• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.7
• /
• pp.474-480
• /
• 2003

We designed and tested a new scan driver output stage. Compared to conventional CMOS structured scan driver IC′s, the new NMOSFET-only scan driver circuit can reduce the chip area and therefore, the chip cost considerably. We confirmed the circuit operation with open drain power NMOSFET IC′s by driving 2"PDP test panel. We defined critical device parameters and their optimization methods lot the best circuit performance.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1394-1396
• /
• 2004

Study passing method of AC/DC Dead ection of urban train and operation time of related device. And search the reason for operation of MCB(Main Curcuit Breaker) and find the safe method to pass dead section.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2515-2517
• /
• 1999

In this paper we analysis DC bus voltage stress at high line voltage and light load in $S^4$-PFC Isolated AC/DC converter with DC bus voltage feedback using coupling in transformer. In this converter, the principle of operation and the practical problems in the design are considered. Simulation and experimental results are presented to verify the operation and performance of the $S^4$-PFC converter with DC bus voltage feedback. Experimental sets are performed in the conditions; switching frequency 100 kHz, output of 5 V, 60W, and universal line input voltage.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1822-1824
• /
• 1996

Damage and upset of control and communication equipment due to transient overvoltages which occur due primarily to internal switching surge and external lightning surge are an important problems in electromagnetic compatibility(EMC). In this paper, we analyzed operation characteristic of metal oxide varistor widely used low voltage AC line using the electromagnetic transients program(EMTP) and compare it with experimental results and also, we modeled combination generator producing $1.2/50{\mu}s$ open circuit voltage and $8/20{\mu}s$ short circuit current as a source which is critical in calculating operation characteristic. Simulation results showed that most of Transient energy consumes at MOV located in service entrance side than load side, and it showed similar to experimental results. Therefore, entrance side MOV should be selected more energy capacity than that of load side MOV.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.4
• /
• pp.704-711
• /
• 2013

Data center is an information hub and resource for information-centric society. Since data center houses hundreds to ten thousands servers, networking and communication equipment, and supporting systems energy saving is one of the hottest issues for green data center. Among several solutions for green data center this paper introduces higher voltage direct current (DC) power feeding system. Contrary to legacy alternating current (AC) power feeding system equipped with Uninterruptible Power Supply (UPS), higher voltage DC power feeding system is reported to be a more energy efficient and reliable solution for green data center thanks to less AC/DC and DC/AC conversions. Main focus of this paper is on reliability issue for reliable and continuous operation of higher voltage DC power feeding system. We present different types of configuration of the power feeding systems according to the level of reliability. We analyze the reliability of the power feeding systems based on M/M/1/N+1/N+1 queueing model. Operation of the power feeding system in case of failure is also presented.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.106-109
• /
• 2003

This paper describes an AC voltage regulator using AC chopper and auxiliary transformer which is series connected with main input. It has many advantages such as fast voltage control, high efficiency and low THD. A detail study of step down AC voltage regulator is described and two kinds of novel step-up/down voltage regulator for AVR are proposed. The operation principle and PWM method of the proposed regulator are described. Experimental results show that it can be used as AC voltage regulator for special purpose very efficiently.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.2
• /
• pp.158-163
• /
• 2009

A shading ring in an AC solenoid plays an important role in reducing vibration and humming sound. Estimation of performance of the shading ring placed in a stator pole of the AC solenoid is not an easy task due to the difficulty in measurement of the current and flux linkage of the shading ring. In this paper, dynamic performance of an AC solenoid with a shading ring is analyzed through the simulation using electromagnetic analysis software and the results are verified by simple AC and DC voltage tests. Both the simulation and experimental results show that the shading ring in the AC solenoid not only increases pull force, but also reduces operation time, vibration and humming sound.

• Proceedings of the KIEE Conference
• /
• 2004.07e
• /
• pp.76-79
• /
• 2004

This paper proposed that the conventional three phase AC-DC converter with bulk LC output filter has been widely used in the industry because of simple circuit, low cost and high power factor (90%). One of the biggest drawback of this three phase AC-DC converter is bulk and heavy. This is serious especially for aerospace applications. To solve this problem a new simple three phase AC-DC converter is presented. Operation of the proposed high power factor three phase AC-DC converter is illustrated and verified by PSpice simulation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.169-176
• /
• 2005

In this paper, a DC and small-signal AC modeling for the active-clamp, ful1-bridge boost converter is described. Based on the operation principle, the ac part of the converter can be replaced by a dc counterpart. Then, a conceptual equivalent circuit is derived by rearranging the switches. The equivalent circuit for this converter consists of CCM(Continuous conduction mode) boost and DCM(Discontinuous conduction mode) buck converter. The analyses for the equivalent CCM boost and DCM buck converter are done using the model of PWM switch. The theoretical modeling results are confirmed through experiment or SIMPLIS simulation.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.67 no.2
• /
• pp.63-69
• /
• 2018

In this paper, the operation principle of a bi-directional switch type resonant AC link snubber circuit was described, together with the practical design procedure, which employs in the proposed power module bridge package type resonant AC link snubber. The novel prototype of power module bridge package type resonant AC link snubber-assisted voltage type sinewave soft switching PWM inverter using IGBT power module was demonstrated herein. It was verified that both the auxiliary power switches in this resonant AC link snubber circuit and the main power switches commutate under the condition of soft switching commutation principle. In addition, the power losses of the new soft switching inverter treated here were analyzed by implementing the experimental data of the IGBT and diode v-i characteristics in addition to switching power loss characteristics into our original computer simulation software developed by the authors. Then, the voltage type sinewave soft switching PWM inverter was high efficiency than that of hard switching PWM inverter, along with performance operation waveforms. In the future, the comparative feasibility study of power module bridge type resonant AC link snubber and its related soft switching inverter in addition to the other types resonant snubber assisted soft switching inverter should be done from a practical point of view.