• Journal of Information Display
• /
• v.2 no.4
• /
• pp.63-67
• /
• 2001

The switching power loss due to the panel capacitance during sustain period in AC PDP driving system can be minimized by using the energy recovery circuits. We proposed a new energy recovery circuit, SER1 (Seoul national univ. Energy Recovery circuit 1st). The experimental results of its application to a 42-inch surface discharge type AC PDP showed superior performance of SER1 in energy recovery efficiency and low distortion voltage waveform. Energy recovery efficiency of SER1 was measured up to 92.3 %, and the power dissipation during the sustain period was reduced by 15.2 W in 2000 pulse/frame compared with serial LC resonance energy recovery circuit.

• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.125-128
• /
• 2006

This paper presents a novel type soft switching PWM power frequency AC-AC converter using bidirectional active switches or single phase utility frequency AC-high frequency AC matrix converter. This converter can directly convert utility frequency AC (UFAC, 50Hz/60Hz) power to high frequency AC (HFAC) power ranging more than 20kHz up to 100kHz. A novel soft switching PWM prototype of high frequency multi-resonant PWM controlled UFAC-HFAC matrix converter using antiparallel one-chip reverse blocking IGBTs manufactured by IXYS corp. is based on the soft switching resonance with asymmetrical duty cycle PWM strategy. This single phase UFAC-HFAC matrix converter has some remarkable features as electrolytic capacitor DC busline linkless topology, unity power factor correction and sine-wave line current shaping, simple configuration with minimum circuit components, high efficiency and downsizing. This series load resonant UFAC-HFAC matrix converter, incorporating bidirectional active power switches is developed and implemented for high efficiency consumer induction heated food cooking appliances in home uses and business-uses. Its operating performances as soft switching operating ranges and high frequency effective power regulation characteristics are illustrated and discussed on the basis of simulation and experimental results.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.812-814
• /
• 2004

AC loss is one of the important parameters in (High Temperature Superconducting)HTS AC devices. Among the HTS AC power devices, the transformer is the essential part in the electrical power system. But unfortunately, the transformer is the worst HTS device concerning AC loss because of very large magnetization loss due to high magnetic field applied to the HTS wire. We calculated the magnetization losses in HTS pancake windings for transformer according to the operating temperature. Two kinds of arrangement of HTS pancake windings were adopted for calculation of AC losses of a shell type transformer, and the analysis results were presented and discussed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.6
• /
• pp.494-501
• /
• 2006

In this paper, a novel energy recovery circuit for AC PDPs(Plasma Display Panels) with reduced sustain voltage is proposed to improve the performance of conventional circuits such as TERES(TEchnology of REciprocal Sustainer). In the TERES circuit, the sustain voltage is the half of general sustaining driver for AC PDPs, however, there is no energy recovery circuit. In the proposed circuit, the efficiency is heightened by installing in energy recovery circuit and the loss of switching device is reduced by performing the zero voltage switching or zero current switching. Although the energy recovery circuit is added, the number of active switching elements of the proposed circuit is the same as that of the TERES circuit. The operations of the proposed circuit are analyzed for each mode and its validity is verified by the simulations and experimentation.

• International Journal of Computer Science & Network Security
• /
• v.22 no.3
• /
• pp.355-363
• /
• 2022

This paper presents the modeling for islanded hybrid AC/DC microgrid and the verification of the proposed supervisory controller for energy management for this microgrid. The supervisory controller allows the microgrid system to operate in different power flows through the proposed control algorithm, it has several roles in the management of the energy flow between the different components of the microgrid for reliable operation. The proposed microgrid has both essential objectives such as the maximum use of renewable energies resources and the reduction of multiple conversion processes in an individual AC or DC microgrids. The microgrid system considered for this study has a solar photovoltaic (PV), a wind turbine (WT), a battery (BT), and a AC/DC loads. A small islanded hybrid AC/DC microgrid has been modeled and simulated using the MATLAB-Simulink. The simulation results show that the system can maintain stable operation under the proposed supervisory controller when the microgrid is switched from one operating mode of energy flow to another.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.9
• /
• pp.1674-1683
• /
• 2011

More than 80% of electric loads need DC electricity rather than AC at the moment. If DC power could be supplied directly to the terminal loads, power conversion stages including rectifiers, converters, and power adapters can be reduced or simplified. Therefore, DC microgrids may be able to improve energy efficiency of power distribution systems. In addition, DC microgrids can increase the penetration level of renewable energy resources because many renewable energy resources such as solar photovoltaic(PV) generators, fuel cells, and batteries generate electric power in the form of DC power. The integration of the DC generators to AC electric power systems requires the power conversion circuits that may cause additional energy loss. This paper discusses the capability and feasibility of DC microgrids with regard to energy efficiency analysis through detailed dynamic simulation of DC and AC microgrids. The dynamic simulation models of DC and AC microgrids based on the Microgrid Test System in KEPCO Research Institute are described in detail. Through simulation studies on various conditions, this paper compares the energy efficiency and advantages of DC and AC microgrids.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.606-612
• /
• 2022

Relatively high indoor CO₂ concentration (>1,000 ppm) has a negative impact on human health. In this work, indoor CO₂ adsorbent was developed by impregnating KOH or K₂CO₃ on commercial activated carbon, named as KOH/AC and K₂CO₃/AC. Commercial activated carbon (AC) showed relatively high BET surface area (929 m²/g) whereas KOH/AC and K₂CO₃/AC presented lower BET surface area of 13.6 m²/g and 289 m²/g. Two experimental methods of TGA (2,000 ppmCO₂, weight basis) and chamber test (initial concentration: 2,000 ppmCO₂, CO₂ IR analyzer) were used to investigate the adsorption capacity. KOH/AC and K₂CO₃/AC exhibited similar adsorption capacities (145~150 mg_CO2/g), higher than K₂CO₃/Al+Si supports adsorbent (84.1 mg_CO2/g_sample). Similarly, chamber test also showed similar trend. Both KOH/AC and K₂CO₃/AC represented higher adsorption capacities (KOH/AC: 93.5 mg_CO2/g K₂CO₃/AC: 94.5 mg_CO2/g_sample) K₂CO₃/Al+Si supports. This is due to the KOH or K₂CO₃ impregnation increased alkaline active sites (chemical adsorption), which is beneficial for CO₂ adsorption. In addition, the regeneration test results showed both K-based adsorbents pose a good regeneration and reusability. Finally, the current study suggested that both KOH/AC and K₂CO₃/AC have a great potential to be used as CO₂ adsorbent for indoor CO₂ adsorption.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.4
• /
• pp.338-343
• /
• 2017

Activated carbon has lower electrical conductivity and reliability than other carbonaceous materials because of the oxygen functional groups that form during the activation process. This problem can be overcome by doping the material with heteroatoms to reduce the number of oxygen functional groups. In the present study, N, F co-doped activated carbon (AC-NF) was successfully prepared by a microwave-assisted hydrothermal method, utilizing commercial activated carbon (AC-R) as the precursor and ammonium tetrafluoroborate as the single source for the co-doping of N and F. AC-NF showed improved electrical conductivity ($3.8\;S\;cm^{-1}$) with N and F contents of 0.6 and 0.1 at%, respectively. The introduction of N and F improved the performance of the pertinent supercapacitor: AC-NF exhibited an improved rate capability at current densities of $0.5-50mA\;cm^{-2}$. The rate capability was higher compared to that of raw activated carbon because N and F codoping increased the electrical conductivity of AC-NF. The developed method for the co-doping of N and F using a single source is cost-effective and yields AC-NF with excellent electrochemical properties; thus, it has promising applications in the commercialization of energy storage devices.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.3
• /
• pp.222-226
• /
• 2021

To comply with CE marking requirements, the electromagnetic compatibility (EMC) and low-voltage directive (LVD) tests are conducted on the sub-racks of International Thermonuclear Experimental Reactor (ITER) AC/DC converters and bypass switches. The EMC tests consist of a series of tests, including the electromagnetic interference test, the electromagnetic field immunity test, and the rapid transient burst immunity test. In the LVD test, the electric shock protection test, the xcessive temperature limit and heat resistance of equipment tests, and the fire spread prevention test are performed. This work presents and reviews the European Directive for EMC/LVD and introduces the methods of EMC and LVD tests for the sub-racks of AC/DC converters and bypass switches. It also evaluates the test method and results to meet the European Directive requirements for CE marking. The sub-racks of ITER AC/DC converters and bypass switches successfully pass the EMC and LVD tests.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.407-410
• /
• 2009

A piezoelectric device which converts mechanical vibration energy into electrical energy is able to harvest energy and the usable energy is mW ${\sim}$ W, hence a converter is necessary to acquire the energy efficiently. Various limited conditions should be considered for the design of AC/DC converter for energy harvesting of a piezoelectric device supplying small amount of energy. In addition to simple structure, compact size, light weight and high efficiency, the energy harvesting AC!DC converter should adopt the technique of self operating, in which only the harvested energy from the piezoelectric device is available. This paper proposes new AC/DC resonant boost converter to harvest efficiently electrical energy from mechanical vibration energy, analyzes the operating characteristics of the converter and proves its feasibility for energy harvester with PSPICE simulation and experiment.