiment results show the adaptability and feasibility of the proposed snubber circuit.